cpu_init.c

来自「最新版的u-boot,2008-10-18发布」· C语言 代码 · 共 670 行 · 第 1/2 页

#endif

	/* enable instruction cache now */
	icache_enable();
}

/*
 * initialize higher level parts of CPU like timers
 */
int cpu_init_r(void)
{
	return (0);
}

void uart_port_conf(void)
{
	volatile gpio_t *gpio = (gpio_t *)MMAP_GPIO;

	/* Setup Ports: */
	switch (CFG_UART_PORT) {
	case 0:
		gpio->par_uart |= UART0_ENABLE_MASK;
		break;
	case 1:
		gpio->par_uart |= UART1_ENABLE_MASK;
		break;
	case 2:
		gpio->par_uart |= UART2_ENABLE_MASK;
		break;
	}
}
#endif				/* #if defined(CONFIG_M5275) */

#if defined(CONFIG_M5282)
/*
 * Breath some life into the CPU...
 *
 * Set up the memory map,
 * initialize a bunch of registers,
 * initialize the UPM's
 */
void cpu_init_f(void)
{
#ifndef CONFIG_WATCHDOG
	/* disable watchdog if we aren't using it */
	MCFWTM_WCR = 0;
#endif

#ifndef CONFIG_MONITOR_IS_IN_RAM
	/* Set speed /PLL */
	MCFCLOCK_SYNCR =
	    MCFCLOCK_SYNCR_MFD(CFG_MFD) | MCFCLOCK_SYNCR_RFD(CFG_RFD);
	while (!(MCFCLOCK_SYNSR & MCFCLOCK_SYNSR_LOCK)) ;

	MCFGPIO_PBCDPAR = 0xc0;

	/* Set up the GPIO ports */
#ifdef CFG_PEPAR
	MCFGPIO_PEPAR = CFG_PEPAR;
#endif
#ifdef	CFG_PFPAR
	MCFGPIO_PFPAR = CFG_PFPAR;
#endif
#ifdef CFG_PJPAR
	MCFGPIO_PJPAR = CFG_PJPAR;
#endif
#ifdef CFG_PSDPAR
	MCFGPIO_PSDPAR = CFG_PSDPAR;
#endif
#ifdef CFG_PASPAR
	MCFGPIO_PASPAR = CFG_PASPAR;
#endif
#ifdef CFG_PEHLPAR
	MCFGPIO_PEHLPAR = CFG_PEHLPAR;
#endif
#ifdef CFG_PQSPAR
	MCFGPIO_PQSPAR = CFG_PQSPAR;
#endif
#ifdef CFG_PTCPAR
	MCFGPIO_PTCPAR = CFG_PTCPAR;
#endif
#ifdef CFG_PTDPAR
	MCFGPIO_PTDPAR = CFG_PTDPAR;
#endif
#ifdef CFG_PUAPAR
	MCFGPIO_PUAPAR = CFG_PUAPAR;
#endif

#ifdef CFG_DDRUA
	MCFGPIO_DDRUA = CFG_DDRUA;
#endif

	/* This is probably a bad place to setup chip selects, but everyone
	   else is doing it! */

#if defined(CFG_CS0_BASE) & defined(CFG_CS0_SIZE) & \
    defined(CFG_CS0_WIDTH) & defined(CFG_CS0_WS)

	MCFCSM_CSAR0 = (CFG_CS0_BASE >> 16) & 0xFFFF;

#if (CFG_CS0_WIDTH == 8)
#define	 CFG_CS0_PS  MCFCSM_CSCR_PS_8
#elif (CFG_CS0_WIDTH == 16)
#define	 CFG_CS0_PS  MCFCSM_CSCR_PS_16
#elif (CFG_CS0_WIDTH == 32)
#define	 CFG_CS0_PS  MCFCSM_CSCR_PS_32
#else
#error	"CFG_CS0_WIDTH: Fault - wrong bus with for CS0"
#endif
	MCFCSM_CSCR0 = MCFCSM_CSCR_WS(CFG_CS0_WS)
	    | CFG_CS0_PS | MCFCSM_CSCR_AA;

#if (CFG_CS0_RO != 0)
	MCFCSM_CSMR0 = MCFCSM_CSMR_BAM(CFG_CS0_SIZE - 1)
	    | MCFCSM_CSMR_WP | MCFCSM_CSMR_V;
#else
	MCFCSM_CSMR0 = MCFCSM_CSMR_BAM(CFG_CS0_SIZE - 1) | MCFCSM_CSMR_V;
#endif
#else
#warning "Chip Select 0 are not initialized/used"
#endif

#if defined(CFG_CS1_BASE) & defined(CFG_CS1_SIZE) & \
    defined(CFG_CS1_WIDTH) & defined(CFG_CS1_WS)

	MCFCSM_CSAR1 = (CFG_CS1_BASE >> 16) & 0xFFFF;

#if (CFG_CS1_WIDTH == 8)
#define	 CFG_CS1_PS  MCFCSM_CSCR_PS_8
#elif (CFG_CS1_WIDTH == 16)
#define	 CFG_CS1_PS  MCFCSM_CSCR_PS_16
#elif (CFG_CS1_WIDTH == 32)
#define	 CFG_CS1_PS  MCFCSM_CSCR_PS_32
#else
#error	"CFG_CS1_WIDTH: Fault - wrong bus with for CS1"
#endif
	MCFCSM_CSCR1 = MCFCSM_CSCR_WS(CFG_CS1_WS)
	    | CFG_CS1_PS | MCFCSM_CSCR_AA;

#if (CFG_CS1_RO != 0)
	MCFCSM_CSMR1 = MCFCSM_CSMR_BAM(CFG_CS1_SIZE - 1)
	    | MCFCSM_CSMR_WP | MCFCSM_CSMR_V;
#else
	MCFCSM_CSMR1 = MCFCSM_CSMR_BAM(CFG_CS1_SIZE - 1)
	    | MCFCSM_CSMR_V;
#endif
#else
#warning "Chip Select 1 are not initialized/used"
#endif

#if defined(CFG_CS2_BASE) & defined(CFG_CS2_SIZE) & \
    defined(CFG_CS2_WIDTH) & defined(CFG_CS2_WS)

	MCFCSM_CSAR2 = (CFG_CS2_BASE >> 16) & 0xFFFF;

#if (CFG_CS2_WIDTH == 8)
#define	 CFG_CS2_PS  MCFCSM_CSCR_PS_8
#elif (CFG_CS2_WIDTH == 16)
#define	 CFG_CS2_PS  MCFCSM_CSCR_PS_16
#elif (CFG_CS2_WIDTH == 32)
#define	 CFG_CS2_PS  MCFCSM_CSCR_PS_32
#else
#error	"CFG_CS2_WIDTH: Fault - wrong bus with for CS2"
#endif
	MCFCSM_CSCR2 = MCFCSM_CSCR_WS(CFG_CS2_WS)
	    | CFG_CS2_PS | MCFCSM_CSCR_AA;

#if (CFG_CS2_RO != 0)
	MCFCSM_CSMR2 = MCFCSM_CSMR_BAM(CFG_CS2_SIZE - 1)
	    | MCFCSM_CSMR_WP | MCFCSM_CSMR_V;
#else
	MCFCSM_CSMR2 = MCFCSM_CSMR_BAM(CFG_CS2_SIZE - 1)
	    | MCFCSM_CSMR_V;
#endif
#else
#warning "Chip Select 2 are not initialized/used"
#endif

#if defined(CFG_CS3_BASE) & defined(CFG_CS3_SIZE) & \
    defined(CFG_CS3_WIDTH) & defined(CFG_CS3_WS)

	MCFCSM_CSAR3 = (CFG_CS3_BASE >> 16) & 0xFFFF;

#if (CFG_CS3_WIDTH == 8)
#define	 CFG_CS3_PS  MCFCSM_CSCR_PS_8
#elif (CFG_CS3_WIDTH == 16)
#define	 CFG_CS3_PS  MCFCSM_CSCR_PS_16
#elif (CFG_CS3_WIDTH == 32)
#define	 CFG_CS3_PS  MCFCSM_CSCR_PS_32
#else
#error	"CFG_CS3_WIDTH: Fault - wrong bus with for CS1"
#endif
	MCFCSM_CSCR3 = MCFCSM_CSCR_WS(CFG_CS3_WS)
	    | CFG_CS3_PS | MCFCSM_CSCR_AA;

#if (CFG_CS3_RO != 0)
	MCFCSM_CSMR3 = MCFCSM_CSMR_BAM(CFG_CS3_SIZE - 1)
	    | MCFCSM_CSMR_WP | MCFCSM_CSMR_V;
#else
	MCFCSM_CSMR3 = MCFCSM_CSMR_BAM(CFG_CS3_SIZE - 1)
	    | MCFCSM_CSMR_V;
#endif
#else
#warning "Chip Select 3 are not initialized/used"
#endif

#endif				/* CONFIG_MONITOR_IS_IN_RAM */

	/* defer enabling cache until boot (see do_go) */
	/* icache_enable(); */
}

/*
 * initialize higher level parts of CPU like timers
 */
int cpu_init_r(void)
{
	return (0);
}

void uart_port_conf(void)
{
	/* Setup Ports: */
	switch (CFG_UART_PORT) {
	case 0:
		MCFGPIO_PUAPAR &= 0xFc;
		MCFGPIO_PUAPAR |= 0x03;
		break;
	case 1:
		MCFGPIO_PUAPAR &= 0xF3;
		MCFGPIO_PUAPAR |= 0x0C;
		break;
	case 2:
		MCFGPIO_PASPAR &= 0xFF0F;
		MCFGPIO_PASPAR |= 0x00A0;
		break;
	}
}
#endif

#if defined(CONFIG_M5249)
/*
 * Breath some life into the CPU...
 *
 * Set up the memory map,
 * initialize a bunch of registers,
 * initialize the UPM's
 */
void cpu_init_f(void)
{
	/*
	 *  NOTE: by setting the GPIO_FUNCTION registers, we ensure that the UART pins
	 *        (UART0: gpio 30,27, UART1: gpio 31, 28) will be used as UART pins
	 *        which is their primary function.
	 *        ~Jeremy
	 */
	mbar2_writeLong(MCFSIM_GPIO_FUNC, CFG_GPIO_FUNC);
	mbar2_writeLong(MCFSIM_GPIO1_FUNC, CFG_GPIO1_FUNC);
	mbar2_writeLong(MCFSIM_GPIO_EN, CFG_GPIO_EN);
	mbar2_writeLong(MCFSIM_GPIO1_EN, CFG_GPIO1_EN);
	mbar2_writeLong(MCFSIM_GPIO_OUT, CFG_GPIO_OUT);
	mbar2_writeLong(MCFSIM_GPIO1_OUT, CFG_GPIO1_OUT);

	/*
	 *  dBug Compliance:
	 *    You can verify these values by using dBug's 'ird'
	 *    (Internal Register Display) command
	 *    ~Jeremy
	 *
	 */
	mbar_writeByte(MCFSIM_MPARK, 0x30);	/* 5249 Internal Core takes priority over DMA */
	mbar_writeByte(MCFSIM_SYPCR, 0x00);
	mbar_writeByte(MCFSIM_SWIVR, 0x0f);
	mbar_writeByte(MCFSIM_SWSR, 0x00);
	mbar_writeLong(MCFSIM_IMR, 0xfffffbff);
	mbar_writeByte(MCFSIM_SWDICR, 0x00);
	mbar_writeByte(MCFSIM_TIMER1ICR, 0x00);
	mbar_writeByte(MCFSIM_TIMER2ICR, 0x88);
	mbar_writeByte(MCFSIM_I2CICR, 0x00);
	mbar_writeByte(MCFSIM_UART1ICR, 0x00);
	mbar_writeByte(MCFSIM_UART2ICR, 0x00);
	mbar_writeByte(MCFSIM_ICR6, 0x00);
	mbar_writeByte(MCFSIM_ICR7, 0x00);
	mbar_writeByte(MCFSIM_ICR8, 0x00);
	mbar_writeByte(MCFSIM_ICR9, 0x00);
	mbar_writeByte(MCFSIM_QSPIICR, 0x00);

	mbar2_writeLong(MCFSIM_GPIO_INT_EN, 0x00000080);
	mbar2_writeByte(MCFSIM_INTBASE, 0x40);	/* Base interrupts at 64 */
	mbar2_writeByte(MCFSIM_SPURVEC, 0x00);
	mbar2_writeLong(MCFSIM_IDECONFIG1, 0x00000020);	/* Enable a 1 cycle pre-drive cycle on CS1 */

	/* Setup interrupt priorities for gpio7 */
	/* mbar2_writeLong(MCFSIM_INTLEV5, 0x70000000); */

	/* IDE Config registers */
	mbar2_writeLong(MCFSIM_IDECONFIG1, 0x00000020);
	mbar2_writeLong(MCFSIM_IDECONFIG2, 0x00000000);

	/*
	 *  Setup chip selects...
	 */

	mbar_writeShort(MCFSIM_CSAR1, CFG_CSAR1);
	mbar_writeShort(MCFSIM_CSCR1, CFG_CSCR1);
	mbar_writeLong(MCFSIM_CSMR1, CFG_CSMR1);

	mbar_writeShort(MCFSIM_CSAR0, CFG_CSAR0);
	mbar_writeShort(MCFSIM_CSCR0, CFG_CSCR0);
	mbar_writeLong(MCFSIM_CSMR0, CFG_CSMR0);

	/* enable instruction cache now */
	icache_enable();
}

/*
 * initialize higher level parts of CPU like timers
 */
int cpu_init_r(void)
{
	return (0);
}

void uart_port_conf(void)
{
	/* Setup Ports: */
	switch (CFG_UART_PORT) {
	case 0:
		break;
	case 1:
		break;
	}
}
#endif				/* #if defined(CONFIG_M5249) */