korat.c

最新版的u-boot,2008-10-18发布

#else
	(void)flash_protect(FLAG_PROTECT_SET, CFG_MONITOR_BASE,
			    CFG_MONITOR_BASE + CFG_MONITOR_LEN - 1,
			    flash_info);
#endif
	/* Env protection ON by default */
	(void)flash_protect(FLAG_PROTECT_SET, CONFIG_ENV_ADDR,
			    CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1,
			    flash_info);
	(void)flash_protect(FLAG_PROTECT_SET, CONFIG_ENV_ADDR_REDUND,
			    CONFIG_ENV_ADDR_REDUND + CONFIG_ENV_SECT_SIZE - 1,
			    flash_info);

	/*
	 * USB suff...
	 */
	if (act == NULL || strcmp(act, "hostdev") == 0) {
		/* SDR Setting */
		mfsdr(SDR0_PFC1, sdr0_pfc1);
		mfsdr(SDR0_USB2D0CR, usb2d0cr);
		mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
		mfsdr(SDR0_USB2H0CR, usb2h0cr);

		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL;
		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ;
		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS;
		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST;
		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST;

		/*
		 * An 8-bit/60MHz interface is the only possible alternative
		 * when connecting the Device to the PHY
		 */
		usb2h0cr = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK;
		usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ;

		/*
		 * To enable the USB 2.0 Device function
		 * through the UTMI interface
		 */
		usb2d0cr = usb2d0cr &~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK;
		usb2d0cr = usb2d0cr | SDR0_USB2D0CR_USB2DEV_SELECTION;

		sdr0_pfc1 = sdr0_pfc1 &~SDR0_PFC1_UES_MASK;
		sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_USB2D_SEL;

		mtsdr(SDR0_PFC1, sdr0_pfc1);
		mtsdr(SDR0_USB2D0CR, usb2d0cr);
		mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
		mtsdr(SDR0_USB2H0CR, usb2h0cr);

		/* clear resets */
		udelay(1000);
		mtsdr(SDR0_SRST1, 0x00000000);
		udelay(1000);
		mtsdr(SDR0_SRST0, 0x00000000);

		printf("USB:   Host(int phy) Device(ext phy)\n");

	} else if (strcmp(act, "dev") == 0) {
		/*-------------------PATCH-------------------------------*/
		mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);

		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL;
		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS;
		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST;
		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST;
		mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);

		udelay(1000);
		mtsdr(SDR0_SRST1, 0x672c6000);

		udelay(1000);
		mtsdr(SDR0_SRST0, 0x00000080);

		udelay(1000);
		mtsdr(SDR0_SRST1, 0x60206000);

		*(unsigned int *)(0xe0000350) = 0x00000001;

		udelay(1000);
		mtsdr(SDR0_SRST1, 0x60306000);
		/*-------------------PATCH-------------------------------*/

		/* SDR Setting */
		mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
		mfsdr(SDR0_USB2H0CR, usb2h0cr);
		mfsdr(SDR0_USB2D0CR, usb2d0cr);
		mfsdr(SDR0_PFC1, sdr0_pfc1);

		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL;
		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_8BIT_60MHZ;
		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PUREN;
		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_DEV;
		usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_DEV;

		usb2h0cr   = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK;
		usb2h0cr   = usb2h0cr | SDR0_USB2H0CR_WDINT_8BIT_60MHZ;

		usb2d0cr = usb2d0cr &~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK;
		usb2d0cr = usb2d0cr | SDR0_USB2D0CR_EBC_SELECTION;

		sdr0_pfc1 = sdr0_pfc1 &~SDR0_PFC1_UES_MASK;
		sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_EBCHR_SEL;

		mtsdr(SDR0_USB2H0CR, usb2h0cr);
		mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
		mtsdr(SDR0_USB2D0CR, usb2d0cr);
		mtsdr(SDR0_PFC1, sdr0_pfc1);

		/* clear resets */
		udelay(1000);
		mtsdr(SDR0_SRST1, 0x00000000);
		udelay(1000);
		mtsdr(SDR0_SRST0, 0x00000000);

		printf("USB:   Device(int phy)\n");
	}

	mfsdr(SDR0_SRST1, reg);		/* enable security/kasumi engines */
	reg &= ~(SDR0_SRST1_CRYP0 | SDR0_SRST1_KASU0);
	mtsdr(SDR0_SRST1, reg);

	/*
	 * Clear PLB4A0_ACR[WRP]
	 * This fix will make the MAL burst disabling patch for the Linux
	 * EMAC driver obsolete.
	 */
	reg = mfdcr(plb4_acr) & ~PLB4_ACR_WRP;
	mtdcr(plb4_acr, reg);

	set_serial_number();
	set_mac_addresses();
	gpio_write_bit(CFG_GPIO_ATMEGA_RESET_, 1);

	return 0;
}

int checkboard(void)
{
	char const *const s = getenv("serial#");
	u8 const rev = in_8((u8 *) CFG_CPLD_BASE + 0);

	printf("Board: Korat, Rev. %X", rev);
	if (s)
		printf(", serial# %s", s);

	printf(".\n       Ethernet PHY 0: ");
	if (gpio_read_out_bit(CFG_GPIO_PHY0_FIBER_SEL))
		printf("fiber");
	else
		printf("copper");

	printf(", PHY 1: ");
	if (gpio_read_out_bit(CFG_GPIO_PHY1_FIBER_SEL))
		printf("fiber");
	else
		printf("copper");

	printf(".\n");
#if defined(CONFIG_KORAT_PERMANENT)
	printf("       Executing permanent copy of U-Boot.\n");
#endif
	return 0;
}

#if defined(CONFIG_PCI) && defined(CONFIG_PCI_PNP)
/*
 * Assign interrupts to PCI devices.
 */
void korat_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
{
	pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, VECNUM_EIRQ2);
}
#endif

/*
 * pci_pre_init
 *
 * This routine is called just prior to registering the hose and gives
 * the board the opportunity to check things. Returning a value of zero
 * indicates that things are bad & PCI initialization should be aborted.
 *
 * Different boards may wish to customize the pci controller structure
 * (add regions, override default access routines, etc) or perform
 * certain pre-initialization actions.
 */
#if defined(CONFIG_PCI)
int pci_pre_init(struct pci_controller *hose)
{
	unsigned long addr;

	/*
	 * Set priority for all PLB3 devices to 0.
	 * Set PLB3 arbiter to fair mode.
	 */
	mfsdr(sdr_amp1, addr);
	mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
	addr = mfdcr(plb3_acr);
	mtdcr(plb3_acr, addr | 0x80000000);

	/*
	 * Set priority for all PLB4 devices to 0.
	 */
	mfsdr(sdr_amp0, addr);
	mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
	addr = mfdcr(plb4_acr) | 0xa0000000;	/* Was 0x8---- */
	mtdcr(plb4_acr, addr);

	/*
	 * Set Nebula PLB4 arbiter to fair mode.
	 */
	/* Segment0 */
	addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
	addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
	addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
	addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
	mtdcr(plb0_acr, addr);

	/* Segment1 */
	addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
	addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
	addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
	addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
	mtdcr(plb1_acr, addr);

#if defined(CONFIG_PCI_PNP)
	hose->fixup_irq = korat_pci_fixup_irq;
#endif

	return 1;
}
#endif /* defined(CONFIG_PCI) */

/*
 * pci_target_init
 *
 * The bootstrap configuration provides default settings for the pci
 * inbound map (PIM). But the bootstrap config choices are limited and
 * may not be sufficient for a given board.
 */
#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
void pci_target_init(struct pci_controller *hose)
{
	/*
	 * Set up Direct MMIO registers
	 */
	/*
	 * PowerPC440EPX PCI Master configuration.
	 * Map one 1Gig range of PLB/processor addresses to PCI memory space.
	 * PLB address 0x80000000-0xBFFFFFFF
	 *     ==> PCI address 0x80000000-0xBFFFFFFF
	 * Use byte reversed out routines to handle endianess.
	 * Make this region non-prefetchable.
	 */
	out32r(PCIX0_PMM0MA, 0x00000000);	/* PMM0 Mask/Attribute */
						/* - disabled b4 setting */
	out32r(PCIX0_PMM0LA, CFG_PCI_MEMBASE);	/* PMM0 Local Address */
	out32r(PCIX0_PMM0PCILA,
	       CFG_PCI_MEMBASE);		/* PMM0 PCI Low Address */
	out32r(PCIX0_PMM0PCIHA, 0x00000000);	/* PMM0 PCI High Address */
	out32r(PCIX0_PMM0MA, 0xE0000001);	/* 512M + No prefetching, */
						/* and enable region */

	out32r(PCIX0_PMM1MA, 0x00000000);	/* PMM0 Mask/Attribute */
						/* - disabled b4 setting */
	out32r(PCIX0_PMM1LA,
	       CFG_PCI_MEMBASE + 0x20000000);	/* PMM0 Local Address */
	out32r(PCIX0_PMM1PCILA,
	       CFG_PCI_MEMBASE + 0x20000000);	/* PMM0 PCI Low Address */
	out32r(PCIX0_PMM1PCIHA, 0x00000000);	/* PMM0 PCI High Address */
	out32r(PCIX0_PMM1MA, 0xE0000001);	/* 512M + No prefetching, */
						/* and enable region */

	out32r(PCIX0_PTM1MS, 0x00000001);	/* Memory Size/Attribute */
	out32r(PCIX0_PTM1LA, 0);		/* Local Addr. Reg */
	out32r(PCIX0_PTM2MS, 0);		/* Memory Size/Attribute */
	out32r(PCIX0_PTM2LA, 0);		/* Local Addr. Reg */

	/*
	 * Set up Configuration registers
	 */

	/* Program the board's subsystem id/vendor id */
	pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
			      CFG_PCI_SUBSYS_VENDORID);
	pci_write_config_word(0, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_ID);

	/* Configure command register as bus master */
	pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);

	/* 240nS PCI clock */
	pci_write_config_word(0, PCI_LATENCY_TIMER, 1);

	/* No error reporting */
	pci_write_config_word(0, PCI_ERREN, 0);

	pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);

	/*
	 * Set up Configuration registers for on-board NEC uPD720101 USB
	 * controller.
	 */
	pci_write_config_dword(PCI_BDF(0x0, 0xC, 0x0), 0xE4, 0x00000020);
}
#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */

#if defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT)
void pci_master_init(struct pci_controller *hose)
{
	unsigned short temp_short;

	/*
	 * Write the PowerPC440 EP PCI Configuration regs.
	 * Enable PowerPC440 EP to be a master on the PCI bus (PMM).
	 * Enable PowerPC440 EP to act as a PCI memory target (PTM).
	 */
	pci_read_config_word(0, PCI_COMMAND, &temp_short);
	pci_write_config_word(0, PCI_COMMAND,
			      temp_short | PCI_COMMAND_MASTER |
			      PCI_COMMAND_MEMORY);
}
#endif

/*
 * is_pci_host
 *
 * This routine is called to determine if a pci scan should be
 * performed. With various hardware environments (especially cPCI and
 * PPMC) it's insufficient to depend on the state of the arbiter enable
 * bit in the strap register, or generic host/adapter assumptions.
 *
 * Rather than hard-code a bad assumption in the general 440 code, the
 * 440 pci code requires the board to decide at runtime.
 *
 * Return 0 for adapter mode, non-zero for host (monarch) mode.
 */
#if defined(CONFIG_PCI)
int is_pci_host(struct pci_controller *hose)
{
	/* Korat is always configured as host. */
	return (1);
}
#endif /* defined(CONFIG_PCI) */

#if defined(CONFIG_POST)
/*
 * Returns 1 if keys pressed to start the power-on long-running tests
 * Called from board_init_f().
 */
int post_hotkeys_pressed(void)
{
	return 0;	/* No hotkeys supported */
}
#endif /* CONFIG_POST */

#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
void ft_board_setup(void *blob, bd_t *bd)
{
	u32 val[4];
	int rc;

	ft_cpu_setup(blob, bd);

	/* Fixup NOR mapping */
	val[0] = 1;				/* chip select number */
	val[1] = 0;				/* always 0 */
	val[2] = gd->bd->bi_flashstart;
	val[3] = gd->bd->bi_flashsize - CFG_FLASH0_SIZE;
	rc = fdt_find_and_setprop(blob, "/plb/opb/ebc", "ranges",
				  val, sizeof(val), 1);
	if (rc)
		printf("Unable to update property NOR mapping, err=%s\n",
		       fdt_strerror(rc));
}
#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */