rx433.lst

nrf9e5带超时无线收发：从串口接收数据（靠超时判断而不是字节判断）

C51 COMPILER V7.50   RX433                                                                 10/21/2008 10:38:16 PAGE 1   


C51 COMPILER V7.50, COMPILATION OF MODULE RX433
OBJECT MODULE PLACED IN rx433.OBJ
COMPILER INVOKED BY: C:\Keil\C51\BIN\C51.EXE rx433.c BROWSE DEBUG OBJECTEXTEND

line level    source

   1          /*******************************************
   2          双机无线收发接收端程序：
   3                  将无线接收到的字符显示在PC串口。
   4          
   5          修改：将接收的数据个数由原先的缓冲区大小判断改成由接收到第一个字节判断。
   6          ******************************************/
   7          
   8          #include <Nordic\reg9e5.h>
   9          
  10          #define   HFREQ 0                     // 0=433MHz, 1=868/915MHz     (方便更改）
  11          #define   UART_BUFFER_SIZE    10       //定义串口缓冲区大小 10 bytes
  12          
  13          unsigned char UART_BUFFER[UART_BUFFER_SIZE+1];
  14          
  15          
  16          //串口发送1Byte
  17          void PutChar(char c)
  18          {
  19   1          while(!TI)                              //Wait until finished seri-port transmitting
  20   1              ;
  21   1              TI = 0;                                //Clear interrupt flag
  22   1          SBUF = c;                              //sending a byte
  23   1      }
  24          
  25          //串口发送字符串
  26          void PutString(const char *s,unsigned char strlen)
  27          {
  28   1          unsigned char k;
  29   1              //EIE &= 0xF0;
  30   1          for(k=1;k<=strlen;k++)
  31   1             {
  32   2               PutChar(*(s+k));
  33   2             }
  34   1              //EIE |= 0x0F;
  35   1      }
  36          
  37          
  38          unsigned char SpiReadWrite(unsigned char b)
  39          {
  40   1          EXIF &= ~0x20;                  // Clear SPI interrupt        (EXIP.5=0)
  41   1          SPI_DATA = b;                   // Move byte to send to SPI data register
  42   1          while((EXIF & 0x20) == 0x00)    // Wait until SPI hs finished transmitting   (测试EXIF.5的状态)
  43   1                ;
  44   1          return SPI_DATA;
  45   1      }
  46          
  47          
  48          void Receiver(void)
  49          {
  50   1          unsigned char i=0;
  51   1          TXEN = 0;
  52   1          TRX_CE = 1;                     //进入接收模式
  53   1          while(DR == 0)                  //DR=0表示数据未准备好，等待
  54   1              ;
  55   1      
C51 COMPILER V7.50   RX433                                                                 10/21/2008 10:38:16 PAGE 2   

  56   1          TRX_CE=0;                       //进入待机模式才可读写SPI
  57   1          RACSN = 0;                      //内部SPI开始等待命令（1到0的跳变）
  58   1          SpiReadWrite(RRP);  
  59   1      /*
  60   1      while(DR == 1)
  61   1      {       UART_BUFFER[i] = SpiReadWrite(0); 
  62   1          i++;
  63   1      }
  64   1      */                      
  65   1              UART_BUFFER[0] = SpiReadWrite(0); 
  66   1              for(i=1;i<=UART_BUFFER[0];i++)   //****修改处*****
  67   1              {
  68   2                      UART_BUFFER[i] = SpiReadWrite(0);                
  69   2              }
  70   1              P04 = ~P04;
  71   1          RACSN = 1;
  72   1      //    TRX_CE = 1;                     //这时MCU才从SPI读数据
  73   1      }
  74          
  75          void UART_Init(void)                //nRF9E5串口初始化
  76          {
  77   1          TH1 = 0xE6;                      // 9600@16MHz (when T1M=1 and SMOD=1)
  78   1          CKCON |= 0x30;                  // T1M=1 (/4 timer clock)
  79   1          PCON = 0x80;                    // SMOD=1 (double baud rate)
  80   1          SCON = 0x52;                    // Serial mode1, enable receiver
  81   1          TMOD = 0x20;                    // Timer1 8bit auto reload 
  82   1          TR1 = 1;                        // Start timer1  
  83   1          P0_ALT |= 0x06;
  84   1          P0_DIR  = 0xA2;                 // P0.1 (RxD) is input
  85   1      }
  86          
  87          void Init(void)                     //nRF9E5无线模块初始化
  88          {
  89   1          unsigned char tmp,cklf;
  90   1          SPICLK = 0;                     // Max SPI clock
  91   1          SPI_CTRL = 0x02;                // Connect internal SPI controller to Radio
  92   1      
  93   1          // Configure Radio:
  94   1          RACSN = 0;
  95   1          SpiReadWrite(WRC | 0x03);       // Write to RF config address 3 (RX payload)
  96   1          SpiReadWrite(0x01);             // One byte RX payload
  97   1          SpiReadWrite(0x01);             // One byte TX payload
  98   1          RACSN = 1;
  99   1      
 100   1          RACSN = 0;
 101   1          SpiReadWrite(RRC | 0x01);       // Read RF config address 1
 102   1          tmp = SpiReadWrite(0) & 0xf1;   // Clear the power and frequency setting bits  
 103   1                                          //PA_PWR[1:0]=00(输出电源-10dBm）Bit1：HFREQ_PLL=0（433MHz)
 104   1          RACSN = 1;
 105   1      
 106   1          RACSN = 0;
 107   1          SpiReadWrite(WRC | 0x01);           // Write RF config address 1
 108   1          SpiReadWrite(tmp | (HFREQ << 1));   // Change to 433 or 868/915MHz defined by HFREQ above:
 109   1          RACSN = 1;
 110   1      
 111   1      
 112   1          // 将时钟频率改为16MHz:
 113   1          RACSN = 0;
 114   1          SpiReadWrite(RRC | 0x09);
 115   1          cklf = SpiReadWrite(0) | 0x1c;
 116   1          RACSN = 1;
 117   1          RACSN = 0;
C51 COMPILER V7.50   RX433                                                                 10/21/2008 10:38:16 PAGE 3   

 118   1          SpiReadWrite(WRC | 0x09);
 119   1          SpiReadWrite(cklf);
 120   1          RACSN = 1;
 121   1      
 122   1      
 123   1          RACSN = 0;
 124   1          SpiReadWrite(WRC | 0x05);       //设置本接收器可接受的地址,与tx433里的配置一样才可通信
 125   1          SpiReadWrite(0x18);
 126   1          SpiReadWrite(0x32);
 127   1          SpiReadWrite(0x40);
 128   1          SpiReadWrite(0xAF);
 129   1          RACSN = 1;
 130   1      
 131   1          RACSN = 0;
 132   1          SpiReadWrite(WRC | 0x03);       //设置本接收器可接受的数据宽度,与tx433里的配置一样才可通信
 133   1          SpiReadWrite(0x20);             //接受数据宽度为32个字节
 134   1          RACSN = 1;
 135   1      
 136   1      
 137   1      }
 138          
 139          void main(void)
 140          {
 141   1          Init();
 142   1          UART_Init();
 143   1      //    EA=1;
 144   1      //    ES=1;
 145   1      
 146   1          while(1)
 147   1           { 
 148   2            Receiver();
 149   2            PutString(UART_BUFFER,UART_BUFFER[0]);
 150   2           }
 151   1      }


MODULE INFORMATION:   STATIC OVERLAYABLE
   CODE SIZE        =    277    ----
   CONSTANT SIZE    =   ----    ----
   XDATA SIZE       =   ----    ----
   PDATA SIZE       =   ----    ----
   DATA SIZE        =     11       3
   IDATA SIZE       =   ----    ----
   BIT SIZE         =   ----    ----
END OF MODULE INFORMATION.


C51 COMPILATION COMPLETE.  0 WARNING(S),  0 ERROR(S)