main.c

AVR读取SD卡里FAT格式内容的源程序

///////////////////////////////////////////////////////////////////
///////////////////////////////////////////////////////////////////

// This project was designed by Jacky.L (深圳)
// The part of SD and FAT Copyright (c) 2006-2007 by Roland Riegel

///////////////////////////////////////////////////////////////////
///////////////////////////////////////////////////////////////////

/*
 * Copyright (c) 2006-2007 by Roland Riegel <[e-mail]>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#include <string.h>
#include <avr/pgmspace.h>
#include <avr/sleep.h>
#include "fat16.h"
#include "fat16_config.h"
#include "partition.h"
#include "sd_raw.h"
#include "sd_raw_config.h"
#include "uart.h"



#include "R61503b.h"

#define DEBUG 0

uchar tftBuffer[128];


/**
 * \mainpage MMC/SD card example application
 *
 * This project is a small test application which implements read and write
 * support for MMC and SD cards.
 *
 * It includes
 * - low-level \link sd_raw MMC read/write routines \endlink
 * - \link partition partition table support \endlink
 * - a simple \link fat16 FAT16 read/write implementation \endlink
 *
 * \section circuit The circuit
 * The curcuit board is a self-made and self-soldered board consisting of a single
 * copper layer and standard DIL components, except of the MMC/SD card connector.
 *
 * The connector is soldered to the bottom side of the board. It has a simple
 * eject button which, when a card is inserted, needs some space beyond the connector
 * itself. As an additional feature the connector has two electrical switches
 * to detect wether a card is inserted and wether this card is write-protected.
 * 
 * I used two microcontrollers during development, the Atmel ATmega8 with 8kBytes
 * of flash, and its pin-compatible alternative, the ATmega168 with 16kBytes flash.
 * The first one is the one I started with, but when I implemented FAT16 write
 * support, I ran out of flash space and switched to the ATmega168.
 * 
 * \section pictures Pictures
 * \image html pic01.jpg "The circuit board used to implement and test this application."
 * \image html pic02.jpg "The MMC/SD card connector on the soldering side of the circuit board."
 *
 * \section software The software
 * The software is written in pure standard ANSI-C. Sure, it might not be the
 * smallest or the fastest one, but I think it is quite flexible.
 *
 * I implemented a simple command prompt which is accessible via the UART at 9600 Baud. With
 * commands similiar to the Unix shell you can browse different directories, read and write
 * files, create new ones and delete them again. Not all commands are available in all
 * software configurations.
 * - <tt>cat \<file\></tt>\n
 *   Writes a hexdump of \<file\> to the terminal.
 * - <tt>cd \<directory\></tt>\n
 *   Changes current working directory to \<directory\>.
 * - <tt>disk</tt>\n
 *   Shows card manufacturer, status, filesystem capacity and free storage space.
 * - <tt>ls</tt>\n
 *   Shows the content of the current directory.
 * - <tt>mkdir \<directory\></tt>\n
 *   Creates a directory called \<directory\>.
 * - <tt>rm \<file\></tt>\n
 *   Deletes \<file\>.
 * - <tt>sync</tt>\n
 *   Ensures all buffered data is written to the card.
 * - <tt>touch \<file\></tt>\n
 *   Creates \<file\>.
 * - <tt>write \<file\> \<offset\></tt>\n
 *   Writes text to \<file\>, starting from \<offset\>. The text is read
 *   from the UART, line by line. Finish with an empty line.
 *
 * \htmlonly
 * <p>
 * The following table shows some typical code sizes in bytes, using the 20061101 release with malloc()/free():
 * </p>
 *
 * <table border="1" cellpadding="2">
 *     <tr>
 *         <th>layer</th>
 *         <th>code size</th>
 *         <th>static RAM usage</th>
 *     </tr>
 *     <tr>
 *         <td>MMC/SD (read-only)</td>
 *         <td align="right">1576</td>
 *         <td align="right">0</td>
 *     </tr>
 *     <tr>
 *         <td>MMC/SD (read-write)</td>
 *         <td align="right">2202</td>
 *         <td align="right">517</td>
 *     </tr>
 *     <tr>
 *         <td>Partition</td>
 *         <td align="right">418</td>
 *         <td align="right">0</td>
 *     </tr>
 *     <tr>
 *         <td>FAT16 (read-only)</td>
 *         <td align="right">3834</td>
 *         <td align="right">0</td>
 *     </tr>
 *     <tr>
 *         <td>FAT16 (read-write)</td>
 *         <td align="right">7932</td>
 *         <td align="right">0</td>
 *     </tr>
 * </table>
 *
 * <p>
 * The static RAM in the read-write case is used for buffering memory card
 * access. Without this buffer, implementation would have been much more complicated.
 * </p>
 * 
 * <p>
 * Please note that the numbers above do not include the C library functions
 * used, e.g. malloc()/free() and some string functions. These will raise the
 * numbers somewhat if they are not already used in other program parts.
 * </p>
 * 
 * <p>
 * When opening a partition, filesystem, file or directory, a little amount
 * of dynamic RAM is used, as listed in the following table. Alternatively,
 * the same amount of static RAM can be used.
 * </p>
 *
 * <table border="1" cellpadding="2">
 *     <tr>
 *         <th>descriptor</th>
 *         <th>dynamic/static RAM</th>
 *     </tr>
 *     <tr>
 *         <td>partition</td>
 *         <td align="right">17</td>
 *     </tr>
 *     <tr>
 *         <td>filesystem</td>
 *         <td align="right">26</td>
 *     </tr>
 *     <tr>
 *         <td>file</td>
 *         <td align="right">51</td>
 *     </tr>
 *     <tr>
 *         <td>directory</td>
 *         <td align="right">47</td>
 *     </tr>
 * </table>
 * 
 * \endhtmlonly
 *
 * \section adaptation Adapting the software to your needs
 * The only hardware dependent part is the communication
 * layer talking to the memory card. The other parts like partition table and FAT16
 * support are completely independent, you could use them even for managing
 * Compact Flash cards or standard ATAPI hard disks.
 *
 * By changing the MCU* variables in the Makefile, you can use other Atmel
 * microcontrollers or different clock speeds. You might also want to change
 * the configuration defines in the files fat16_config.h, partition_config.h,
 * sd_raw_config.h and sd-reader_config.h. For example, you could disable
 * write support completely if you only need read support.
 * 
 * \section bugs Bugs or comments?
 * If you have comments or found a bug in the software - there might be some
 * of them - you may contact me per mail at [e-mail].
 *
 * \section acknowledgements Acknowledgements
 * Thanks go to Ulrich Radig, who explained on his homepage how to interface
 * MMC cards to the Atmel microcontroller (http://www.ulrichradig.de/).
 * I adapted his work for my circuit. Although this is a very simple
 * solution, I had no problems using it.
 * 
 * \section copyright Copyright 2006-2007 by Roland Riegel
 * This program is free software; you can redistribute it and/or modify it under
 * the terms of the GNU General Public License version 2 as published by
 * the Free Software Foundation (http://www.gnu.org/copyleft/gpl.html).
 */

static uint8_t read_line(char* buffer, uint8_t buffer_length);
static uint32_t strtolong(const char* str);
static uint8_t find_file_in_dir(struct fat16_fs_struct* fs, struct fat16_dir_struct* dd, const char* name, struct fat16_dir_entry_struct* dir_entry);
static struct fat16_file_struct* open_file_in_dir(struct fat16_fs_struct* fs, struct fat16_dir_struct* dd, const char* name); 
static uint8_t print_disk_info(const struct fat16_fs_struct* fs);

UINT  TftGetColor16Bit(UINT R,UINT G,UINT B)
{
   return (  ((R<<8)& 0xf800)|((G<<3)& 0x07e0)|((B>>3) & 0x001f)  );
}

uchar fileNamebuf[9];

int main()
{
    uint  i;
	uchar j,k;
	UINT TempColor;
	DWORD count=0; 
	/* we will just use ordinary idle mode */
   //// set_sleep_mode(SLEEP_MODE_IDLE);

    /* setup uart */
  //  uart_init();
    init_lcd_T176();

    /* setup sd card slot */
    if(!sd_raw_init())
    {
        return 1;
    }

    /* open first partition */
    struct partition_struct* partition = partition_open(sd_raw_read,
                                                        sd_raw_read_interval,
                                                        sd_raw_write,
                                                        sd_raw_write_interval,
                                                        0
                                                       );

    if(!partition)
    {
        /* If the partition did not open, assume the storage device
         * is a "superfloppy", i.e. has no MBR.
         */
        partition = partition_open(sd_raw_read,
                                   sd_raw_read_interval,
                                   sd_raw_write,
                                   sd_raw_write_interval,
                                   -1
                                  );
        if(!partition)
        {
            return 1;
        }
    }

    /* open file system */
    struct fat16_fs_struct* fs = fat16_open(partition);
    if(!fs)
    {
        return 1;
    }

    /* open root directory */
    struct fat16_dir_entry_struct directory;
    fat16_get_dir_entry_of_path(fs, "/", &directory);

    struct fat16_dir_struct* dd = fat16_open_dir(fs, &directory);
    if(!dd)
    {
        return 1;
    }

	init_lcd_T176();
    
    tft_ram_fill(0xf8,0x00);
	Delay_Nms(2000);
	
    
    
  //  while(1)
   // {
	initShowChar();
     RS_(H);   
	  
	              fileNamebuf[0]='2';
	 			  fileNamebuf[4]='.';
				  fileNamebuf[5]='B';
				  fileNamebuf[6]='I';
				  fileNamebuf[7]='N';
				  fileNamebuf[8]='\0';
	            for(i = 0; i < 152; i++)
                {

				  fileNamebuf[1]='0'+i/100%10;
				  fileNamebuf[2]='0'+i/10%10;
				  fileNamebuf[3]='0'+i%10;

                  struct fat16_file_struct* fd = open_file_in_dir(fs, dd, fileNamebuf);
			      
				  for(k=0;k<4;k++)
				  {
                      if(fat16_read_file(fd, tftBuffer, 128)>0) 
					  {
						  for(j=0;j<128;j++,j++)
						  {
							    DATAPORTL=tftBuffer[j+1];
	                             WR_(L);
	                             WR_(H);

								 DATAPORTL=tftBuffer[j];
	                              WR_(L);
	                              WR_(H);
						  }
					  }
					  else 
					  {
					  break;
					  }
				  }  
				  fat16_close_file(fd);
                }


    while(1);   
    /* close file system */
    fat16_close(fs);

    /* close partition */
    partition_close(partition);
    
    return 0;
}

uint8_t read_line(char* buffer, uint8_t buffer_length)
{
    memset(buffer, 0, buffer_length);

    uint8_t read_length = 0;
    while(read_length < buffer_length - 1)
    {
        uint8_t c = uart_getc();

        if(c == 0x08 || c == 0x7f)
        {
            if(read_length < 1)
                continue;

            --read_length;
            buffer[read_length] = '\0';

            uart_putc(0x08);
            uart_putc(' ');
            uart_putc(0x08);

            continue;
        }

        uart_putc(c);

        if(c == '\n')
        {
            buffer[read_length] = '\0';
            break;
        }
        else
        {
            buffer[read_length] = c;
            ++read_length;
        }
    }

    return read_length;
}

uint32_t strtolong(const char* str)
{
    uint32_t l = 0;
    while(*str >= '0' && *str <= '9')
        l = l * 10 + (*str++ - '0');

    return l;
}

uint8_t find_file_in_dir(struct fat16_fs_struct* fs, struct fat16_dir_struct* dd, const char* name, struct fat16_dir_entry_struct* dir_entry)
{
    while(fat16_read_dir(dd, dir_entry))
    {
        if(strcmp(dir_entry->long_name, name) == 0)
        {
            fat16_reset_dir(dd);
            return 1;
        }
    }

    return 0;
}

struct fat16_file_struct* open_file_in_dir(struct fat16_fs_struct* fs, struct fat16_dir_struct* dd, const char* name)
{
    struct fat16_dir_entry_struct file_entry;
    if(!find_file_in_dir(fs, dd, name, &file_entry))
        return 0;

    return fat16_open_file(fs, &file_entry);
}

uint8_t print_disk_info(const struct fat16_fs_struct* fs)
{
    if(!fs)
        return 0;

    struct sd_raw_info disk_info;
    if(!sd_raw_get_info(&disk_info))
        return 0;

    uart_puts_p(PSTR("manuf:  0x")); uart_putc_hex(disk_info.manufacturer); uart_putc('\n');
    uart_puts_p(PSTR("oem:    ")); uart_puts((char*) disk_info.oem); uart_putc('\n');
    uart_puts_p(PSTR("prod:   ")); uart_puts((char*) disk_info.product); uart_putc('\n');
    uart_puts_p(PSTR("rev:    ")); uart_putc_hex(disk_info.revision); uart_putc('\n');
    uart_puts_p(PSTR("serial: 0x")); uart_putdw_hex(disk_info.serial); uart_putc('\n');
    uart_puts_p(PSTR("date:   ")); uart_putw_dec(disk_info.manufacturing_month); uart_putc('/');
                                   uart_putw_dec(disk_info.manufacturing_year); uart_putc('\n');
    uart_puts_p(PSTR("size:   ")); uart_putdw_dec(disk_info.capacity); uart_putc('\n');
    uart_puts_p(PSTR("copy:   ")); uart_putw_dec(disk_info.flag_copy); uart_putc('\n');
    uart_puts_p(PSTR("wr.pr.: ")); uart_putw_dec(disk_info.flag_write_protect_temp); uart_putc('/');
                                   uart_putw_dec(disk_info.flag_write_protect); uart_putc('\n');
    uart_puts_p(PSTR("format: ")); uart_putw_dec(disk_info.format); uart_putc('\n');
    uart_puts_p(PSTR("free:   ")); uart_putdw_dec(fat16_get_fs_free(fs)); uart_putc('/');
                                   uart_putdw_dec(fat16_get_fs_size(fs)); uart_putc('\n');

    return 1;
}

void get_datetime(uint16_t* year, uint8_t* month, uint8_t* day, uint8_t* hour, uint8_t* min, uint8_t* sec)
{
    *year = 2007;
    *month = 1;
    *day = 1;
    *hour = 0;
    *min = 0;
    *sec = 0;
}