msgtxt_dial.txt
来自「proe5.0野火版下载(中文版免费下载)」· 文本 代码 · 共 3,234 行 · 第 1/5 页
TXT
3,234 行
%CPHelp line for ONTurn the option ON.%CPHelp line for OFFTurn the option OFF.%CIHelp line for MACHINE_IDThe ID number of the machine to be used in the NC sequence.%CIHelp line for MACH_NAMEThe name of the machine to be used in the CL data MACHIN statement.%CIHelp line for MACH_IDThe ID number of the machine used in the CL data MACHIN statement.%CIHelp line for NCL_FILEThe name given the Cutter Location (CL) file generated.%CIHelp line for PRE_MACHINING_FILEFile to be included prior to CL file contents.%CIHelp line for POST_MACHINING_FILEFile to be appended to CL file contents.%CIHelp line for MILLSets orientation of tool path to X, Y plane (AUX. PROGRAMMING ONLY).%CIHelp line for TURNSets orientation of tool path to X, Z plane (AUX. PROGRAMMING ONLY).%CIHelp line for CUT_FEEDFeed rate for all NC sequence cutting motions in CUT_UNITS.%CIHelp line for ARC_FEEDFeed rate for all cutting moves along an arc in CUT_UNITS.%CIHelp line for FREE_FEEDFeed rate for traverse (non-cutting) motions in RETRACT_UNITS.%CIHelp line for RETRACT_FEEDFeed rate at which the cutter moves away from the workpiece in RETRACT_UNITS.%CIHelp line for FPMSets feed rate units to FEET PER MINUTE.%CIHelp line for IPMSets feed rate units to INCHES PER MINUTE.%CIHelp line for MMPMSets feed rate units to MILLIMETERS PER MINUTE.%CIHelp line for FPRSets feed rate units to FEET PER REVOLUTION.%CIHelp line for IPRSets feed rate units to INCHES PER REVOLUTION.%CIHelp line for MMPRSets feed rate units to MILLIMETERS PER REVOLUTION.%CPHelp line for THREAD_FEEDSet the value of thread pitch in THREAD_FEED_UNITS.%CPHelp line for TPISet thread feed to THREADS PER INCH%CPHelp line for FLOAT_TAP_FACTORSet value to adjust THREAD_FEED for floating tap applications.%CIHelp line for TRAVERSE_UNITFeed rate for traverse (non-cutting) motions in RETRACT_UNITS.%CIHelp line for TYPE_1Lace type tool path where cutter retracts upon encountering an island.%CIHelp line for TYPE_2Lace type tool path where the cutter will go around islands.%CIHelp line for TYPE_3Lace type tool path where cutter will machine zone by zone.%CIHelp line for TYPE_SPIRALGenerates a spiral tool path around all islands.%CEHelp line for TYPE_ONE_DIRTool will cut in one direction only, retracting and traversing to next cut.%CIHelp line for PICK_ORDERSets the machining order for holemaking to the hole selection order.%CIHelp line for TYPE_1_CONNECTTool will follow part contour when entering and exiting each cut.%CIHelp line for ROUGH_ONLYTool path will clear area of each slice without profiling boundaries.%CIHelp line for ROUGH_&_PROFTool path will clear each slice then profile the boundaries.%CIHelp line for PROF_&_ROUGHTool path will first profile slice boundaries and then clear area.%CWHelp line for PROF_ONLYTool path will only profile each slice's boundaries.%CIHelp line for NOTurn option OFF.%CPHelp line for YESTurn option ON.%CIHelp line for UPCUTDetermines cut direction such that cutter will push away from wall.%CIHelp line for CLIMBDetermines cut direction such that cutter will climb wall.%CIHelp line for OPTIMIZENumber of retracts between cuts will be minimized.%CWHelp line for NOT_OPTIMIZETool may retract between cuts.%CIHelp line for WORKPIECEThe piece of material upon which all machining NC sequences are performed.%CIHelp line for REF_PARTThe design part referenced by machining NC sequences.%CIHelp line for STANDARDSets the cut direction to the system generated default.%CIHelp line for REVERSEReverses the cut direction from the system generated default.%CIHelp line for LINE_CONNECTMoves tool in a straight line from end of a slice to the start of a new slice.%CIHelp line for CURVE_CONNECTCutter follows geometry when moving from end of slice to start of new slice.%CIHelp line for TAPSets the COOLANT_OPTION to tap setting.%CIHelp line for FILLETCreates corner by connecting two straight segments with an arc.%CPHelp line for STRAIGHTCreate a corner by extending straight segments until intersection.%CIHelp line for CENTERCenter of tool nose radius is used as control point for CL data output.%CIHelp line for TIPTool control point used for CL output is offset by nose radius.%CIHelp line for X_OFFSETOutput point offset to the along machine X Axis by nose radius.%CIHelp line for Z_OFFSETOutput point offset along machine Z Axis by nose radius.%CIHelp line for TIP_AND_SIDESTool path avoids gouging considering entire length of tool.%CEHelp line for CONTINUOUSTool path for groove finishing will not retract.%CIHelp line for NO_BACKCUTTool path for groove finishing will plunge both sides of groove.%CIHelp line for MULTAX_DATAControl format of CL data to include i,j,k axis vectors.%CIHelp line for TRANS_ROTABLControl format of CL data to include rotations about a,b,c axes.%CIHelp line for POINT_BY_POINTCL data will include each position as separate GOTO.%CIHelp line for CYCLE_NIBBLECL data will include nibbling cycle statements to use canned cycles.%CPHelp line for COUPLETSet the output format for holemaking to ISO standard couplets.%CPHelp line for FIXEDSet the output format for holemaking to fixed format.%CPHelp line for STEP_DEPTHSet the incremental depth of each cut.%CPHelp line for END_STEP_DEPTHInterpolate step value between STEP_DEPTH and END_STEP_DEPTH (if set).%CPHelp line for TOLERANCESet max. allowable deviation from model geometry in tool path. %CPHelp line for STEP_OVERSet the distance between passes for milling or between hits for area nibble.%CPHelp line for NUMBER_PASSESSet the number passes per slice for the slice (in lieu of STEP_OVER).%CIHelp line for NUM_PROF_PASSESSets the number of passes for profiling.%CIHelp line for PROF_INCREMENTSets the horizontal distance between profiling passes.%CIHelp line for ROUGH_STOCK_ALLOWAmount of stock left by roughing portion of the tool path.%CIHelp line for BOTTOM_STOCK_ALLOWAmount of stock left on surfaces parallel to the retract plane.%CPHelp line for MAX_SCALLOP_HGTControl tool step by specifying the maximum allowable scallop on surfaces.%CPHelp line for WALL_SCALLOP_HGTControl tool step by specifying the maximum allowable scallop on walls.%CPHelp line for BOTTOM_SCALLOP_HGTControl tool step by specifying the maximum allowable scallop on bottom.%CPHelp line for SCALLOP_HGTControl tool step by specifying the maximum allowable scallop.%CPHelp line for AXIS_SHIFTShift the tool along its axis (+ is away from spindle).%CPHelp line for CUT_ANGLEChange the angle of cuts relative to the NC Sequence coordinate system.%CIHelp line for LEAD_ANGLETool orientation angle from surface normal along cut direction (+ is forward).%CIHelp line for TILT_ANGLETool angle from surface normal perpendicular to cut direction (+ is right).%CIHelp line for CENTERLINE_OFFSETMoves the tool centerline off the tool path by specified value.%CIHelp line for Z_ALLOW_RATIORatio of the STOCK_ALLOW value to the amount of stock left on faces.%CIHelp line for Z_STOCK_ALLOWSets the amount of stock to be left on faces.%CIHelp line for END_OVERTRAVELDistance automatically added to the tool path in the cut direction.%CPHelp line for CORNER_LENGTHDefine the length of the corner parallelogram in the corner condition.%CPHelp line for CORNER_ANGLEDefine the angle for the corner parallelogram in the corner condition.%CPHelp line for CONCAVE_RADIUSSet the radius for the concave corner condition.%CPHelp line for CONVEX_RADIUSSet the radius for the convex corner condition.%CIHelp line for SIDEWALL_OFFSETThe distance tool will stop from the opposite wall before retracting. %CIHelp line for PECK_DEPTHSets incremental depth for each pass in holemaking and groove turning.%CIHelp line for BREAKOUT_DISTANCEValue to be added to the depth of all holes drilled using THRU ALL.%CIHelp line for CSINK_DIAMTool motion depth is computed to create countersink of CSINK_DIAM.%CIHelp line for SHAKEAWAY_DISTMaterial left for shakeaway in contouring or nibble edge NC sequence.%CIHelp line for BURN_IN_OFFSETAmount to offset tool path start point for material piercing. %CEHelp line for OVERHANG_DISTMinimum distance tool path will extend past specified overhang points.%CPHelp line for GROOVE_DEPTHSet the depth of cut for grooving NC Sequence. %CPHelp line for STOP_DISTPlace OPSTOP in CL data at STOP_DIST back from start point.%CIHelp line for REVERSE_DISTFor multiple profile passes, distance from start point for direction reversal.%CIHelp line for ATTACH_WIDTHMoves wire parallel to cut from start hole before entering cut.%CIHelp line for BACK_CLEAR_ANGLEClearance angle between the back of the tool and the remaining stock.%CIHelp line for SPINDLE_SPEEDSets the rate at which the spindle turns.%CIHelp line for CWSpindle will turn clockwise.%CIHelp line for CCWSpindle will turn counterclockwise.%CIHelp line for MAX_SPINDLE_RPMLimits maximum spindle RPM by placing a MAXRPM in the CL file SPINDL statement.%CIHelp line for CONST_RPMSpeed setting where the rotations per minute is constant.%CIHelp line for CONST_SFMSpeed setting where the surface feet per minute is constant.%CIHelp line for CONST_SMMSpeed setting where the surface meters per minute is constant.%CIHelp line for NO_RANGESpecifies that there is no spindle speed range.%CIHelp line for NUMBERSpecifies that the spindle speed is set by a number.%CPHelp line for RANGE_NUMBERSpecify the spindle range number to be used.%CIHelp line for BLADE_SPEEDSets the rate at which EDM wire is spooled.%CIHelp line for LINTOLSpecifies the interpolation used by the post processor for MULTAX sequences.%CWHelp line for POINTS_ONLYCL file output will not include circular interpolation, only points.%CIHelp line for POINTS_&_ARCOutput circle statement and maximum number of points for arcs in CL data.%CIHelp line for ARC_ONLYOutput circle statement and minimum number of points for arcs in CL data.%CIHelp line for APT_FORMATSetting for post processors requiring CIRCLE statements in the APT format.%CIHelp line for NUMBER_OF_ARC_PTSNumber of arc points output to CL file if CIRC_INTERPOLATION is ARC_ONLY.%CIHelp line for FLOODCOOLANT_OPTION that floods workpiece with coolant.%CIHelp line for MISTCOOLANT_OPTION to produce a MIST.%CIHelp line for THRUCOOLANT_OPTION for through spindle coolant.%CIHelp line for ALL_MOVESCUTCOM will be turned on at beginning of tool path and off at end.%CIHelp line for NO_Z_MOVESCUTCOM is turned off for all moves in the Z direction.%CEHelp line for PROF_MOVES_ONLYCutter compensation is applied for profiling moves only.%CPHelp line for CUTCOM_REGISTERSpecify the number of controller register that holds tool compensation data.%CIHelp line for CUTCOM_REG_STARTInitial cutter compensation controller register number.%CIHelp line for CUTCOM_REG_INCRValue the CUTCOM register will increment during a multi-pass WEDM tool path.%CIHelp line for CUTCOM_REG_RIGHTCutter compensation register for right tool radius.%CPHelp line for FIXT_OFFSET_REGSpecify predefined fixture offset register.%CPHelp line for DELAYSet dwell time for cutter at bottom of the cut.%CIHelp line for SECONDSTime in seconds.%CPHelp line for REVSet the number of revolutions to dwell at the bottom of the cut. %CIHelp line for SPARK_ALLOWAmount of additional tool path offset to account for spark thickness.%CPHelp line for TOOL_ORIENTSet angular orientation of tool relative to tool and sequence csys.%CIHelp line for REQ_MACHINE_POWERSets the machine power required.%CIHelp line for AMPERESSets the Amperes for plasma contouring.%CIHelp line for VOLTSSets the Volts for plasma contouring.%CIHelp line for TOOL_ORIENTATIONOrientation of turning tool relative to machine Z axis.%CPHelp line for CL_DISTEstablish upper wire guide height from top of part.%CIHelp line for GENRTR_ROUGHWEDM power setting used for rough cuts.%CIHelp line for GENRTR_DETACHWEDM power setting used for detachment moves. %CIHelp line for GENRTR_FINISHWEDM power setting used for finish cut moves. %CIHelp line for GENRTR_REG_INCRAmount to increment the generator register between passes.%CPHelp line for APPROACH_FEEDSet the rate at which the cutter approaches the workpiece.%CIHelp line for EXIT_FEEDRate a which the cutter leaves the work surface.%CPHelp line for PLUNGE_FEEDSet the rate for all plunging moves.%CIHelp line for RAMP_ANGLEThe angle the tool enters the workpiece during a plunge move.%CIHelp line for RAMP_FEEDFeed rate used during ramping movements.%CIHelp line for CLEAR_DISTDistance needed to completely clear the workpiece prior to retraction.%CIHelp line for INTER_RET_HEIGHTDistance the mill retracts in between passes.%CPHelp line for FULL_RETRACT_DEPTHSet the distance of full retraction for the chip breaking cycle.%CIHelp line for RAPTO_DISTAllows for rapid advancement from the clear distance to the top of the hole.%CPHelp line for ORIENT_ANGLESpecify the orientation of the boring bar before moving away, prior to retract.%CIHelp line for JOG_DISTDistance boring bar is backed away from the wall before retracting.%CPHelp line for LEAD_RADIUSSet the radius of the tangent circle motion for leading in or out.%CPHelp line for LEAD_STEPSet the linear length of the step portion of the lead in/out motion.%CIHelp line for CLEARANCE_OFFSETSets how much the tool retracts before moving on to the next hole.%CIHelp line for RETRACT_RATIOAmount of retraction that occurs during area turning as a ratio of STEP_DEPTH.%CPHelp line for PLUNGE_ANGLESet the angle of the tool motion to enter the material.%CIHelp line for PULLOUT_ANGLEAngle at which the tool is pulled away from the workpiece.%CPHelp line for TRIM_BOTHTrim both the sketched entry and exit trajectories by the tool path.%CPHelp line for TRIM_APPROACHTrim the sketched entry trajectory by the tool path.%CPHelp line for TRIM_EXITTrim the sketched exit trajectory by the tool path.⌨️ 快捷键说明
复制代码Ctrl + C
搜索代码Ctrl + F
全屏模式F11
增大字号Ctrl + =
减小字号Ctrl + -
显示快捷键?