macrodriver.h

基于NEC单片的机的程序源码,关于PWM输出的程序.

/*
*******************************************************************************
**
**  This device driver was created by Applilet for the 78K0S/KB1+, 78K0S/KA1+,
**  78K0S/KY1+,78K0S/KU1+ 8-Bit Single-Chip Microcontrollers.
**
**  Copyright(C) NEC Electronics Corporation 2002-2006
**  All rights reserved by NEC Electronics Corporation.
**
**  This program should be used on your own responsibility.
**  NEC Electronics Corporation assumes no responsibility for any losses
**  incurred by customers or third parties arising from the use of this file.
**
**  Filename :	macrodriver.h
**  Abstract :	This file is general header file.
**  APIlib :	NEC78K0SKX1+.lib V1.70 [7 Dec. 2006]
**
**  Device :	uPD78F9234
**
**  Compiler :	NEC/CC78K0
**
*******************************************************************************
*/
#ifndef	_MDSTATUS_
#define _MDSTATUS_
#pragma sfr
#pragma di
#pragma ei
#pragma NOP
#pragma HALT
#pragma STOP

/* data type defintion */
typedef	unsigned long	ULONG;
typedef	unsigned int	UINT;
typedef	unsigned short	USHORT;
typedef	unsigned char	UCHAR;
typedef	unsigned char	BOOL;

#define	ON	1
#define	OFF	0

#define	MD_TRUE		1
#define	MD_FALSE	0

#define	IDLE	0			/* idle status */
#define	READ	1			/* read mode */
#define	WRITE	2			/* write mode */

#define	SET	1
#define	CLEAR	0

#define MD_STATUS	unsigned short
#define MD_STATUSBASE	0x0

/* status list definition */
#define	MD_OK		MD_STATUSBASE+0x0	/* register setting OK */
#define	MD_RESET	MD_STATUSBASE+0x1	/* reset input */
#define	MD_SENDCOMPLETE	MD_STATUSBASE+0x2	/* send data complete */
#define	MD_OVF		MD_STATUSBASE+0x3	/* timer count overflow */

/* error list definition */
#define	MD_ERRORBASE	0x80
#define	MD_ERROR		MD_ERRORBASE+0x0	/* error */
#define	MD_RESOURCEERROR	MD_ERRORBASE+0x1	/* no resource available */
#define	MD_PARITYERROR		MD_ERRORBASE+0x2	/* UARTn parity error */
#define	MD_OVERRUNERROR		MD_ERRORBASE+0x3	/* UARTn overrun error */
#define	MD_FRAMEERROR		MD_ERRORBASE+0x4	/* UARTn frame error */
#define	MD_ARGERROR		MD_ERRORBASE+0x5	/* Error agrument input error */
#define	MD_TIMINGERROR		MD_ERRORBASE+0x6	/* Error timing operation error */
#define	MD_SETPROHIBITED	MD_ERRORBASE+0x7	/* setting prohibited */
#define	MD_DATAEXISTS		MD_ERRORBASE+0x8	/* Data to be transferred next exists in TXBn register */

/* main clock and subclock as clock source */
enum ClockMode { MainClock, RingClock };

/* clear IO register bit and set IO register bit */
#define	ClrIORBit(Reg, ClrBitMap)	Reg &= ~ClrBitMap
#define	SetIORBit(Reg, SetBitMap)	Reg |= SetBitMap

#define	SYSTEMCLOCK	8000000
#define	SUBCLOCK	0
#define	MAINCLOCK	8000000
#define	FXPCLOCK	8000000
#define	FRCLOCK	240000


#endif