example_280xecana_to_b_xmit.c

DSP学习板上的例子程序包括 AD转换 CAN总线 SPI SCI

// TI File $Revision: /main/4 $
// Checkin $Date: December 3, 2004   13:58:06 $
//###########################################################################
// Filename: Example_28xEcan_A_to_B_Xmit.c
//                                                                 
// Description: eCAN-A To eCAN-B TXLOOP - Transmit loop  	
//
// ASSUMPTIONS:
//
//    This program requires the DSP280x header files.  
//
//    Both CAN ports of the 280x DSP need to be connected 
//    to each other (via CAN transceivers)
//
//       eCANA is on GPIO31 (CANTXA)  and
//                   GPIO30 (CANRXA)
//
//       eCANB is on GPIO8  (CANTXB)  and
//                   GPIO10 (CANRXB)                 
//
//    As supplied, this project is configured for "boot to SARAM" 
//    operation.  The 280x Boot Mode table is shown below.  
//    For information on configuring the boot mode of an eZdsp, 
//    please refer to the documentation included with the eZdsp,  
//
//       Boot      GPIO18     GPIO29    GPIO34
//       Mode      SPICLKA    SCITXDA
//                 SCITXB
//       -------------------------------------
//       Flash       1          1        1
//       SCI-A       1          1        0
//       SPI-A       1          0        1
//       I2C-A       1          0        0
//       ECAN-A      0          1        1        
//       SARAM       0          1        0  <- "boot to SARAM"
//       OTP         0          0        1
//       I/0         0          0        0 
//
//
// DESCRIPTION:   
// 
//    This example TRANSMITS data to another CAN module using MAILBOX5
//    This program could either loop forever or transmit "n" # of times,	
//    where "n" is the TXCOUNT value.
//          
//    This example can be used to check CAN-A and CAN-B. Since CAN-B is
//    initialized in DSP280x_ECan.c, it will acknowledge all frames 
//    transmitted by the node on which this code runs. Both CAN ports of 
//    the 280x DSP need to be connected to each other (via CAN transceivers)
//
//###########################################################################
// Original Author: HJ
//
// $TI Release: DSP280x, DSP2801x Header Files V1.41 $
// $Release Date: August 7th, 2006 $
//###########################################################################

#include "DSP280x_Device.h"     // DSP280x Headerfile Include File
#include "DSP280x_Examples.h"   // DSP280x Examples Include File

#define TXCOUNT  100  // Transmission will take place (TXCOUNT) times..

// Globals for this example
long      i;
long 	  loopcount = 0;


void main()
{

/* Create a shadow register structure for the CAN control registers. This is
 needed, since, only 32-bit access is allowed to these registers. 16-bit access
 to these registers could potentially corrupt the register contents. This is
 especially true while writing to a bit (or group of bits) among bits 16 - 31 */

   struct ECAN_REGS ECanaShadow;

// Step 1. Initialize System Control:
// PLL, WatchDog, enable Peripheral Clocks
// This example function is found in the DSP280x_SysCtrl.c file.
   InitSysCtrl();

// Step 2. Initalize GPIO: 
// This example function is found in the DSP280x_Gpio.c file and
// illustrates how to set the GPIO to it's default state.
// InitGpio();  // Skipped for this example  

   // Just initalize eCAN pins for this example
   // This function is in DSP280x_ECan.c
   InitECanGpio();	

// Step 3. Clear all interrupts and initialize PIE vector table:
// Disable CPU interrupts 
   DINT;

// Initialize the PIE control registers to their default state.
// The default state is all PIE interrupts disabled and flags
// are cleared.  
// This function is found in the DSP280x_PieCtrl.c file.
   InitPieCtrl();
   
// Disable CPU interrupts and clear all CPU interrupt flags:
   IER = 0x0000;
   IFR = 0x0000;

// Initialize the PIE vector table with pointers to the shell Interrupt 
// Service Routines (ISR).  
// This will populate the entire table, even if the interrupt
// is not used in this example.  This is useful for debug purposes.
// The shell ISR routines are found in DSP280x_DefaultIsr.c.
// This function is found in DSP280x_PieVect.c.
   InitPieVectTable();

// Interrupts that are used in this example are re-mapped to
// ISR functions found within this file.  

// No interrupts used in this example.

// Step 4. Initialize all the Device Peripherals:
// This function is found in DSP280x_InitPeripherals.c
// InitPeripherals(); // Not required for this example
   
   // In this case just initalize eCAN-A and eCAN-B
   // This function is in DSP280x_ECan.c
   InitECan();
	
// Step 5. User specific code:

/* Write to the MSGID field  */
    
   ECanaMboxes.MBOX25.MSGID.all = 0x95555555; // Extended Identifier
       
/* Configure Mailbox under test as a Transmit mailbox */

   ECanaShadow.CANMD.all = ECanaRegs.CANMD.all;	
   ECanaShadow.CANMD.bit.MD25 = 0;
   ECanaRegs.CANMD.all = ECanaShadow.CANMD.all; 
	
/* Enable Mailbox under test */
	
   ECanaShadow.CANME.all = ECanaRegs.CANME.all;	
   ECanaShadow.CANME.bit.ME25 = 1;
   ECanaRegs.CANME.all = ECanaShadow.CANME.all; 
	
/* Write to DLC field in Master Control reg */

   ECanaMboxes.MBOX25.MSGCTRL.bit.DLC = 8;
	
/* Write to the mailbox RAM field */
    
   ECanaMboxes.MBOX25.MDL.all = 0x55555555;
   ECanaMboxes.MBOX25.MDH.all = 0x55555555;	 
	 	
/* Begin transmitting */


   for(i=0; i < TXCOUNT; i++)		    		  	
   {
       ECanaShadow.CANTRS.all = 0; 	
       ECanaShadow.CANTRS.bit.TRS25 = 1;     // Set TRS for mailbox under test       
       ECanaRegs.CANTRS.all = ECanaShadow.CANTRS.all; 
        
       while(ECanaRegs.CANTA.bit.TA25 == 0 ) {}  // Wait for TA5 bit to be set..
     
       ECanaShadow.CANTA.all = 0; 	
       ECanaShadow.CANTA.bit.TA25 = 1;     	 // Clear TA5       
       ECanaRegs.CANTA.all = ECanaShadow.CANTA.all;
     
       loopcount ++; 			    
    }  
     asm(" ESTOP0");  // Stop here
}