config.h

intel xscale 425的bsp源码

#define ROM_FLASH_RESERVED	(8* 0x00100000)		/* Size of Flash dev reserved from top */
#define ROM_ACTUAL_FLASH_SIZE   (16 * 0x00100000) /* Real size of Flash */

#define ROM_BASE_ADRS       0x50000000            /* base of writable Flash */
#define ROM_SIZE            0x01000000	          /* size - start */
                                        
#define ROM_COPY_SIZE       ((ROM_SIZE - 0x2000) / 4)
#define ROM_SIZE_TOTAL      ROM_SIZE              /* total size of Flash ROM */
#define BOOT_ROM_RELOCATE_SIZE (0x00200000)

/*
 * The size must be big enough so that
 *    (ROM_BASE_ADRS + ROM_SIZE - ROM_TEXT_ADRS) >= size of boot image
 * We allow up to an arbitrary 128K for the image.
 */
#if (ROM_BASE_ADRS + ROM_SIZE - ROM_TEXT_ADRS) < 0x20000 
  #error  ROM_ values need checking in config.h/Makefile  
#endif /* (ROM_BASE_ADRS + ROM_SIZE - ROM_TEXT_ADRS) < 0x20000 */

#define FLASH_BASE          ROM_FLASH_ALT_BASE
#define	INCLUDE_FLASH_NO2			/* 增加第二块flash的宏,如果无第二块则注释掉 by luhb 2007-03-20 */



/*
 * Where the text starts in ROM, (address of _romInit), normally it will be,
 * MMU_TRANSLATION_BASE + 16K + additional 1K if we are using second level
 * translation tables.
 *
 * ROM_TEXT_ADRS = MMU_TRANSLATION_BASE + 0x4000  (+ 0x400 if second level page
 *						    table used)
 */
/* Where the text starts in ROM */
#define ROM_TEXT_ADRS      0x50001000

/*
 * ISR_STACK_SIZE is defined here rather than in ../all/configAll.h (as is
 * more usual) because the stack size depends on the interrupt structure of the
 * BSP.
 */
 #define ISR_STACK_SIZE		0x1000	 /* ISR Stack Size 16 */

 #undef STACK_SAVE
 #define STACK_SAVE	 1024		 /* maximum size of stack preserved */

 #define SIZE_OF_IP_ADDRESS 24
 #define SIZE_OF_MAC_ADDRESS 6

 #define NV_BOOT_LINE_SIZE		(0x100)
 #define NV_GENERIC_STORAGE_AREA_SIZE	(0x100)

 /* 
  * These defines specify where the vxWorks bootline and end device information
  * for the board is to be stored. They are mutually exclusive and should not be
  * defined together.
  */
#undef USE_EEPROM_STORAGE	/* Define this to enable eeprom as NVRAM - See ixdp425.html */
#define USE_FLASH_STORAGE       /* Define this to enable FLASH as NVRAM */

#if !defined(USE_EEPROM_STORAGE) && !defined(USE_FLASH_STORAGE)
#error "You must specify either EEPROM or FLASH for NVRAM storage"
#endif

#if defined(USE_EEPROM_STORAGE) && defined(USE_FLASH_STORAGE)
#error "You cannot specify both EEPROM and FLASH for NVRAM storage"
#endif

/*
  *
  * The diagram below shows the EEPROM when used as NVRAM storage.
  * 
  +----+ Top of 512byte EEPROM.
  |    |
  |    |  MAC address storage.
  |____|_ EEPROM + 256 Bytes	-- NV_GENERIC_STORAGE_AREA
  |    |
  |    |  Boot Line Storage
  |    |
  +----+ Bottom of EEPROM	-- sysNvRamGet/sysNvRamGet - Allows access to here to 
  *
  */

 #define INCLUDE_FLASH

 #ifdef INCLUDE_FLASH   
  #define FLASH_WIDTH		2
  #define FLASH_WIDTH_SPECIAL_2     /* Special definition for Word based flash devices */
  #define SYS_FLASH_TYPE		FLASH_28F128J3A	/* Specify 16 bit 28F part */
  #define FLASH_SEGMENT_SIZE		(128 * 1024)		/* sector size of E28F128J3 */
  #define FLASH_ADRS			(ROM_FLASH_ALT_BASE + ROM_ACTUAL_FLASH_SIZE - FLASH_SEGMENT_SIZE) 
  #define FLASH_SIZE			FLASH_SEGMENT_SIZE 

  #ifdef USE_FLASH_STORAGE
    #define NV_RAM_SIZE			FLASH_SEGMENT_SIZE
    #undef  NV_BOOT_OFFSET
    #define NV_BOOT_OFFSET		(FLASH_SEGMENT_SIZE - NV_BOOT_LINE_SIZE - NV_GENERIC_STORAGE_AREA_SIZE) /* BootLine Support */
  #endif /* USE_FLASH_STORAGE */

  #define SYS_FLASH_WRITE
  #undef FLASH_NO_OVERLAY  
 #else  /* INCLUDE_FLASH */
  #define NV_RAM_SIZE		NONE
 #endif /* INCLUDE_FLASH */

#define INCLUDE_EEPROM

#ifdef INCLUDE_EEPROM
  #ifdef USE_EEPROM_STORAGE
     #define NV_RAM_SIZE (0x200)
  #endif /* USE_EEPROM_STORAGE */
#endif /* INCLUDE_EEPROM */

/* Allocation of Generic NV storage area */  
#if defined(INCLUDE_FLASH) || defined(INCLUDE_EEPROM)
  #define NV_RAM_IF_START_OFFSET        (NV_GENERIC_STORAGE_AREA_SIZE)
  #define NV_MAC_ADDR_POOL		(NV_GENERIC_STORAGE_AREA_SIZE)		 /* Used as offset of sysNvRamGet/Set */
  #define NV_MAC_ADRS_NPE1		(NV_MAC_ADDR_POOL)
  #define NV_MAC_ADRS_NPE2		(NV_MAC_ADRS_NPE1 + SIZE_OF_MAC_ADDRESS)

  /* 
   * Most PCI NICS will store their own MAC address but we include room for them
   * here in case they don't.
   */
  #define NV_MAC_ADRS_PCIEND1		(NV_MAC_ADRS_NPE2 + SIZE_OF_MAC_ADDRESS)
  #define NV_MAC_ADRS_PCIEND2		(NV_MAC_ADRS_PCIEND1 + SIZE_OF_MAC_ADDRESS)
  #define NV_MAC_ADRS_PCIEND3		(NV_MAC_ADRS_PCIEND2 + SIZE_OF_MAC_ADDRESS)
  #define NV_MAC_ADRS_PCIEND4		(NV_MAC_ADRS_PCIEND3 + SIZE_OF_MAC_ADDRESS)

  #define NV_IP_ADRS_RESERVED           (NV_MAC_ADRS_PCIEND4 + SIZE_OF_MAC_ADDRESS)
  #define NV_IP_ADRS_NPE1               (NV_IP_ADRS_RESERVED + SIZE_OF_IP_ADDRESS)
  #define NV_IP_ADRS_NPE2               (NV_IP_ADRS_NPE1 + SIZE_OF_IP_ADDRESS)
  #define NV_IP_ADRS_PCIEND1            (NV_IP_ADRS_NPE2 + SIZE_OF_IP_ADDRESS)
  #define NV_IP_ADRS_PCIEND2            (NV_IP_ADRS_PCIEND1 + SIZE_OF_IP_ADDRESS)
  #define NV_IP_ADRS_PCIEND3            (NV_IP_ADRS_PCIEND2 + SIZE_OF_IP_ADDRESS)
  #define NV_IP_ADRS_PCIEND4            (NV_IP_ADRS_PCIEND3 + SIZE_OF_IP_ADDRESS)
   
  #define NV_RAM_IF_END_OFFSET          (NV_IP_ADRS_PCIEND4 + SIZE_OF_IP_ADDRESS)
  #define NV_RAM_IF_SIZE                (NV_RAM_IF_END_OFFSET - NV_RAM_IF_START_OFFSET)   


#endif /* defined(INCLUDE_FLASH) || defined(INCLUDE_EEPROM) */

#define INCLUDE_END			/* Enable END drivers */

#define INCLUDE_PCI			/* enable PCI Bus */
#ifdef INCLUDE_PCI
#define INCLUDE_PCI_DMA
#endif /* INCLUDE_PCI */

#ifdef INCLUDE_END			/* If END drivers are enabled */

#define INCLUDE_FEI82557END		/* Enable Intel PCI based 8255x driver */

#ifdef INCLUDE_FEI82557END

#ifndef INCLUDE_PCI			/* Cannot have fei without pci */
#undef INCLUDE_FEI82557END
#endif /* INCLUDE_PCI */

#undef INCLUDE_AR521X_END     /* Enable Atheros AR521x wireless WLAN driver */

#ifdef INCLUDE_AR521X_END
#  define DOT11_DEFAULT_SSID "wls"
#  define DOT11_DEFAULT_MODE DOT11_MODE_ESS
#endif /*INCLUDE_AR521X_END*/


#define IXDP_FEIEND_USE_NVRAM_IP	/* Get unassigned FEI IP addresses from NVRAM/EEPROM */
#define IXP425_MAX_FEI_DEVS IXP425_MAX_PCI_DEVS

#define IXDP_FEI557_IP0_DEFAULT		"192.168.10.1"    /* Default address for PORT0 */
#define IXDP_FEI557_IP1_DEFAULT		"192.168.20.1"    /* Default address for PORT0 */
#define IXDP_FEI557_IP2_DEFAULT		"192.168.30.1"    /* Default address for PORT0 */
#define IXDP_FEI557_IP3_DEFAULT		"192.168.40.1"    /* Default address for PORT0 */

#    define PCI_ID_I82557          0x10308086  /* Id for Intel 82557 */
#    define PCI_ID_I82559          0x12298086  /* Id for Intel 82559 */
#    define PCI_ID_I82559ER        0x12098086  /* Id for Intel 82559 ER */

#    define FEI_LOAD_STRING ""             /* created in sysFei82557EndLoad */
#    define FEI_BUFF_LOAN   1

#endif /* INCLUDE_FEI82557END */

#ifdef INCLUDE_IXETHACCEND

#define INCLUDE_RFC_2233

#ifdef INCLUDE_RFC_2233
#undef  END_POLL_STATS_ROUTINE_HOOK
#define END_POLL_STATS_ROUTINE_HOOK m2PollStatsIfPoll
#endif /*INCLUDE_RFC_2233*/

/* leave undefined since hardware does 60 bytes TX padding */
#undef  INCLUDE_IXETHACC_64BYTES_PADDING

#define INCLUDE_IXETHACC_POLL_MODE
#define IXDP_ETHACC_POLL_TICKS_PER_SECOND 1000

/* leave undefined unless the livelock prevention dispatcher is required */ 
#undef INCLUDE_IX_QMGR_LLP_DISPATCHER 

#define INCLUDE_IXETHACC_PORT0_END	/* enable eth phys port 0 */
#define INCLUDE_IXETHACC_PORT1_END	/* enable eth phys port 1 */

/* If IXETH_INIT_WITH_OTHER_FLAG is defined, you can specify "ixe"
 * as the bootline "other" flag to initialize it
 */
#define IXETH_INIT_WITH_OTHER_FLAG

#define IXDP_ETHACC_USE_NVRAM_MAC /* Get MAC addresses via NVRAM/EEPROM */

#define IXDP_ETHACC_IP0_DEFAULT		"192.168.50.1"    /* Default address for PORT0 */
#define IXDP_ETHACC_IP1_DEFAULT		"192.168.60.1"    /* Default address for PORT1 */

/* The following IXETH and EthAcc defines are always defined */
#define IXETHACC_MBLKS 120		/* Number of allocated mBlks per IxEth */

#define INCLUDE_IXETHDB                 /* Enable or disable h/w ethernet database */
#undef  INCLUDE_IXCRYPTO                /* Disable hardware accelerated cryptography by default */


#endif /* INCLUDE_IXETHACCEND */

/* Define INCLUDE_USER_APPL to enable Init of all network devices */
#define INCLUDE_USER_APPL

/* This is the entry point into the IXP425 Application software */
#define USER_APPL_INIT {void ixdp425AppInit(); ixdp425AppInit();}
#define INCLUDE_PING

#endif /* INCLUDE_END */

#undef INCLUDE_USB                  /* USB support */

#ifdef  INCLUDE_USB

/* USB support */
 
/* USB Host Components */
 
#   undef  INCLUDE_USB_INIT             /* USB Initialization */
#   define INCLUDE_UHCI                 /* UHCI Controller Driver */
#   undef  INCLUDE_UHCI_INIT            /* UHCI Initialization */
#   undef  INCLUDE_OHCI                 /* OHCI Controller Driver */
#   undef  INCLUDE_OHCI_INIT            /* OHCI Initialization */
#   undef  INCLUDE_OHCI_PCI_INIT        /* OHCI PCI Initialization */
#   define INCLUDE_USBTOOL              /* usbTool Application */
#   undef  INCDLUE_USB_AUDIO_DEMO       /* USB Audio Demo */
#   define INCLUDE_USB_MOUSE            /* USB Mouse Driver */
#   undef  INCLUDE_USB_MOUSE_INIT       /* Mouse Driver Initialization */
#   define INCLUDE_USB_KEYBOARD         /* USB Keyboard Driver */
#   undef  INCLUDE_USB_KEYBOARD_INIT    /* Keyboard Driver Initialization */
#   define INCLUDE_USB_PRINTER          /* USB Printer Driver */
#   undef  INCLUDE_USB_PRINTER_INIT     /* Printer Driver Initialization */
#   define INCLUDE_USB_SPEAKER          /* USB Speaker Driver */
#   undef  INCLUDE_USB_SPEAKER_INIT     /* Speaker Driver Initialization */
#   undef  INCLUDE_USB_MS_BULKONLY      /* USB Bulk Driver */
#   undef  INCLUDE_USB_MS_BULKONLY_INIT /* Bulk Driver Initialization */
#   undef  INCLUDE_USB_MS_CBI           /* USB CBI Driver */
#   undef  INCLUDE_USB_MS_CBI_INIT      /* CBI Driver Initialization */
#   undef  INCLUDE_USB_PEGASUS_END      /* USB Pegasus Network Driver */
#   undef  INCLUDE_USB_PEGASUS_END_INIT /* Pegaus Driver Initialization */
 
/*  USB Parameters */
 
#   define BULK_DRIVE_NAME "/bd"                /* Bulk Drive Name */
#   define CBI_DRIVE_NAME "/cbid"               /* CBI Drive Name */
#   define PEGASUS_IP_ADDRESS "90.0.0.3"        /* Pegasus IP Address */
#   define PEGASUS_DESTINATION_ADDRESS "90.0.0.53" /* Pegasus Destination Addres
s */
#   define PEGASUS_NET_MASK 0xffffff00          /* Pegasus Net Mask */
#   define PEGASUS_TARGET_NAME "host"           /* Pegasus Target Name */
 
#endif /*INCLUDE_USB*/


/*
 * Strictly optional components which can be removed at will
 */
#undef INCLUDE_FASTPATH /* Includes PNE2.0 fastPathLib */

#if 0
#define INCLUDE_SHELL
#define INCLUDE_RLOGIN
#define INCLUDE_NET_INIT
#define INCLUDE_SHOW_ROUTINES
#define INCLUDE_NET_SHOW
#define INCLUDE_ARP_API
#define INCLUDE_BSD
#define INCLUDE_PING
#define INCLUDE_DEBUG
#define INCLUDE_LOADER
#define INCLUDE_UNLOADER
#define INCLUDE_NET_REM_IO      /* network remote file i/o driver */
#define INCLUDE_MCAST_ROUTING
#define INCLUDE_IP_FILTER
#define INCLUDE_TELNET
#define INCLUDE_NET_HOST_SETUP
#define INCLUDE_NET_SYM_TBL
#define INCLUDE_STAT_SYM_TBL
#define INCLUDE_SYM_TBL

#define INCLUDE_NET_IF_SHOW
#define INCLUDE_NET_ROUTE_SHOW
#define INCLUDE_ICMP_SHOW
#define INCLUDE_NET_IF_SHOW
#define INCLUDE_NET_HOST_SHOW
#define INCLUDE_NET_ROUTE_SHOW
#define INCLUDE_ICMP_SHOW
#define INCLUDE_IGMP_SHOW
#define INCLUDE_TCP_SHOW
#define INCLUDE_UDP_SHOW

#endif

#define makeVxWorks	1	/*donleo*/
#if makeVxWorks
#define INCLUDE_SYM_TBL
#define INCLUDE_SYM_TBL_INIT
#define INCLUDE_STANDALONE_SYM_TBL
#define INCLUDE_SHELL
#define INCLUDE_NET_SHOW
#define INCLUDE_TASK_SHOW
#define INCLUDE_USER_APPL
#define INCLUDE_TFFS	/*donleo*/
#define INCLUDE_DOSFS		/* dosFs file system */
#define INCLUDE_TFFS_SHOW	

#endif

/* For BSP Validation Test Suite */
#undef BSP_VTS
#ifdef BSP_VTS
/***************************************************
 * Add these defines for the Validation Test Suite *
 ***************************************************/
#define INCLUDE_SHELL
#define INCLUDE_RLOGIN
#define INCLUDE_SHOW_ROUTINES
#define INCLUDE_NET_SYM_TBL
#define INCLUDE_LOADER

#define INCLUDE_PING
#define INCLUDE_NET_SHOW
#endif /*BSP_VTS*/

#ifdef __cplusplus
}
#endif


#endif	/* INCconfigh */

#if defined(PRJ_BUILD)
 #include "prjParams.h"
#endif