msgtxt_dial.txt

来自「proe5.0野火版下载(中文版免费下载)」· 文本 代码 · 共 3,234 行 · 第 1/5 页

%CPHelp line for TRIM_NONE
Use sketched entry/exit trajectories as specified.


%CPHelp line for RETRACT_PLANE
Set approach/exit path to be at the height of the retract plane.


%CPHelp line for DEPTH_OF_CUT
Set approach/exit path to be at the depth of the start/end point of the pass.


%CPHelp line for EXIT_DISTANCE
Set length of exit moves created in build path.


%CPHelp line for OVERTRAVEL_DISTANCE
Specify the distance the tool is to travel past the surface outline.


%CIHelp line for LEADING_EDGE
The leading edge will clear the selected surface by OVERTRAVEL_DISTANCE.


%CIHelp line for HEEL
The heel of the tool will clear the selected surface by OVERTRAVEL_DISTANCE.


%CPHelp line for PERCENT_DEPTH
Specify percentage (0-1) of material to be removed in each pass.


%CIHelp line for NUMBER_FIN_PASSES
Number of finishing passes to be made after final thread depth is reached.


%CIHelp line for BIAS_FEED
Feed rate option for thread cutting.


%CIHelp line for NUMBER_STARTS
The number of threads for multiple start threading applications.


%CPHelp line for NUM_TRANSVERSE_CUTS
Set the number of cuts needed to complete thread creation per thread.


%CPHelp line for CUT_OFFSET
Set the distance between cuts in transverse cut threads.


%CIHelp line for INFEED_ANGLE
Tool motion angle for entering the thread.


%CPHelp line for THREAD_DEPTH
Set depth of thread to cut.


%CPHelp line for LOCATION
Set the machine location.


%CPHelp line for CONTROLLER
Set the controller name.


%CPHelp line for SPINDLE_HP
Set spindle horsepower.


%CPHelp line for RAPID_FEED_RATE
Set feed rate used for rapid traverse motions (0 = RAPID).


%CPHelp line for TOOL_CHANGE_TIME
Set time required to change tools (used in time computations).


%CIHelp line for CELL_X_MIN
Sets minimum limit for the workcell travel in the X direction.


%CIHelp line for CELL_X_MAX
Sets maximum limit for the workcell travel in the X direction.


%CIHelp line for CELL_Y_MIN
Sets minimum limit for the workcell travel in the Y direction.


%CIHelp line for CELL_Y_MAX
Sets maximum limit for the workcell travel in the Y direction.


%CIHelp line for CELL_Z_MIN
Sets minimum limit for the workcell travel in the Z direction.


%CIHelp line for CELL_Z_MAX
Sets maximum limit for the workcell travel in the Z direction. 


%CIHelp line for CELL_MAX_FEED
Sets a maximum allowable feed rate for the workcell.


%CIHelp line for CELL_MAX_SPINDLE
Sets maximum allowable spindle speed for workcell.


%CIHelp line for CUTCOM_MOVE
Length of linear move used to turn cutter compensation ON or OFF.


%CIHelp line for MIN_STEP_DEPTH
Minimum allowable step down to next cut.


%CPHelp line for TOOL_OVERLAP
Control step over of tool by overlap distance (exclusive of STEP_OVER).


%CPHelp line for NUMBER_CUTS
Set number of cuts to machine to depth (exclusive of STEP_DEPTH in milling).


%CIHelp line for INDEXABILITY
Acknowledges the presence of an indexable tool head.


%CIHelp line for RESULT_GEOMETRY
Specifies if the material removed during NC sequence will be shown on screen.


%CIHelp line for SIMPLIFIED
Material will be removed when the NC sequence is complete.


%CIHelp line for NO_GEOMETRY
The material will not be removed when the NC sequence is complete.


%CPHelp line for SPINDLE_RANGE
Set the spindle speed range.


%CIHelp line for APPROXIMATE_SPLINE
Approximate all splines with straight line segments and arcs.


%CPHelp line for LOOP_CUT_DIR
Set direction for cutting closed loops in contouring NC sequence.


%CPHelp line for APPR_EXIT_HEIGHT
Control the depth of approach and exit paths in Build Slice.


%CIHelp line for CL_DATA_MODE
Controls format of CL data to include ROTATE or i,j,k axis vectors.


%CIHelp line for CYCLE_FORMAT
Specifies the output format for CL data for a holemaking NC sequence.


%CPHelp line for DELAY_UNITS
Specify units (revolutions or seconds) for delay during holemaking.


%CPHelp line for OUTPUT_POINT
Choose point on the tool that will be used as the control point for CL output.


%CPHelp line for LACE_OPTION.
Determine if the tool retracts at the end of each tool pass.


%CPHelp line for OUTPUT_TREAD_PNTS
Turn on or off initial and final points for the threading motion.


%CPHelp line for SPEED_CONTROL
Set the units for specifying the spindle speed.


%CPHelp line for SPINDLE_STATUS
Set the status of the spindle to On or Off.


%CLHelp line for CORNER_ROUND
CORNER_ROUND


%CPHelp line for DEFAULT
Set option to DEFAULT.


%CPHelp line for DRILL
Use a DRILL canned cycle.


%CPHelp line for BORE
Use a BORE canned cycle


%CPHelp line for DEEP
Use a DEEP drill canned cycle.


%CPHelp line for THREADS_PER_INCH
Set the number of threads per inch for the thread.


%CLHelp line for EXTENSION_MARGIN
EXTENSION_MARGIN


%CLHelp line for FLAT_EXTENSION
FLAT_EXTENSION


%CLHelp line for LOW
LOW


%CLHelp line for HIGH
HIGH


%CLHelp line for NONE
No automatic tool motion.


%CLHelp line for MEDIUM
MEDIUM


%CLHelp line for IN
IN


%CLHelp line for OUT
OUT


%CIHelp line for FACE
Perform a facing NC sequence.


%CPHelp line for AMERICAN_STANDARD
Set thread type to AMERICAN_STANDARD.


%CPHelp line for ACME
Set thread type to ACME.


%CPHelp line for BUTTRESS
Set thread type to BUTTRESS.


%CPHelp line for TRAP_STATUS
Cycle the trap at the end of the NC Sequence.


%CIHelp line for TIP_RIGHT
Tool control point is tip from right side of tool.


%CIHelp line for X_OFFSET_RIGHT
Tool control point is from right radius offset along machine X Axis.


%CIHelp line for Z_OFFSET_RIGHT
Tool control point is from right radius offset along machine Z Axis.


%CIHelp line for MAX_OVERLAP_DIST
Sets the maximum overlap of successive tool strokes (nibbling sequence).


%CIHelp line for OVERLAP_DIST
Sets the minimum overlap of successive tool strokes (nibbling sequence).


%CIHelp line for CENTER_RIGHT
Tool's right nose center is used as control point for CL data output.


%CIHelp line for TAPER_ANGLE
Value for machine controlled taper angle.


%CPHelp line for MACHINE_TYPE
Set the Machine type for auxiliary machining sequences.


%CPHelp line for CUT_UNITS
Set the feed rate units used for all cut motions.


%CPHelp line for TRAVERSE_FEED
Set the feed rate for all traverse tool motions.


%CPHelp line for SCAN_TYPE
Select methods of machining area.


%CPHelp line for ROUGH_OPTION
Select from options to specify the use of profiling passes.


%CIHelp line for STEPOVER_ADJUST
STEP_OVER parameter will be adjusted provide complete coverage of region.


%CPHelp line for RETRACT_OPTION
Select whether to minimize the number of tool retracts.


%CIHelp line for TRIM_TO_WORKPIECE
If set to YES mill volume will be confined to workpiece boundaries.


%CLHelp line for INTERSECT_OPTION
INTERSECT_OPTION


%CPHelp line for CUT_DIRECTION
Select from STANDARD or REVERSE to toggle cut direction.


%CLHelp line for CYCLE_TYPE
CYCLE_TYPE


%CPHelp line for CYCLE_OPTIMIZE
Determine whether to combine multiple locations into single cycle.


%CPHelp line for CORNER_TYPE
Set to specify the type of corner created in the tool path.


%CPHelp line for GOUGE_AVOID_TYPE
Determine how much of the tool to use for gouge avoidance.


%CIHelp line for GROOVE_FINISH_TYPE
Allows the creation of an intermediate retract for grooving NC sequences.


%CPHelp line for OUTPUT_TYPE
Specify CYCLE or POINT_BY_POINT output for nibbling NC sequence.


%CIHelp line for APPROXIMATE_SPLINES
Splines will be approximated as a series of arc and line segments.


%CIHelp line for SPINDLE_SENSE
Direction of rotation of the spindle.


%CPHelp line for BLADE_UNITS
Set the units used for BLADE_SPEED parameter.


%CPHelp line for CIRC_INTERPOLATION
Specify the format of CL data generated when machining a circular edge.


%CPHelp line for COOLANT_OPTION
Specify type of coolant flow desired.


%CPHelp line for COOLANT_PRESSURE
Set coolant pressure to HIGH, MEDIUM, LOW, or NONE.


%CPHelp line for CUTCOM
Turn on or off cutter compensation in tool path.


%CPHelp line for CUTCOM_TYPE
Specify the type of moves that will use cutter compensation in tool path.


%CPHelp line for PLUNGE_UNITS
Set feed units used for all plunging motions.


%CIHelp line for LEAD_IN
Enter along an arc to the cut or slice.


%CIHelp line for LEAD_OUT
Exit along an arc to the cut or slice.


%CPHelp line for APPR_EXIT_PATH
Set to control how a sketched approach and exit path are trimmed.


%CIHelp line for CLEARANCE_EDGE
Tool edge to be used for OVERTRAVEL_DISTANCE specification.


%CLHelp line for THREAD_ORIENT
THREAD_ORIENT


%CLHelp line for THREAD_TYPE
THREAD_TYPE


%CPHelp line for OUTPUT_THRD_PNTS
Set to YES to output approach and exit points to CL file.


%CPHelp line for RAPID_FEED_UNITS
Set the units used for all rapid tool motions.


%CLHelp line for PATHS_DIST
PATHS_DIST


%CLHelp line for PATHS_DIST_ADJUST
PATHS_DIST_ADJUST


%CPHelp line for THREAD_FEED_UNITS
Set method of designating thread pitch.


%CIHelp line for ROTATE_MODE
Designating table rotation mode - incremental or absolute.


%CPHelp line for ROTATE_DIRECTION
Set the rotate direction used for table rotations.


%CIHelp line for INCREMENTAL
Designate table rotations to be incremental.


%CIHelp line for ABSOLUTE
Designate table rotations to be absolute.


%CPHelp line for SHORTEST
Move table along the shortest path.


%CPHelp line for CLW
Move table in the clockwise direction.


%CPHelp line for CCLW
Move table in the counter clockwise direction.


%CPHelp line for ONE_PASS_OFFSET
Set the offset for start point of tool path for one pass face milling.


%CIHelp line for ENTRY_EDGE
Tool edge to be used for APPROACH_DISTANCE specification.


%CPHelp line for INITIAL_EDGE_OFFSET
Set the offset for centerline of cutter off initial edge. 


%CPHelp line for FINAL_EDGE_OFFSET
Set the offset for centerline of cutter off the final edge.


%CIHelp line for LOCKED_TOOL_ORIENT
If set only linear entities with orient equal to the value will be machined.


%CPHelp line for PREV_DIAM
Enter the diameter of previous used tool.


%CPHelp line for CORNER_OFFSET
Enter the distance near corner you want to machine.


%CPHelp line for FEED_UNITS
Set the feed rate units.


%CPHelp line for FEED_RATE
Set the feed rate.


%CIHelp line for APPROACH
Approach feed type.


%CIHelp line for EXIT
Exit feed type.


%CIHelp line for PLUNGE
Plunge feed type.


%CIHelp line for CUT
Cut feed type.


%CIHelp line for FREE
Free feed type.


%CIHelp line for APPR_EXIT_EXT
Distance a tool moves beyond walls of the volume


%CIHelp line for 3D_COMPENSATION
Outputs vector information for 3D cutter compensation to the CL file.


%CIHelp line for HOLDER_DIAMETER
The diameter of the tool holder to be used for degouging.


%CPHelp line for END_STOP_CONDITION
Set the option for end stop command.


%CLHelp line for OPSTOP
Output OPSTOP command.


%CLHelp line for PROGRAM_STOP
Output STOP command.


%CIHelp line for ALLOW_NEG_Z_MOVES
Allow moves in negative Z direction.


%CIHelp line for CUTLINE_EXT_TYPE
Specifies the type of extensions to be added to the cutlines.


%CPHelp line for BOUNDARY
Extend cutlines to the boundaries of the selected surface quilt.


%CIHelp line for GENRTR_APPROACH
WEDM power setting used for approach moves.


%CIHelp line for REGISTER_TABLE
Filename of the table containing register information.


%CIHelp line for CHAMFER_DIM
Length of chamfer segment if chamfers are set as cut motion corner conditions.


%CIHelp line for USE_SRF_NORM
Determines if surface normals are used as the reference for axis definition.


%CPHelp line for AUTO_SYNCHRONIZE
Automatically synchronize cutlines in addition to user defined synchronization.


%CIHelp line for CORNER_FINISH_TYPE
Specifies the type of corner that is created between two straight segments.


%CPHelp line for AUTO_INNERCUTLINE
Use inner edges as inner cutlines.


%CPHelp line for HOLDER_LENGTH
Specify length of the tool holder.


%CPHelp line for USE_SURF_NORMS
Compute tool axis definition with respect to surface normals.


%CPHelp line for IGNORE_SURF_NORMS
Compute tool axis definition without respect to surface normals.


%CIHelp line for 4X_TILT_ANGLE
Tool angle from 4 axis plane.


%CIHelp line for 4X_LEAD_ANGLE
Tool orientation angle along cut direction.


%CIHelp line for 4X_MIN_LEAD_ANGLE
Minimum allowable tool orientation angle along cut direction.


%CIHelp line for 4X_MAX_LEAD_ANGLE
Maximum allowable tool orientation angle along cut direction.


%CPHelp line for 4X_LEAD_RANGE_OPT
Adjust lead angle of the tool.


%CPHelp line for ARC_FEED_CONTROL
Refer arc feed to center or perimeter of tool.


%CIHelp line for TOOL_CENTER
Arc feed is calculated with respect to tool center.


%CIHelp line for TOOL_PERIMETER
Arc feed is calculated with respect to tool edge.


%CIHelp line for CHK_SRF_STOCK_ALLOW
Amount of material left on check surfaces after milling completed.


%CIHelp line for APPROACH_TYPE
Approach motion type for thread milling


%CPHelp line for EXIT_TYPE
Exit motion type for thread milling


%CPHelp line for RADIAL
Radially Approach/Exit the tool path