msgtxt_smt.txt

proe5.0野火版下载(中文版免费下载)

%CISmt Cut
Smt Cut


%CLGreen Side
Green Side


%CLWhite Side
White Side


%CIpart name for referencing geometry
part name for referencing geometry


%CPSet angle value to %ws.
Set angle value to %0s.


%CI  BEND SEQ    #BENDS     BEND#      BEND      BEND      BEND      BEND
  BEND SEQ    #BENDS     BEND#      BEND      BEND      BEND      BEND


%CI                               DIRECTION     ANGLE    RADIUS    LENGTH
                               DIRECTION     ANGLE    RADIUS    LENGTH


%CESurface has been already selected.
Surface has been already selected.


%CIBoth
Both


%CLX Axis
X Axis


%CLY Axis
Y Axis


%CPMerge
Merge


%CWUnattached Wall
Unattached Wall


%CEGeometry is not tangent, can't be merged.
Geometry is not tangent, can't be merged.


%CWNo edges selected to be merged.
No edges selected to be merged.


%CPPlease enter the new development length, the current value is %0s. [Quit]:
Please enter the new development length,|||%0s


%CICurrent Rules Table : %0ws.
Current Rules Table : %0w.


%CISHEET MET RULE
SHEET MET RULE


%CPEnter rule table file name [%0w]:
Enter rule table file name|||%0w


%CESheet metal rule table %0w already exists.
Sheet metal rule table %0w already exists.


%CIRule table %0w has been saved.
Rule table %0w has been saved.


%CIRule table %0w will be used to design checking.
Rule table %0w will be used to design checking.


%CI|     Rule name      |      Rule formula       |   Rule  | Current | References|
|     Rule name      |      Rule formula       |   Rule  | Current | References|


%CIRules Violations Diagnostic
Rules Violations Diagnostic


%CIDEVELOPMENT LENGTH DIM ID %-d
DEVELOPMENT LENGTH DIM ID %-d


%CLFirst Wall
FIRST WALL


%CICan NOT select Developed Length dimension.
Can NOT select Developed Length dimension.


%CLTHICK
THICK


%CICreated Point %ws
Created Point %ws


%CIOffset
Offset


%CIWidth = %0g
Width = %0g


%CILength = %0g
Length = %0g


%CIAngle = %0g
Angle = %0g


%CIAttach Edge
Attach Edge


%CITwist Axis
Twist Axis


%CISpecify twist axis.
Specify twist axis.


%CISelect axis point.
Select axis point.


%CICreate Point
Create Point


%CICreate axis point.
Create axis point.


%CIOffset Type
Offset Type


%CISpecify offset type for axis poin.
Specify offset type for axis poin.


%CIPoint Offset
Point Offset


%CIEnter offset value for axis point.
Enter offset value for axis point.


%CIStart Width
Start Width


%CISpecify width of new wall at the attachment edge.
Specify width of new wall at the attachment edge.


%CIEnd Width
End Width


%CISpecify width of new wall at the end.
Specify width of new wall at the end.


%CITwist Length
Twist Length


%CISpecify "twisted" wall length.
Specify "twisted" wall length.


%CITwist Angle
Twist Angle


%CISpecify twist angle.
Specify twist angle.


%CIDevel Length
Devel Length


%CISpecify the length of the "twisted" wall when it is unbent.
Specify the length of the "twisted" wall when it is unbent.


%CICreate a point on the attachment edge and use it.
Create a point on the attachment edge and use it.


%CISelect existing point on the attachment edge.
Select existing point on the attachment edge.


%CLWidth Parameters
Width Parameters


%CLLength Parameters
Length Parameters


%CLAngle Parameter
Angle Parameter


%CPSelect planar surface, point will be offset from.
Select planar surface, point will be offset from.


%CPSpecify twist axis location.
Specify twist axis location.


%CLSelect Surface(Label)
Select Surface


%CISelected Point %0ws
Selected Point %0ws


%CISelect straigth edge where "twisted" wall should be attached.
Select straight edge.


%CISelect, Create axis point or use Middle of the attachment edge.
Select, Create axis point or use Middle.


%CWWrong value %0d. Range is %1d to %2d.
Wrong value %0d. Range is %1d to %2d.


%CWWrong value %0f. Range is %1f to %2f.
Wrong value %0f. Range is %1f to %2f.


%CEFeature aborted. No Base References selected.
Feature aborted. No Base References selected.


%CEFeature aborted. No geometry selected to be merged.
Feature aborted. No geometry selected to be merged.


%CEGeometry does not touch, can't be merged.
Geometry does not touch, can't be merged.


%CIAxis Point
Axis Point


%CILength Ratio
Length Ratio


%CITWIST
TWIST


%CP< Cancel >
                                     < Cancel >


%CPKeep Lines
Keep Lines


%CLFlat Models
Flat Models


%CEFeature aborted. Wall can not be extruded with such depth.
Feature aborted. Wall can not be extruded with such depth.


%CEFeature aborted. Sketcher plane have to intersect the attachment edge.
Feature aborted. Sketcher plane have to intersect the attachment edge.


%CEFeature aborted. Sketcher plane have to be normal to the attachment edge.
Feature aborted. Sketcher plane have to be normal to the attachment edge.


%CLform #%d
form #%d


%CEFeature aborted. Start point have to lie on the attachment edge.
Feature aborted. Start point have to lie on the attachment edge.


%CLCorner
Corner


%CEFeature aborted: wrong depth.
Feature aborted: wrong depth.


%CPSelect chain of split edges.
Select chain of split edges.


%CPFlip Split Direction.
Flip Split Direction.


%CPSelect driven surface.
Select driven surface.


%CIHem
Hem


%CLTBL NAMES
TBL NAMES


%CWApplying new default corner relief will cause part regeneration.
Applying new default corner relief will cause part regeneration.


%CIForm placement is not validly constrained.
Status: Form placement is not fully constrained. 


%CIForm is fully constrained and can be placed.
Status: Form is fully constrained and can be placed.


%CIForm is partially constrained but can be packaged.
Status: Form is partially constrained but can be packaged.


%CIForm has no constraints but can be packaged.
Status: Form has no constraints but can be packaged.


%CIForm constraints are invalid.
Status: Form constraints are invalid.


%CLMIN_DIST_BTWN_CUTS
MIN_DIST_BTWN_CUTS


%CLMIN_CUT_TO_BOUND
MIN_CUT_TO_BOUND


%CLMIN_CUT_TO_BEND
MIN_CUT_TO_BEND


%CLMIN_WALL_HEIGHT
MIN_WALL_HEIGHT


%CLMIN_SLOT_TAB_WIDTH
MIN_SLOT_TAB_WIDTH


%CLMIN_SLOT_TAB_LENGTH
MIN_SLOT_TAB_LENGTH


%CLMIN_LASER_DIM
MIN_LASER_DIM


%CICommit and Exit
Commit and Exit


%CIExit Without Changing
Exit Without Changing