msgtxt_inf.txt

proe5.0野火版下载(中文版免费下载)

%CI  %0s edges shown shorter than %1s
  %0s edges shown shorter than %1s
  %0s 边显示比%1s 短.

%CI%0d reflection curves were constructed.
%0d reflection curves were constructed.
构建了%0d反射曲线.

%CECannot find an edge sufficiently close to this one.
Cannot find an edge sufficiently close to this one.
不能找到足够的边将其封闭。

%CPEnter the number of light sources in the direction of the arrow [%0d]:
Enter the number of light sources in the direction of the arrow|||%0d
输入在箭头所指的方向的光源数:|||%0d

%CPEnter the number of light sources in the opposite direction [%0d]:
Enter the number of light sources in the opposite direction|||%0d
输入反向的光源数:|||%0d

%CILight sources generated: dist = %0f, first = %1f, last = %2f.
Light sources generated: dist = %0f, first = %1f, last = %2f.
生成的光源:距离 = %0f, 起始 = %1f, 终止 = %2f.

%CIMinimal radius of curvature: %0s
Minimal radius of curvature: %0s
最小的曲率半径: %0s

%CIMinimal radiuses of curvature: (red point) %0s     (blue point) %1s
Minimal radii of curvature: (red point) %0s     (blue point) %1s
最小的曲率半径: (红色点) %0s     (兰色点) %1s

%CINo edges found shorter than %0s
No edges found shorter than %0s
没有发现比%0s 短的边.

%CPSelect a plane of light source(s).
Select a plane of light source(s).
选取一个光源平面。

%CPSelect a spline entity to show deviation.
Select a spline entity to show deviation.
选取要显示偏差的样条图元。

%CPSelect quilt of which to compute smallest positive radius of curvature.
Select quilt of which to compute smallest positive radius of curvature.
选取面组计算最小的曲率半径.

%CPSelect surface of which to compute smallest positive radius of curvature.
Select surface of which to compute smallest positive radius of curvature.
选取曲面计算最小的正曲率半径.

%CPSpecify distance between light sources []:
Specify distance between light sources
指定光源间的距离:

%CPSpecify the number of light sources [%0d]:
Specify the number of light sources|||%0d
指定光源数|||%0d

%CIDihedral angle output to file %0w.
Dihedral angle output to file %0w.
二面角输出到文件%0w。

%CIThe information about dihedral angle has been written to file %0w.%1d
The information about dihedral angle has been written to file %0w.%1d
关于二面角的信息已经写入文件%0w.%1d。

%CIThe information about dihedral angle will be written to file %0w.%1d
The information about dihedral angle will be written to file %0w.%1d
关于二面角的信息将写入文件%0w.%1d。

%CIThe dihedral angle at length ratio %0s is %1s.
The dihedral angle at length ratio %0s is %1s.
在长度比例%0s的二面角为%1s。

%CIMax dihedral angle of %0s degrees is reached at length ratio %1s.
Max dihedral angle of %0s degrees is reached at length ratio %1s.
%0s度的最大二面角达到长度比例%1s。

%CIMin dihedral angle of %0s degrees is reached at length ratio %1s.
Min dihedral angle of %0s degrees is reached at length ratio %1s.
%0s度的最小二面角达到长度比例%1s。

%CPSelect an edge along which the dihedral angles will be computed.
Select an edge along which the dihedral angles will be computed.
选取将沿之计算二面角的边。

%CEEdges are not aligned.
Edges are not aligned.
边没有对齐。

%CLREFERENCE ASSEMBLIES: 
REFERENCE ASSEMBLIES: 
参照组件: 

%CLREFERENCE PARTS: 
REFERENCE PARTS: 
参照零件: