uart.c

该程序是演示ＡＲＭ的５个ＡＤＣ转换功能

#include <stm32f10x_lib.h>              /* STM32F10x Library Definitions      */                 
#include <stdio.h>

extern unsigned char Clock1s;
extern int  SendChar (int ch);         
void _ttywrch (int ch) { SendChar(ch); }
void _sys_exit (int return_code) { for (;;); }

int fputc (int ch, FILE *f) { return (SendChar(ch)); }
int ferror (FILE *f) {
  /* Your implementation of ferror */
  return EOF;
} 

GPIO_InitTypeDef  GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;

void SetupClock (void)
{
  RCC_DeInit ();                        /* RCC system reset(for debug purpose)*/
  RCC_HSEConfig (RCC_HSE_ON);           /* Enable HSE                         */

  /* Wait till HSE is ready                                                   */
  while (RCC_GetFlagStatus(RCC_FLAG_HSERDY) == RESET);

  RCC_HCLKConfig   (RCC_SYSCLK_Div1);   /* HCLK   = SYSCLK                    */
  RCC_PCLK2Config  (RCC_HCLK_Div1);     /* PCLK2  = HCLK                      */
  RCC_PCLK1Config  (RCC_HCLK_Div2);     /* PCLK1  = HCLK/2                    */
  RCC_ADCCLKConfig (RCC_PCLK2_Div4);    /* ADCCLK = PCLK2/4                   */

  *(vu32 *)0x40022000 = 0x01;           /* Flash 2 wait state                 */

  /* PLLCLK = 8MHz * 9 = 72 MHz                                               */
  RCC_PLLConfig (RCC_PLLSource_HSE_Div1, RCC_PLLMul_9);

  RCC_PLLCmd (ENABLE);                  /* Enable PLL                         */

  /* Wait till PLL is ready                                                   */
  while (RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET);

  /* Select PLL as system clock source                                        */
  RCC_SYSCLKConfig (RCC_SYSCLKSource_PLLCLK);

  /* Wait till PLL is used as system clock source                             */
  while (RCC_GetSYSCLKSource() != 0x08);

  /* Enable USART1 and GPIOA clock                                            */
  RCC_APB2PeriphClockCmd (RCC_APB2Periph_USART1 | RCC_APB2Periph_GPIOA, ENABLE);

  /* SysTick event each 10 ms with input clock equal to 9MHz (HCLK/8)         */
  SysTick_SetReload(90000);

  SysTick_ITConfig(ENABLE);             /* Enable SysTick interrupt           */
}


void SetupUART (void)  {

  GPIO_InitTypeDef  GPIO_InitStructure;
  USART_InitTypeDef USART_InitStructure;

  /* Enable GPIOA clock                                                       */
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);

  /* Configure USART1 Rx (PA10) as input floating                             */
  GPIO_InitStructure.GPIO_Pin   = GPIO_Pin_10;
  GPIO_InitStructure.GPIO_Mode  = GPIO_Mode_IN_FLOATING;
  GPIO_Init(GPIOA, &GPIO_InitStructure);

  /* Configure USART1 Tx (PA9) as alternate function push-pull                */
  GPIO_InitStructure.GPIO_Pin   = GPIO_Pin_9;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_Mode  = GPIO_Mode_AF_PP;
  GPIO_Init(GPIOA, &GPIO_InitStructure);

  /* USART1 configured as follow:
        - BaudRate = 115200 baud  
        - Word Length = 8 Bits
        - One Stop Bit
        - No parity
        - Hardware flow control disabled (RTS and CTS signals)
        - Receive and transmit enabled
        - USART Clock disabled
        - USART CPOL: Clock is active low
        - USART CPHA: Data is captured on the middle 
        - USART LastBit: The clock pulse of the last data bit is not output to 
                         the SCLK pin
  */
  USART_InitStructure.USART_BaudRate            = 115200;
  USART_InitStructure.USART_WordLength          = USART_WordLength_8b;
  USART_InitStructure.USART_StopBits            = USART_StopBits_1;
  USART_InitStructure.USART_Parity              = USART_Parity_No ;
  USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
  USART_InitStructure.USART_Mode                = USART_Mode_Rx | USART_Mode_Tx;
  USART_InitStructure.USART_Clock               = USART_Clock_Disable;
  USART_InitStructure.USART_CPOL                = USART_CPOL_Low;
  USART_InitStructure.USART_CPHA                = USART_CPHA_2Edge;
  USART_InitStructure.USART_LastBit             = USART_LastBit_Disable;
  USART_Init(USART1, &USART_InitStructure);

  USART_Cmd(USART1, ENABLE); 
             /* Enable USART1                      */
   }


   /* Implementation of putchar (also used by printf function to output data)    */
int SendChar (int ch)  {                /* Write character to Serial Port     */

  USART_SendData(USART1, (unsigned char) ch);
  while (!(USART1->SR & USART_FLAG_TXE));
  return (ch);
}
/******************* (C) COPYRIGHT 2007 STMicroelectronics *****END OF FILE****/