loader.s

用开源软件自己动手写操作系统的源码,在linux下面实现

/* chapter3/1/loader.S

   Author: Wenbo Yang <[e-mail]> <http://solrex.cn>

   This file is part of the source code of book "Write Your Own OS with Free
   and Open Source Software". Homepage @ <http://share.solrex.cn/WriteOS/>.

   This file is licensed under the GNU General Public License; either
   version 3 of the License, or (at your option) any later version. */

#include "pm.h"

.code16
.text
    jmp LABEL_BEGIN     /* jump over the .data section. */

/* NOTE! Wenbo-20080512: Actually here we put the normal .data section into
   the .code section. For application SW, it is not allowed. However, we are
   writting an OS. That is OK. Because there is no OS to complain about
   that behavior. :) */

/* Global Descriptor Table */
LABEL_GDT:          Descriptor  0,                        0, 0
LABEL_DESC_CODE32:  Descriptor  0,       (SegCode32Len - 1), (DA_C + DA_32)
LABEL_DESC_VIDEO:   Descriptor  0xB8000,             0xffff, DA_DRW

.set GdtLen, (. - LABEL_GDT)  /* GDT Length */

GdtPtr: .2byte  (GdtLen - 1)  /* GDT Limit */
        .4byte  0             /* GDT Base */

/* GDT Selector */
.set    SelectorCode32, (LABEL_DESC_CODE32 - LABEL_GDT)
.set    SelectorVideo,  (LABEL_DESC_VIDEO  - LABEL_GDT)

/* Program starts here. */
LABEL_BEGIN:
    mov     %cs, %ax    /* Move code segment address(CS) to data segment */
    mov     %ax, %ds    /* register(DS), ES and SS. Because we have      */
    mov     %ax, %es    /* embedded .data section into .code section in  */
    mov     %ax, %ss    /* the start(metioned in the NOTE above).        */

    mov     $0x100, %sp

    /* Initialize 32-bits code segment descriptor. */
    xor     %eax, %eax
    mov     %cs, %ax
    shl     $4, %eax
    addl    $(LABEL_SEG_CODE32), %eax
    movw    %ax, (LABEL_DESC_CODE32 + 2)
    shr     $16, %eax
    movb    %al, (LABEL_DESC_CODE32 + 4)
    movb    %ah, (LABEL_DESC_CODE32 + 7)

    /* Prepared for loading GDTR */
    xor     %eax, %eax
    mov     %ds, %ax
    shl     $4, %eax
    add     $(LABEL_GDT), %eax      /* eax <- gdt base*/
    movl    %eax, (GdtPtr + 2)

    /* Load GDTR(Global Descriptor Table Register) */
    lgdtw   GdtPtr

    /* Clear Interrupt Flags */
    cli

    /* Open A20 line. */
    inb     $0x92, %al
    orb     $0b00000010, %al
    outb    %al, $0x92

    /* Enable protect mode, PE bit of CR0. */
    movl    %cr0, %eax
    orl     $1, %eax
    movl    %eax, %cr0

    /* Mixed-Size Jump. */
    ljmpl $SelectorCode32, $0       /* Thanks to earthengine@gmail, I got */
                                    /* this mixed-size jump insn of gas.  */

LABEL_SEG_CODE32: 
.code32
    mov     $(SelectorVideo), %ax
    mov     %ax, %gs                /* Video segment selector(dest) */

    movl    $((80 * 10 + 0) * 2), %edi
    movb    $0xC, %ah               /* 0000: Black Back 1100: Red Front */
    movb    $'P', %al

    mov     %ax, %gs:(%edi)

    /* Stop here, infinate loop. */
    jmp     .

/* Get the length of 32-bit segment code. */
.set    SegCode32Len, . - LABEL_SEG_CODE32