msg_anim.sim

proe5.0野火版下载(中文版免费下载)

%CEUSER Nothing to measure
Please select an entity to measure


%CPUSER Select a point for the green body
Select a point for the green body


%CIUSER created parameter for measure
Created parameter for %0s measure


%CIUSER parameters have been created for the selected measures
Parameters have been created for the selected measures


%CWUSER No unique name
Unable to generate a unique name for the new entity


%CEUSER Invalid spring constant
The requested spring constant is invalid.  Please enter a value that is greater than 0.


%CEUSER Invalid spring diameter
The requested spring diameter is invalid.  Please enter a value between 0.05 * U and 0.85 * U.


%CPUSER Enter X component for the Load cell Vector
Enter X component for the Loadcell Vector


%CPUSER Enter Y component for the Load cell Vector
Enter Y component for the Loadcell Vector


%CPUSER Enter Z component for the Load cell Vector
Enter Z component for the Loadcell Vector


%CEUSER Failed to initialize dynamics analysis
Failed to initialize dynamics analysis


%CEUSER dynamics analysis failed at time
Dynamics analysis failed at time %0f


%CPMECH Select a point
Select a point


%CEUSER Invalid point selection
Points selected are in the same body. Please select again.


%CPUSER Select a part middle for WCS
Select a part (middle mouse button for WCS)


%CPUSER Select a part or body middle for WCS
Select a part or body (middle mouse button for WCS)


%CEUSER Time cannot be less that zero
The time value cannot be less that zero.


%CEUSER Minimum time plus step must be less than the maximum time
The minimum time plus the step must be less than the maximum time.


%CEUSER Time step must be greater than zero
The time step value must be greater than zero.


%CEUSER Minimum measure value plus step must be less than the maximum measure value
The minimum measure value plus the step must be less than the maximum measure value.


%CEUSER Measure step must be greater than zero
The measure step value must be greater than zero.


%CEUSER Graphed values must be greater than 1e-6
Graphed values must be geater than 1e-6.


%CEUSER Graph interval exceeds maximum increments
Graph interval exceeds maximum increments.


%CEUSER Reactions on weld connections are not supported
Reactions on weld connections are not supported.


%CEUSER cam follower connection not found
Cam follower connection is not found.


%CPUSER Select a point for the load cell constraint
Select a point for the Loadcell constraint.


%CEUSER Slot Damper Load measure is not supported
Slot Damper Load measure is not supported.


%CEUSER Please enter an angle between 0 and 180 degrees
The offset angle is invalid. Please enter an angle between 0 and 180 degress.


%CEUSER Time values must be greater than zero
Time values must be greater than zero.


%CEUSER The table contains repeat time values
The table contains repeat time values. The time values must be unique.


%CEUSER The table contains repeat values in the first column
The table contains repeat values in the first column. The values in the first column must be unique.


%CEUSER The table must contain at least two pairs of values
The table must contain at least two pairs of values (different time).


%CIUSER The direction of motion is shown by the magenta arrow
The direction of motion is shown by the magenta arrow. Driven entity (body1) is highlighted in orange and reference entity (body2) is highlighted in green.


%CEUSER Empty name used
Invalid name used. The name field can not be empty.


%CPUSER Select a coordinate system
Select a coordinate system


%CPUSER Select a part coordinate system
Select a part coordinate system


%CPUSER Select a part csys middle for part lcs
Select a coordinate system in the part (middle mouse button for Part LCS)


%CPUSER Select a csys middle for body lcs
Select a coordinate system (middle mouse button for Body LCS)


%CEUSER Only numeric values are allowed in input field
Only numeric values are allowed in input field.


%CEUSER Only positive values are allowed in input field
Only positive values are allowed in input field.


%CEUSER Density can not be set for parts with zero volume
Density can not be set for parts with zero volume.


%CPMECH Select a part or assembly
Select a part or assembly


%CIUSER Old result no arrows
This motion result was created in an earlier version of Mechanism. No display arrows will be shown.


%CPUSER Select a csys middle for wcs
Select a coordinate system (middle mouse button for WCS)


%CPUSER Select a point, datum plane or planar surface
Select a point, datum plane or planar surface


%CPUSER Select a point, vertex, datum plane or planar surface
Select a point, vertex, datum plane or planar surface


%CIUSER The cam normal is shown by the magenta arrow
The cam surface normal is shown by the magenta arrow


%CEUSER Impulse measure is not applicable for ball and weld joints
USER Impulse measure is not applicable for ball and weld joints.


%CEUSER Impulse measure is not applicable for this type of general joint
USER Impulse measure is not applicable for this type of general joint.


%CEUSER Slip measure is not applicable for impulse measure category
Slip measure is not applicable for impulse measure category


%CPUSER Select a slot follower connection
Select a slot follower connection


%CEUSER slot follower connection not found
Slot follower connection is not found.


%CPMECH Select an assembly
Select an assembly


%CIUSER Specify density for assembly
Please specify a density to be applied to parts in the assembly model.


%CEUSER Number of axis ticks exceeds maximum
The number of axis ticks exceeds the maximum.


%CEUSER The minimum axis value must be less than the maximum axis value
The minimum axis value must be less than the maximum axis value.


%CEUSER Cam direction cannot be determined. Continue to select surfaces
Autoselect cannot determine the cam direction from the current selections.  Please continue to select surfaces.


%CPUSER Select ref part for locked bodies
Select a reference part for locked bodies (middle button for Ground)


%CPUSER Select parts to lock to reference
Select parts to lock to reference


%CEUSER Only nonzero values are allowed in input field
Only nonzero values are allowed in input field.


%CWUSER Using spline fit for a pos motor in analysis
Using spline fit for position table servo motor %0w in the current analysis.


%CWUSER Using spline fit for a vel motor in analysis
Using spline fit for velocity table servo motor %0w in the current analysis.


%CEUSER The pitch circle diameter must be greater than zero
The pitch circle diameter must be greater than zero.


%CEUSER The rack ratio must be greater than zero
The rack ratio must be greater than zero.


%CEUSER D1 must be greater than zero
D1 must be greater than zero.


%CEUSER D2 must be greater than zero
D2 must be greater than zero.


%CPUSER Select a point or vertex for the pitch circle location.
Select a point or vertex to change the location of the displayed pitch circle.  Middle button for default location


%CPUSER Select a gearpair connection
Select a gearpair connection.


%CEUSER gearpair connection not found
Gearpair connection not found.


%CWUSER ignoring subasm joint axis zeros
Ignoring motion axis zero defined using Make Zero option for subassembly joint %0w. Open subassembly and save model to resurrect motion axis zero.


%CEUSER Subassembly joint axis cannot be edited.
Subassembly motion axis cannot be edited.


%CEUSER Subassembly cam-follower connection cannot be edited.
Subassembly cam-follower connection cannot be edited.


%CEUSER Subassembly cam-follower connection(s) cannot be deleted.
Subassembly cam-follower connection(s) cannot be deleted.


%CEUSER Subassembly slot-follower connection cannot be edited.
Subassembly slot-follower connection cannot be edited.


%CEUSER Subassembly slot-follower connection(s) cannot be deleted.
Subassembly cam-follower connection(s) cannot be deleted.


%CEUSER Subassembly gear pair cannot be edited.
Subassembly gear pair cannot be edited.


%CEUSER Subassembly servo motor cannot be edited.
Subassembly servo motor cannot be edited.


%CEUSER Subassembly force motor cannot be edited.
Subassembly force motor cannot be edited.


%CEUSER Subassembly force/torque cannot be edited.
Subassembly force/torque cannot be edited.


%CEUSER Subassembly spring cannot be edited.
Subassembly spring cannot be edited.


%CEUSER Subassembly damper cannot be edited.
Subassembly damper cannot be edited.


%CEUSER Subassembly measure cannot be edited.
Subassembly measure cannot be edited.


%CEUSER Subassembly initial condition cannot be edited.
Subassembly initial condition cannot be edited.


%CEUSER Invalid parameter name for UDF
This Pro/E parameter cannot be included in the user defined expressions, because the name of this parameter failed to meet the qualifying criteria. A valid name for this operation must contain only alphanumeric characters.


%CEUSER Invalid measure variable for UDF
Selected measure is not a valid selection for user defined functions.


%CIUSER Starting analysis.
%0s started (%1s Analysis).


%CIUSER Analysis completed.
%0s complete.


%CEUSER Analysis failed.
%0s failed.


%CIUSER Analysis interrupted.
%0s interrupted.


%CEUSER Invalid Step Factor
Step Factor value should be greater than 0 and less than or equal to 1.


%CEUSER Subassembly snapshot(s) cannot be exported to Drawing mode.
Subassembly snapshot(s) cannot be exported to Drawing mode.


%CEUSER measure is not computed
%0w measure is not computed for the %1w results.


%CPUSER Select a planar edge or a datum curve
Select a planar edge or a datum curve


%CEUSER Select a valid planar edge or a datum curve
Invalid selection. Please select a planar edge or datum curve for cam-synthesis


%CIUSER Analysis interrupted at.
%0s interrupted with %1s complete.


%CWUSER Gear pair reaction measure warning.
Joint reaction measures computed for gear pair connection joint axes do not include reaction force contribution from gear tooth contact.


%CEUSER Non-unique analysis name
A %0s analysis with specified name already exists. Please enter a unique name.


%CIUSER Graphical display turned off
Graphical display has been turned off.


%CEUSER Constraints of a subassembly snapshot cannot be deleted
Constraint(s) of a subassembly snapshot cannot be deleted.


%CWUSER points no separation at time
There is no separation between points for the pt2pt force at time %0f. The force is not applied at this instance.


%CEUSER Internal Error while opening file
Internal Error while opening file


%CEUSER Error in opening file %0s
Error in opening file %0s


%CEUSER Error in accessing file
Error in accessing file


%CEUSER No model to link with the given file
No model to link with the given file


%CEUSER No file to link with the given model
No file to link with the given model


%CEUSER Unable to link given file with the given model
Unable to link given file with the given model


%CEUSER Table rows exceed max limit 
Please use a table with 20000 or fewer rows.


%CEUSER constraints result in non-orthogonal degrees of freedom
A connection cannot be built using the specified constraints as they result in non-orthogonal degrees of freedom.


%CEUSER constraints are in more than 2 parts
A connection may not be built because the features used in the constraints to specified the connection are in more than 2 parts.


%CEUSER constraints are in the same part
A connection may not be built because the features used in the constraints to specified the connection are in the same part.


%CEUSER invalid contact radius
Invalid contact radius for motion axis friction. Contact radius R must be greater than 0.


%CWUSER zero contact radius
Contact radius R for motion axis friction is 0. Please enter a value which is greater than 0.


%CWUSER ignoring Make Zero setting for connection
Motion axis zero settings for connection %0w have been reset to default. Please redefine motion axis zeros preferably using feature references.


%CEUSER Cannot edit rotation axis settings of a multi rotation DOF joint 
Cannot edit motion axis settings of a rotation axis of a joint with multiple rotation degrees of freedom


%CEUSER Invalid measure name
Invalid name. Measure names may contain alphanumeric characters and underbars only and must begin with an alphabetic character.


%CWUSER Current Position out of range.
The current position of motion axis does not lie within the limits specified.


%CWUSER No license to run dynamics analysis
No license to run the Dynamics analysis


%CEUSER Invalid snapshot name to export to Drawing mode
Cannot export %0s to Drawing mode. Snapshot name contains invalid characters.


%CIUSER Body selected for dragging
Body %0ws is selected for dragging


%CIUSER Body selected as lead body
Body %0ws is selected as lead body


%CIUSER Body added as the follower body to lead body
Body %0ws added as the follower body to lead body