mpc8555cds.c

U-BOOT,著名的Bootloader程序

	puts("Initializing\n");

#if defined(CONFIG_DDR_DLL)
	{
		/*
		 * Work around to stabilize DDR DLL MSYNC_IN.
		 * Errata DDR9 seems to have been fixed.
		 * This is now the workaround for Errata DDR11:
		 *    Override DLL = 1, Course Adj = 1, Tap Select = 0
		 */

		volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR);

		gur->ddrdllcr = 0x81000000;
		asm("sync;isync;msync");
		udelay(200);
	}
#endif
	dram_size = spd_sdram();

#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
	/*
	 * Initialize and enable DDR ECC.
	 */
	ddr_enable_ecc(dram_size);
#endif
	/*
	 * SDRAM Initialization
	 */
	sdram_init();

	puts("    DDR: ");
	return dram_size;
}

/*
 * Initialize Local Bus
 */
void
local_bus_init(void)
{
	volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR);
	volatile ccsr_lbc_t *lbc = (void *)(CFG_MPC85xx_LBC_ADDR);

	uint clkdiv;
	uint lbc_hz;
	sys_info_t sysinfo;
	uint temp_lbcdll;

	/*
	 * Errata LBC11.
	 * Fix Local Bus clock glitch when DLL is enabled.
	 *
	 * If localbus freq is < 66Mhz, DLL bypass mode must be used.
	 * If localbus freq is > 133Mhz, DLL can be safely enabled.
	 * Between 66 and 133, the DLL is enabled with an override workaround.
	 */

	get_sys_info(&sysinfo);
	clkdiv = lbc->lcrr & 0x0f;
	lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;

	if (lbc_hz < 66) {
		lbc->lcrr |= 0x80000000;	/* DLL Bypass */

	} else if (lbc_hz >= 133) {
		lbc->lcrr &= (~0x80000000);		/* DLL Enabled */

	} else {
		lbc->lcrr &= (~0x8000000);	/* DLL Enabled */
		udelay(200);

		/*
		 * Sample LBC DLL ctrl reg, upshift it to set the
		 * override bits.
		 */
		temp_lbcdll = gur->lbcdllcr;
		gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000);
		asm("sync;isync;msync");
	}
}

/*
 * Initialize SDRAM memory on the Local Bus.
 */
void
sdram_init(void)
{
#if defined(CFG_OR2_PRELIM) && defined(CFG_BR2_PRELIM)

	uint idx;
	volatile ccsr_lbc_t *lbc = (void *)(CFG_MPC85xx_LBC_ADDR);
	uint *sdram_addr = (uint *)CFG_LBC_SDRAM_BASE;
	uint cpu_board_rev;
	uint lsdmr_common;

	puts("    SDRAM: ");

	print_size (CFG_LBC_SDRAM_SIZE * 1024 * 1024, "\n");

	/*
	 * Setup SDRAM Base and Option Registers
	 */
	lbc->or2 = CFG_OR2_PRELIM;
	asm("msync");

	lbc->br2 = CFG_BR2_PRELIM;
	asm("msync");

	lbc->lbcr = CFG_LBC_LBCR;
	asm("msync");

	lbc->lsrt = CFG_LBC_LSRT;
	lbc->mrtpr = CFG_LBC_MRTPR;
	asm("msync");

	/*
	 * Determine which address lines to use baed on CPU board rev.
	 */
	cpu_board_rev = get_cpu_board_revision();
	lsdmr_common = CFG_LBC_LSDMR_COMMON;
	if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_0) {
		lsdmr_common |= CFG_LBC_LSDMR_BSMA1617;
	} else if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_1) {
		lsdmr_common |= CFG_LBC_LSDMR_BSMA1516;
	} else {
		/*
		 * Assume something unable to identify itself is
		 * really old, and likely has lines 16/17 mapped.
		 */
		lsdmr_common |= CFG_LBC_LSDMR_BSMA1617;
	}

	/*
	 * Issue PRECHARGE ALL command.
	 */
	lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_PCHALL;
	asm("sync;msync");
	*sdram_addr = 0xff;
	ppcDcbf((unsigned long) sdram_addr);
	udelay(100);

	/*
	 * Issue 8 AUTO REFRESH commands.
	 */
	for (idx = 0; idx < 8; idx++) {
		lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_ARFRSH;
		asm("sync;msync");
		*sdram_addr = 0xff;
		ppcDcbf((unsigned long) sdram_addr);
		udelay(100);
	}

	/*
	 * Issue 8 MODE-set command.
	 */
	lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_MRW;
	asm("sync;msync");
	*sdram_addr = 0xff;
	ppcDcbf((unsigned long) sdram_addr);
	udelay(100);

	/*
	 * Issue NORMAL OP command.
	 */
	lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_NORMAL;
	asm("sync;msync");
	*sdram_addr = 0xff;
	ppcDcbf((unsigned long) sdram_addr);
	udelay(200);    /* Overkill. Must wait > 200 bus cycles */

#endif	/* enable SDRAM init */
}

#ifdef CONFIG_PCI
/* For some reason the Tundra PCI bridge shows up on itself as a
 * different device.  Work around that by refusing to configure it
 */
void dummy_func(struct pci_controller* hose, pci_dev_t dev, struct pci_config_table *tab) { }

static struct pci_config_table pci_mpc85xxcds_config_table[] = {
	{0x10e3, 0x0513, PCI_ANY_ID, 1, 3, PCI_ANY_ID, dummy_func, {0,0,0}},
	{0x1106, 0x0686, PCI_ANY_ID, 1, VIA_ID, 0, mpc85xx_config_via, {0,0,0}},
	{0x1106, 0x0571, PCI_ANY_ID, 1, VIA_ID, 1,
		mpc85xx_config_via_usbide, {0,0,0}},
	{0x1105, 0x3038, PCI_ANY_ID, 1, VIA_ID, 2,
		mpc85xx_config_via_usb, {0,0,0}},
	{0x1106, 0x3038, PCI_ANY_ID, 1, VIA_ID, 3,
		mpc85xx_config_via_usb2, {0,0,0}},
	{0x1106, 0x3058, PCI_ANY_ID, 1, VIA_ID, 5,
		mpc85xx_config_via_power, {0,0,0}},
	{0x1106, 0x3068, PCI_ANY_ID, 1, VIA_ID, 6,
		mpc85xx_config_via_ac97, {0,0,0}},
	{},
};


static struct pci_controller hose[] = {
	{
	config_table: pci_mpc85xxcds_config_table,
	},
#ifdef CONFIG_MPC85XX_PCI2
	{},
#endif
};

#endif

void
pci_init_board(void)
{
#ifdef CONFIG_PCI
	pci_mpc85xx_init(hose);
#endif
}

#if defined(CONFIG_OF_BOARD_SETUP)
void
ft_pci_setup(void *blob, bd_t *bd)
{
	int node, tmp[2];
	const char *path;

	node = fdt_path_offset(blob, "/aliases");
	tmp[0] = 0;
	if (node >= 0) {
#ifdef CONFIG_PCI1
		path = fdt_getprop(blob, node, "pci0", NULL);
		if (path) {
			tmp[1] = hose[0].last_busno - hose[0].first_busno;
			do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
		}
#endif
#ifdef CONFIG_MPC85XX_PCI2
		path = fdt_getprop(blob, node, "pci1", NULL);
		if (path) {
			tmp[1] = hose[1].last_busno - hose[1].first_busno;
			do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
		}
#endif
	}
}
#endif