ne2000.h

一种操作系统源码核

// The header for an Novell 2000 driver.

#ifndef __NE2000_H
#define __NE2000_H
#define _RTL8019_ISA
#ifdef _RTL8019_ISA
// Rtl8019 isa card
#define NE2000_BASE     0x8300
#define NE2000_RAM_BASE 0x4000
#define NE2000_RAM_SIZE 0x4000


#endif


//    Ne2000 Hardware definitions.

// Offsets from Adapter->IoPAddr of the ports used to access
// the 8390 NIC registers.
//
// The names in parenthesis are the abbreviations by which
// the registers are referred to in the 8390 data sheet.
//
// Some of the offsets appear more than once
// because they have have relevant page 0 and page 1 values,
// or they are different registers when read than they are
// when written. The notation MSB indicates that only the
// MSB can be set for this register, the LSB is assumed 0.

#define NIC_COMMAND         0x0     // (CR)
#define NIC_PAGE_START      0x1     // (PSTART)   MSB, write-only
#define NIC_PHYS_ADDR       0x1     // (PAR0)     page 1
#define NIC_PAGE_STOP       0x2     // (PSTOP)    MSB, write-only
#define NIC_BOUNDARY        0x3     // (BNRY)     MSB
#define NIC_XMIT_START      0x4     // (TPSR)     MSB, write-only
#define NIC_XMIT_STATUS     0x4     // (TSR)      read-only
#define NIC_XMIT_COUNT_LSB  0x5     // (TBCR0)    write-only
#define NIC_XMIT_COUNT_MSB  0x6     // (TBCR1)    write-only
#define NIC_FIFO            0x6     // (FIFO)     read-only
#define NIC_INTR_STATUS     0x7     // (ISR)
#define NIC_CURRENT         0x7     // (CURR)     page 1
#define NIC_MC_ADDR         0x8     // (MAR0)     page 1
#define NIC_CRDA_LSB        0x8     // (CRDA0)
#define NIC_RMT_ADDR_LSB    0x8     // (RSAR0)
#define NIC_CRDA_MSB        0x9     // (CRDA1)
#define NIC_RMT_ADDR_MSB    0x9     // (RSAR1)
#define NIC_RMT_COUNT_LSB   0xa     // (RBCR0)    write-only
#define NIC_RMT_COUNT_MSB   0xb     // (RBCR1)    write-only
#define NIC_RCV_CONFIG      0xc     // (RCR)      write-only
#define NIC_RCV_STATUS      0xc     // (RSR)      read-only
#define NIC_XMIT_CONFIG     0xd     // (TCR)      write-only
#define NIC_FAE_ERR_CNTR    0xd     // (CNTR0)    read-only
#define NIC_DATA_CONFIG     0xe     // (DCR)      write-only
#define NIC_CRC_ERR_CNTR    0xe     // (CNTR1)    read-only
#define NIC_INTR_MASK       0xf     // (IMR)      write-only
#define NIC_MISSED_CNTR     0xf     // (CNTR2)    read-only
#define NIC_RACK_NIC        0x10    // Byte to read or write
#define NIC_RESET           0x1f    // (RESET)

#ifdef _DM9008
#define NIC_DM9008_CONFIGA	0x0a	// read, or read after write
#define NIC_DM9008_CONFIGB	0x0b	// read, or read after write
#define NIC_DM9008_CONFIGC	0x0b	// read or write, page2
#define NIC_DM9008_CONFIGD	0x07	// read or write, page3
#endif

// Constants for the NIC_COMMAND register.
//
// Start/stop the card, start transmissions, and select
// which page of registers was seen through the ports.

#define CR_STOP         (UCHAR)0x01        // reset the card
#define NIC_9346CR          0x01   
#define CR_START        (UCHAR)0x02        // start the card
#define CR_XMIT         (UCHAR)0x04        // begin transmission
#define CR_NO_DMA       (UCHAR)0x20        // stop remote DMA

#define CR_PS0          (UCHAR)0x40        // low bit of page number
#define CR_PS1          (UCHAR)0x80        // high bit of page number
#define CR_PAGE0        (UCHAR)0x00        // select page 0
#define CR_PAGE1        CR_PS0             // select page 1
#define CR_PAGE2        CR_PS1             // select page 2
#define CR_PAGE3        (CR_PS1+CR_PS0)    // select page 3

#define CR_DMA_WRITE    (UCHAR)0x10        // Write
#define CR_DMA_READ     (UCHAR)0x08        // Read
#define CR_SEND         (UCHAR)0x18        // send


// Constants for the NIC_XMIT_STATUS register.
//
// Indicate the result of a packet transmission.

#define TSR_XMIT_OK     (UCHAR)0x01        // transmit with no errors
#define TSR_COLLISION   (UCHAR)0x04        // collided at least once
#define TSR_ABORTED     (UCHAR)0x08        // too many collisions
#define TSR_NO_CARRIER  (UCHAR)0x10        // carrier lost
#define TSR_NO_CDH      (UCHAR)0x40        // no collision detect heartbeat


// Constants for the NIC_INTR_STATUS register.
//
// Indicate the cause of an interrupt.

#define ISR_EMPTY       (UCHAR)0x00        // no bits set in ISR
#define ISR_RCV         (UCHAR)0x01        // packet received with no errors
#define ISR_XMIT        (UCHAR)0x02        // packet transmitted with no errors
#define ISR_RCV_ERR     (UCHAR)0x04        // error on packet reception
#define ISR_XMIT_ERR    (UCHAR)0x08        // error on packet transmission
#define ISR_OVERFLOW    (UCHAR)0x10        // receive buffer overflow
#define ISR_COUNTER     (UCHAR)0x20        // MSB set on tally counter
#define ISR_DMA_DONE    (UCHAR)0x40        // RDC
#define ISR_RESET       (UCHAR)0x80        // (not an interrupt) card is reset


// Constants for the NIC_RCV_CONFIG register.
//
// Configure what type of packets are received.

#define RCR_REJECT_ERR  (UCHAR)0x00        // reject error packets
#define RCR_BROADCAST   (UCHAR)0x04        // receive broadcast packets
#define RCR_MULTICAST   (UCHAR)0x08        // receive multicast packets
#define RCR_ALL_PHYS    (UCHAR)0x10        // receive ALL directed packets
#define RCR_MONITOR     (UCHAR)0x20        // don't collect packets


// Constants for the NIC_RCV_STATUS register.
//
// Indicate the status of a received packet.
//
// These are also used to interpret the status byte in the
// packet header of a received packet.

#define RSR_PACKET_OK   (UCHAR)0x01        // packet received with no errors
#define RSR_CRC_ERROR   (UCHAR)0x02        // packet received with CRC error
#define RSR_MULTICAST   (UCHAR)0x20        // packet received was multicast
#define RSR_DISABLED    (UCHAR)0x40        // received is disabled
#define RSR_DEFERRING   (UCHAR)0x80        // receiver is deferring


// Constants for the NIC_XMIT_CONFIG register.
//
// Configures how packets are transmitted.

#define TCR_NO_LOOPBACK (UCHAR)0x00        // normal operation
#define TCR_LOOPBACK    (UCHAR)0x02        // loopback (set when NIC is stopped)

#define TCR_INHIBIT_CRC (UCHAR)0x01        // inhibit appending of CRC

#define TCR_NIC_LBK     (UCHAR)0x02        // loopback through the NIC
#define TCR_SNI_LBK     (UCHAR)0x04        // loopback through the SNI
#define TCR_COAX_LBK    (UCHAR)0x06        // loopback to the coax


// Constants for the NIC_DATA_CONFIG register.
//
// Set data transfer sizes.

#define DCR_BYTE_WIDE   (UCHAR)0x00        // byte-wide DMA transfers
#define DCR_WORD_WIDE   (UCHAR)0x01        // word-wide DMA transfers

#define DCR_LOOPBACK    (UCHAR)0x00        // loopback mode (TCR must be set)
#define DCR_NORMAL      (UCHAR)0x08        // normal operation

#define DCR_FIFO_2_BYTE (UCHAR)0x00        // 2-byte FIFO threshhold
#define DCR_FIFO_4_BYTE (UCHAR)0x20        // 4-byte FIFO threshhold
#define DCR_FIFO_8_BYTE (UCHAR)0x40        // 8-byte FIFO threshhold
#define DCR_FIFO_12_BYTE (UCHAR)0x60       // 12-byte FIFO threshhold
#define DCR_AUTO_INIT   (UCHAR)0x10        // Auto-init to remove packets from ring


// Constants for the NIC_INTR_MASK register.
//
// Configure which ISR settings actually cause interrupts.

#define IMR_RCV         (UCHAR)0x01        // packet received with no errors
#define IMR_XMIT        (UCHAR)0x02        // packet transmitted with no errors
#define IMR_RCV_ERR     (UCHAR)0x04        // error on packet reception
#define IMR_XMIT_ERR    (UCHAR)0x08        // error on packet transmission
#define IMR_OVERFLOW    (UCHAR)0x10        // receive buffer overflow
#define IMR_COUNTER     (UCHAR)0x20        // MSB set on tally counter
//9346 Command
//#define  EEROM_Normal        (UCHAR)0x0
//#define  EEROM_Auto_Load     (UCHAR)0x40
//#define  EEROM_Program       (UCHAR)0x80
//#define  EECS          (BOOLEAN)(XCHAR[NE2000_BASE+NIC_9346CR]&0x04)
//#define  EESK          (BOOLEAN)(XCHAR[NE2000_BASE+NIC_9346CR]&0x02)
//#define  EEDI          (BOOLEAN)(XCHAR[NE2000_BASE+NIC_9346CR]&0x01)


// Size of the ethernet header, usually 4 bytes, but bug times will be max 6
#define NE2000_HEADER_SIZE          4
#define NE2000_HEADER_MAX_SIZE      6

// Field offset in the ethernet header
#define HEADER_STATUS               0
#define HEADER_NEXT_PACKET          1
#define HEADER_PACKET_LENGTH_LOW    2
#define HEADER_PACKET_LENGTH_HIGH   3

// Number of bytes allowed in a send (min)
#define NE2000_MIN_SEND             60

// Number of bytes allowed in a receive (min)
#define NE2000_MIN_RECEIVE          64

// Number of 256-byte buffers in a transmit buffer.
#define BUFS_PER_TX 6

// For the NicXXX fields, always use the addressing system containing the MSB only.
#define NE2000_NIC_XMIT_START  ((UCHAR)(NE2000_RAM_BASE >> 8))

// The start of the receive space.
#define NE2000_NIC_PAGE_START  (NE2000_NIC_XMIT_START + BUFS_PER_TX)

// The end of the receive space.
#define NE2000_NIC_PAGE_STOP   ((UCHAR)((NE2000_RAM_BASE + NE2000_RAM_SIZE) >> 8))

#endif // __NE2000_H