usb.c

iar 安装使用的方法。其中包括一些工程模板

//*****************************************************************************
//
// usb.c - Driver for the USB Interface.
//
// Copyright (c) 2007-2008 Luminary Micro, Inc.  All rights reserved.
// 
// Software License Agreement
// 
// Luminary Micro, Inc. (LMI) is supplying this software for use solely and
// exclusively on LMI's microcontroller products.
// 
// The software is owned by LMI and/or its suppliers, and is protected under
// applicable copyright laws.  All rights are reserved.  You may not combine
// this software with "viral" open-source software in order to form a larger
// program.  Any use in violation of the foregoing restrictions may subject
// the user to criminal sanctions under applicable laws, as well as to civil
// liability for the breach of the terms and conditions of this license.
// 
// THIS SOFTWARE IS PROVIDED "AS IS".  NO WARRANTIES, WHETHER EXPRESS, IMPLIED
// OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF
// MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE.
// LMI SHALL NOT, IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR
// CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER.
// 
// This is part of revision 2752 of the Stellaris Peripheral Driver Library.
//
//*****************************************************************************

#include "../hw_types.h"
#include "../hw_memmap.h"
#include "../hw_ints.h"
#include "../hw_usb.h"
#include "debug.h"
#include "interrupt.h"
#include "usb.h"

//*****************************************************************************
//
// Amount to shift the RX interrupt sources by in the flags used in the
// interrupt calls.
//
//*****************************************************************************
#define USB_INT_RX_SHIFT        8

//*****************************************************************************
//
// Amount to shift the status interrupt sources by in the flags used in the
// interrupt calls.
//
//*****************************************************************************
#define USB_INT_STATUS_SHIFT    24

//*****************************************************************************
//
// Amount to shift the RX endpoint status sources by in the flags used in the
// calls.
//
//*****************************************************************************
#define USB_RX_EPSTATUS_SHIFT   16

//*****************************************************************************
//
// Converts from an endpoint specifier to the offset of the endpoint's
// control/status registers.
//
//*****************************************************************************
#define EP_OFFSET(Endpoint)     (Endpoint - 0x10)

//*****************************************************************************
//
//! \addtogroup usb_api
//! @{
//
//*****************************************************************************

//*****************************************************************************
//
// Sets one of the indexed registers.
//
// \param ulBase specifies the USB module base address.
// \param ulEndpoint is the endpoint index to target for this write.
// \param ulIndexedReg is the indexed register to write to.
// \param ucValue is the value to write to the register.
//
// This function is used to access the indexed registers for each endpoint.
// The only registers that are indexed are the FIFO configuration registers
// which are not used after configuration.
//
// \return None.
//
//*****************************************************************************
static void
USBIndexWrite(unsigned long ulBase, unsigned long ulEndpoint,
              unsigned long ulIndexedReg, unsigned long ulValue,
              unsigned long ulSize)
{
    unsigned long ulIndex;

    //
    // Check the arguments.
    //
    ASSERT(ulBase == USB0_BASE);
    ASSERT((ulEndpoint == 0) || (ulEndpoint == 1) || (ulEndpoint == 2) ||
           (ulEndpoint == 3));
    ASSERT((ulSize == 1) || (ulSize == 2));

    //
    // Save the old index in case it was in use.
    //
    ulIndex = HWREGB(ulBase + USB_O_EPIDX);

    //
    // Set the index.
    //
    HWREGB(ulBase + USB_O_EPIDX) = ulEndpoint;

    //
    // Determine the size of the register value.
    //
    if(ulSize == 1)
    {
        //
        // Set the value.
        //
        HWREGB(ulBase + ulIndexedReg) = ulValue;
    }
    else
    {
        //
        // Set the value.
        //
        HWREGH(ulBase + ulIndexedReg) = ulValue;
    }

    //
    // Restore the old index in case it was in use.
    //
    HWREGB(ulBase + USB_O_EPIDX) = ulIndex;
}

//*****************************************************************************
//
// Reads one of the indexed registers.
//
// \param ulBase specifies the USB module base address.
// \param ulEndpoint is the endpoint index to target for this write.
// \param ulIndexedReg is the indexed register to write to.
//
// This function is used interally to access the indexed registers for each
// endpoint.  The only registers that are indexed are the FIFO configuration
// registers which are not used after configuration.
//
// \return The value in the register requested.
//
//*****************************************************************************
static unsigned long
USBIndexRead(unsigned long ulBase, unsigned long ulEndpoint,
             unsigned long ulIndexedReg, unsigned long ulSize)
{
    unsigned char ulIndex;
    unsigned char ulValue;

    //
    // Check the arguments.
    //
    ASSERT(ulBase == USB0_BASE);
    ASSERT((ulEndpoint == 0) || (ulEndpoint == 1) || (ulEndpoint == 2) ||
           (ulEndpoint == 3));
    ASSERT((ulSize == 1) || (ulSize == 2));

    //
    // Save the old index in case it was in use.
    //
    ulIndex = HWREGB(ulBase + USB_O_EPIDX);

    //
    // Set the index.
    //
    HWREGB(ulBase + USB_O_EPIDX) = ulEndpoint;

    //
    // Determine the size of the register value.
    //
    if(ulSize == 1)
    {
        //
        // Get the value.
        //
        ulValue = HWREGB(ulBase + ulIndexedReg);
    }
    else
    {
        //
        // Get the value.
        //
        ulValue = HWREGH(ulBase + ulIndexedReg);
    }

    //
    // Restore the old index in case it was in use.
    //
    HWREGB(ulBase + USB_O_EPIDX) = ulIndex;

    //
    // Return the register's value.
    //
    return(ulValue);
}

//*****************************************************************************
//
//! Puts the USB bus in a suspended state.
//!
//! \param ulBase specifies the USB module base address.
//!
//! When used in host mode, this function will put the USB bus in the suspended
//! state.
//!
//! \note This function should only be called in host mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostSuspend(unsigned long ulBase)
{
    //
    // Check the arguments.
    //
    ASSERT(ulBase == USB0_BASE);

    //
    // Send the suspend signaling to the USB bus.
    //
    HWREGB(ulBase + USB_O_POWER) |= USB_POWER_SUSPEND;
}

//*****************************************************************************
//
//! Handles the USB bus reset condition.
//!
//! \param ulBase specifies the USB module base address.
//! \param bStart specifies whether to start or stop signaling reset on the USB
//! bus.
//!
//! When this function is called with the \e bStart parameter set to \b true,
//! this function will cause the start of a reset condition on the USB bus.
//! The caller should then delay at least 20ms before calling this function
//! again with the \e bStart parameter set to \b false.
//!
//! \note This function should only be called in host mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostReset(unsigned long ulBase, tBoolean bStart)
{
    //
    // Check the arguments.
    //
    ASSERT(ulBase == USB0_BASE);

    //
    // Send a reset signal to the bus.
    //
    if(bStart)
    {
        HWREGB(ulBase + USB_O_POWER) |= USB_POWER_RESET;
    }
    else
    {
        HWREGB(ulBase + USB_O_POWER) &= ~USB_POWER_RESET;
    }
}

//*****************************************************************************
//
//! Handles the USB bus resume condition.
//!
//! \param ulBase specifies the USB module base address.
//! \param bStart specifies if the USB controller is entering or leaving the
//! resume signaling state.
//!
//! When in device mode this function will bring the USB controller out of the
//! suspend state.  This call should first be made with the \e bStart parameter
//! set to \b true to start resume signaling.  The device application should
//! then delay at least 10ms but not more than 15ms before calling this
//! function with the \e bStart parameter set to \b false.
//!
//! When in host mode this function will signal devices to leave the suspend
//! state.  This call should first be made with the \e bStart parameter set to
//! \b true to start resume signaling.  The host application should then delay
//! at least 20ms before calling this function with the \e bStart parameter set
//! to \b false.  This will cause the controller to complete the resume
//! signaling on the USB bus.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostResume(unsigned long ulBase, tBoolean bStart)
{
    //
    // Check the arguments.
    //
    ASSERT(ulBase == USB0_BASE);

    //
    // Send a resume signal to the bus.
    //
    if(bStart)
    {
        HWREGB(ulBase + USB_O_POWER) |= USB_POWER_RESUME;
    }
    else
    {
        HWREGB(ulBase + USB_O_POWER) &= ~USB_POWER_RESUME;
    }
}

//*****************************************************************************
//
//! Returns the current speed of the USB device connected.
//!
//! \param ulBase specifies the USB module base address.
//!
//! This function will return the current speed of the USB bus.
//!
//! \note This function should only be called in host mode.
//!
//! \return Returns either \b USB_LOW_SPEED, \b USB_FULL_SPEED, or
//! \b USB_UNDEF_SPEED.
//
//*****************************************************************************
unsigned long
USBHostSpeedGet(unsigned long ulBase)
{
    //
    // Check the arguments.
    //
    ASSERT(ulBase == USB0_BASE);

    //
    // If the Full Speed device bit is set, then this is a full speed device.
    //
    if(HWREGB(ulBase + USB_O_DEVCTL) & USB_DEVCTL_FSDEV)
    {
        return(USB_FULL_SPEED);
    }

    //
    // If the Low Speed device bit is set, then this is a low speed device.
    //
    if(HWREGB(ulBase + USB_O_DEVCTL) & USB_DEVCTL_LSDEV)
    {
        return(USB_LOW_SPEED);
    }

    //
    // The device speed is not known.
    //
    return(USB_UNDEF_SPEED);
}

//*****************************************************************************
//
//! Returns the status of the USB interrupts.
//!
//! \param ulBase specifies the USB module base address.
//!
//! This function will read the source of the interrupt for the USB controller.
//! There are three groups of interrupt sources, IN Endpoints, OUT Endpoints,
//! and general status changes.  This call will return the current status for
//! all of these interrupts.  The bit values returned should be compared
//! against the \b USB_HOST_IN, \b USB_HOST_OUT, \b USB_HOST_EP0,
//! \b USB_DEV_IN, \b USB_DEV_OUT, and \b USB_DEV_EP0 values.
//!
//! \note This call will clear the source of all of the general status
//! interrupts.
//!
//! \return Returns the status of the sources for the USB controller's
//! interrupt.
//
//*****************************************************************************
unsigned long
USBIntStatus(unsigned long ulBase)
{
    unsigned long ulStatus;