e1000_defines.h

DELL755 Intel 网卡驱动

#define E1000_MANC_REPORT_STATUS 0x00040000 /* Status Reporting Enabled */
#define E1000_MANC_RCV_ALL       0x00080000 /* Receive All Enabled */
#define E1000_MANC_BLK_PHY_RST_ON_IDE   0x00040000 /* Block phy resets */
/* Enable MAC address filtering */
#define E1000_MANC_EN_MAC_ADDR_FILTER   0x00100000
/* Enable MNG packets to host memory */
#define E1000_MANC_EN_MNG2HOST   0x00200000
/* Enable IP address filtering */
#define E1000_MANC_EN_IP_ADDR_FILTER    0x00400000
#define E1000_MANC_EN_XSUM_FILTER   0x00800000 /* Enable checksum filtering */
#define E1000_MANC_BR_EN            0x01000000 /* Enable broadcast filtering */
#define E1000_MANC_SMB_REQ       0x01000000 /* SMBus Request */
#define E1000_MANC_SMB_GNT       0x02000000 /* SMBus Grant */
#define E1000_MANC_SMB_CLK_IN    0x04000000 /* SMBus Clock In */
#define E1000_MANC_SMB_DATA_IN   0x08000000 /* SMBus Data In */
#define E1000_MANC_SMB_DATA_OUT  0x10000000 /* SMBus Data Out */
#define E1000_MANC_SMB_CLK_OUT   0x20000000 /* SMBus Clock Out */

#define E1000_MANC_SMB_DATA_OUT_SHIFT  28 /* SMBus Data Out Shift */
#define E1000_MANC_SMB_CLK_OUT_SHIFT   29 /* SMBus Clock Out Shift */

/* Receive Control */
#define E1000_RCTL_RST            0x00000001    /* Software reset */
#define E1000_RCTL_EN             0x00000002    /* enable */
#define E1000_RCTL_SBP            0x00000004    /* store bad packet */
#define E1000_RCTL_UPE            0x00000008    /* unicast promiscuous enable */
#define E1000_RCTL_MPE            0x00000010    /* multicast promiscuous enab */
#define E1000_RCTL_LPE            0x00000020    /* long packet enable */
#define E1000_RCTL_LBM_NO         0x00000000    /* no loopback mode */
#define E1000_RCTL_LBM_MAC        0x00000040    /* MAC loopback mode */
#define E1000_RCTL_LBM_SLP        0x00000080    /* serial link loopback mode */
#define E1000_RCTL_LBM_TCVR       0x000000C0    /* tcvr loopback mode */
#define E1000_RCTL_DTYP_MASK      0x00000C00    /* Descriptor type mask */
#define E1000_RCTL_DTYP_PS        0x00000400    /* Packet Split descriptor */
#define E1000_RCTL_RDMTS_HALF     0x00000000    /* rx desc min threshold size */
#define E1000_RCTL_RDMTS_QUAT     0x00000100    /* rx desc min threshold size */
#define E1000_RCTL_RDMTS_EIGTH    0x00000200    /* rx desc min threshold size */
#define E1000_RCTL_MO_SHIFT       12            /* multicast offset shift */
#define E1000_RCTL_MO_0           0x00000000    /* multicast offset 11:0 */
#define E1000_RCTL_MO_1           0x00001000    /* multicast offset 12:1 */
#define E1000_RCTL_MO_2           0x00002000    /* multicast offset 13:2 */
#define E1000_RCTL_MO_3           0x00003000    /* multicast offset 15:4 */
#define E1000_RCTL_MDR            0x00004000    /* multicast desc ring 0 */
#define E1000_RCTL_BAM            0x00008000    /* broadcast enable */
/* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */
#define E1000_RCTL_SZ_2048        0x00000000    /* rx buffer size 2048 */
#define E1000_RCTL_SZ_1024        0x00010000    /* rx buffer size 1024 */
#define E1000_RCTL_SZ_512         0x00020000    /* rx buffer size 512 */
#define E1000_RCTL_SZ_256         0x00030000    /* rx buffer size 256 */
/* these buffer sizes are valid if E1000_RCTL_BSEX is 1 */
#define E1000_RCTL_SZ_16384       0x00010000    /* rx buffer size 16384 */
#define E1000_RCTL_SZ_8192        0x00020000    /* rx buffer size 8192 */
#define E1000_RCTL_SZ_4096        0x00030000    /* rx buffer size 4096 */
#define E1000_RCTL_VFE            0x00040000    /* vlan filter enable */
#define E1000_RCTL_CFIEN          0x00080000    /* canonical form enable */
#define E1000_RCTL_CFI            0x00100000    /* canonical form indicator */
#define E1000_RCTL_DPF            0x00400000    /* discard pause frames */
#define E1000_RCTL_PMCF           0x00800000    /* pass MAC control frames */
#define E1000_RCTL_BSEX           0x02000000    /* Buffer size extension */
#define E1000_RCTL_SECRC          0x04000000    /* Strip Ethernet CRC */
#define E1000_RCTL_FLXBUF_MASK    0x78000000    /* Flexible buffer size */
#define E1000_RCTL_FLXBUF_SHIFT   27            /* Flexible buffer shift */

/*
 * Use byte values for the following shift parameters
 * Usage:
 *     psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) &
 *                  E1000_PSRCTL_BSIZE0_MASK) |
 *                ((ROUNDUP(value1, 1024) >> E1000_PSRCTL_BSIZE1_SHIFT) &
 *                  E1000_PSRCTL_BSIZE1_MASK) |
 *                ((ROUNDUP(value2, 1024) << E1000_PSRCTL_BSIZE2_SHIFT) &
 *                  E1000_PSRCTL_BSIZE2_MASK) |
 *                ((ROUNDUP(value3, 1024) << E1000_PSRCTL_BSIZE3_SHIFT) |;
 *                  E1000_PSRCTL_BSIZE3_MASK))
 * where value0 = [128..16256],  default=256
 *       value1 = [1024..64512], default=4096
 *       value2 = [0..64512],    default=4096
 *       value3 = [0..64512],    default=0
 */

#define E1000_PSRCTL_BSIZE0_MASK   0x0000007F
#define E1000_PSRCTL_BSIZE1_MASK   0x00003F00
#define E1000_PSRCTL_BSIZE2_MASK   0x003F0000
#define E1000_PSRCTL_BSIZE3_MASK   0x3F000000

#define E1000_PSRCTL_BSIZE0_SHIFT  7            /* Shift _right_ 7 */
#define E1000_PSRCTL_BSIZE1_SHIFT  2            /* Shift _right_ 2 */
#define E1000_PSRCTL_BSIZE2_SHIFT  6            /* Shift _left_ 6 */
#define E1000_PSRCTL_BSIZE3_SHIFT 14            /* Shift _left_ 14 */

/* SWFW_SYNC Definitions */
#define E1000_SWFW_EEP_SM   0x1
#define E1000_SWFW_PHY0_SM  0x2
#define E1000_SWFW_PHY1_SM  0x4
#define E1000_SWFW_CSR_SM   0x8

/* FACTPS Definitions */
#define E1000_FACTPS_LFS    0x40000000  /* LAN Function Select */
/* Device Control */
#define E1000_CTRL_FD       0x00000001  /* Full duplex.0=half; 1=full */
#define E1000_CTRL_BEM      0x00000002  /* Endian Mode.0=little,1=big */
#define E1000_CTRL_PRIOR    0x00000004  /* Priority on PCI. 0=rx,1=fair */
#define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */
#define E1000_CTRL_LRST     0x00000008  /* Link reset. 0=normal,1=reset */
#define E1000_CTRL_TME      0x00000010  /* Test mode. 0=normal,1=test */
#define E1000_CTRL_SLE      0x00000020  /* Serial Link on 0=dis,1=en */
#define E1000_CTRL_ASDE     0x00000020  /* Auto-speed detect enable */
#define E1000_CTRL_SLU      0x00000040  /* Set link up (Force Link) */
#define E1000_CTRL_ILOS     0x00000080  /* Invert Loss-Of Signal */
#define E1000_CTRL_SPD_SEL  0x00000300  /* Speed Select Mask */
#define E1000_CTRL_SPD_10   0x00000000  /* Force 10Mb */
#define E1000_CTRL_SPD_100  0x00000100  /* Force 100Mb */
#define E1000_CTRL_SPD_1000 0x00000200  /* Force 1Gb */
#define E1000_CTRL_BEM32    0x00000400  /* Big Endian 32 mode */
#define E1000_CTRL_FRCSPD   0x00000800  /* Force Speed */
#define E1000_CTRL_FRCDPX   0x00001000  /* Force Duplex */
#define E1000_CTRL_D_UD_EN  0x00002000  /* Dock/Undock enable */
#define E1000_CTRL_D_UD_POLARITY 0x00004000 /* Defined polarity of Dock/Undock indication in SDP[0] */
#define E1000_CTRL_FORCE_PHY_RESET 0x00008000 /* Reset both PHY ports, through PHYRST_N pin */
#define E1000_CTRL_EXT_LINK_EN 0x00010000 /* enable link status from external LINK_0 and LINK_1 pins */
#define E1000_CTRL_SWDPIN0  0x00040000  /* SWDPIN 0 value */
#define E1000_CTRL_SWDPIN1  0x00080000  /* SWDPIN 1 value */
#define E1000_CTRL_SWDPIN2  0x00100000  /* SWDPIN 2 value */
#define E1000_CTRL_SWDPIN3  0x00200000  /* SWDPIN 3 value */
#define E1000_CTRL_SWDPIO0  0x00400000  /* SWDPIN 0 Input or output */
#define E1000_CTRL_SWDPIO1  0x00800000  /* SWDPIN 1 input or output */
#define E1000_CTRL_SWDPIO2  0x01000000  /* SWDPIN 2 input or output */
#define E1000_CTRL_SWDPIO3  0x02000000  /* SWDPIN 3 input or output */
#define E1000_CTRL_RST      0x04000000  /* Global reset */
#define E1000_CTRL_RFCE     0x08000000  /* Receive Flow Control enable */
#define E1000_CTRL_TFCE     0x10000000  /* Transmit flow control enable */
#define E1000_CTRL_RTE      0x20000000  /* Routing tag enable */
#define E1000_CTRL_VME      0x40000000  /* IEEE VLAN mode enable */
#define E1000_CTRL_PHY_RST  0x80000000  /* PHY Reset */
#define E1000_CTRL_SW2FW_INT 0x02000000  /* Initiate an interrupt to manageability engine */
#define E1000_CTRL_I2C_ENA  0x02000000  /* I2C enable */

/* Bit definitions for the Management Data IO (MDIO) and Management Data
 * Clock (MDC) pins in the Device Control Register.
 */
#define E1000_CTRL_PHY_RESET_DIR  E1000_CTRL_SWDPIO0
#define E1000_CTRL_PHY_RESET      E1000_CTRL_SWDPIN0
#define E1000_CTRL_MDIO_DIR       E1000_CTRL_SWDPIO2
#define E1000_CTRL_MDIO           E1000_CTRL_SWDPIN2
#define E1000_CTRL_MDC_DIR        E1000_CTRL_SWDPIO3
#define E1000_CTRL_MDC            E1000_CTRL_SWDPIN3
#define E1000_CTRL_PHY_RESET_DIR4 E1000_CTRL_EXT_SDP4_DIR
#define E1000_CTRL_PHY_RESET4     E1000_CTRL_EXT_SDP4_DATA

#define E1000_CONNSW_ENRGSRC             0x4
#define E1000_PCS_CFG_PCS_EN             8
#define E1000_PCS_LCTL_FLV_LINK_UP       1
#define E1000_PCS_LCTL_FSV_10            0
#define E1000_PCS_LCTL_FSV_100           2
#define E1000_PCS_LCTL_FSV_1000          4
#define E1000_PCS_LCTL_FDV_FULL          8
#define E1000_PCS_LCTL_FSD               0x10
#define E1000_PCS_LCTL_FORCE_LINK        0x20
#define E1000_PCS_LCTL_LOW_LINK_LATCH    0x40
#define E1000_PCS_LCTL_AN_ENABLE         0x10000
#define E1000_PCS_LCTL_AN_RESTART        0x20000
#define E1000_PCS_LCTL_AN_TIMEOUT        0x40000
#define E1000_PCS_LCTL_AN_SGMII_BYPASS   0x80000
#define E1000_PCS_LCTL_AN_SGMII_TRIGGER  0x100000
#define E1000_PCS_LCTL_FAST_LINK_TIMER   0x1000000
#define E1000_PCS_LCTL_LINK_OK_FIX       0x2000000
#define E1000_PCS_LCTL_CRS_ON_NI         0x4000000
#define E1000_ENABLE_SERDES_LOOPBACK     0x0410

#define E1000_PCS_LSTS_LINK_OK           1
#define E1000_PCS_LSTS_SPEED_10          0
#define E1000_PCS_LSTS_SPEED_100         2
#define E1000_PCS_LSTS_SPEED_1000        4
#define E1000_PCS_LSTS_DUPLEX_FULL       8
#define E1000_PCS_LSTS_SYNK_OK           0x10
#define E1000_PCS_LSTS_AN_COMPLETE       0x10000
#define E1000_PCS_LSTS_AN_PAGE_RX        0x20000
#define E1000_PCS_LSTS_AN_TIMED_OUT      0x40000
#define E1000_PCS_LSTS_AN_REMOTE_FAULT   0x80000
#define E1000_PCS_LSTS_AN_ERROR_RWS      0x100000

/* Device Status */
#define E1000_STATUS_FD         0x00000001      /* Full duplex.0=half,1=full */
#define E1000_STATUS_LU         0x00000002      /* Link up.0=no,1=link */
#define E1000_STATUS_FUNC_MASK  0x0000000C      /* PCI Function Mask */
#define E1000_STATUS_FUNC_SHIFT 2
#define E1000_STATUS_FUNC_0     0x00000000      /* Function 0 */
#define E1000_STATUS_FUNC_1     0x00000004      /* Function 1 */
#define E1000_STATUS_TXOFF      0x00000010      /* transmission paused */
#define E1000_STATUS_TBIMODE    0x00000020      /* TBI mode */
#define E1000_STATUS_SPEED_MASK 0x000000C0
#define E1000_STATUS_SPEED_10   0x00000000      /* Speed 10Mb/s */
#define E1000_STATUS_SPEED_100  0x00000040      /* Speed 100Mb/s */
#define E1000_STATUS_SPEED_1000 0x00000080      /* Speed 1000Mb/s */
#define E1000_STATUS_LAN_INIT_DONE 0x00000200   /* Lan Init Completion by NVM */
#define E1000_STATUS_ASDV       0x00000300      /* Auto speed detect value */
#define E1000_STATUS_DOCK_CI    0x00000800      /* Change in Dock/Undock state. Clear on write '0'. */
#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */
#define E1000_STATUS_MTXCKOK    0x00000400      /* MTX clock running OK */
#define E1000_STATUS_PCI66      0x00000800      /* In 66Mhz slot */
#define E1000_STATUS_BUS64      0x00001000      /* In 64 bit slot */
#define E1000_STATUS_PCIX_MODE  0x00002000      /* PCI-X mode */
#define E1000_STATUS_PCIX_SPEED 0x0000C000      /* PCI-X bus speed */
#define E1000_STATUS_BMC_SKU_0  0x00100000 /* BMC USB redirect disabled */
#define E1000_STATUS_BMC_SKU_1  0x00200000 /* BMC SRAM disabled */
#define E1000_STATUS_BMC_SKU_2  0x00400000 /* BMC SDRAM disabled */
#define E1000_STATUS_BMC_CRYPTO 0x00800000 /* BMC crypto disabled */
#define E1000_STATUS_BMC_LITE   0x01000000 /* BMC external code execution disabled */
#define E1000_STATUS_RGMII_ENABLE 0x02000000 /* RGMII disabled */
#define E1000_STATUS_FUSE_8       0x04000000
#define E1000_STATUS_FUSE_9       0x08000000
#define E1000_STATUS_SERDES0_DIS  0x10000000 /* SERDES disabled on port 0 */
#define E1000_STATUS_SERDES1_DIS  0x20000000 /* SERDES disabled on port 1 */

/* Constants used to interpret the masked PCI-X bus speed. */
#define E1000_STATUS_PCIX_SPEED_66  0x00000000 /* PCI-X bus speed  50-66 MHz */
#define E1000_STATUS_PCIX_SPEED_100 0x00004000 /* PCI-X bus speed  66-100 MHz */
#define E1000_STATUS_PCIX_SPEED_133 0x00008000 /* PCI-X bus speed 100-133 MHz */

#define SPEED_10    10
#define SPEED_100   100
#define SPEED_1000  1000
#define HALF_DUPLEX 1
#define FULL_DUPLEX 2

#define PHY_FORCE_TIME   20

#define ADVERTISE_10_HALF                 0x0001
#define ADVERTISE_10_FULL                 0x0002
#define ADVERTISE_100_HALF                0x0004
#define ADVERTISE_100_FULL                0x0008
#define ADVERTISE_1000_HALF               0x0010 /* Not used, just FYI */
#define ADVERTISE_1000_FULL               0x0020

/* 1000/H is not supported, nor spec-compliant. */
#define E1000_ALL_SPEED_DUPLEX ( ADVERTISE_10_HALF |   ADVERTISE_10_FULL | \
                                ADVERTISE_100_HALF |  ADVERTISE_100_FULL | \
                                                     ADVERTISE_1000_FULL)
#define E1000_ALL_NOT_GIG      ( ADVERTISE_10_HALF |   ADVERTISE_10_FULL | \
                                ADVERTISE_100_HALF |  ADVERTISE_100_FULL)
#define E1000_ALL_100_SPEED    (ADVERTISE_100_HALF |  ADVERTISE_100_FULL)
#define E1000_ALL_10_SPEED      (ADVERTISE_10_HALF |   ADVERTISE_10_FULL)
#define E1000_ALL_FULL_DUPLEX   (ADVERTISE_10_FULL |  ADVERTISE_100_FULL | \
                                                     ADVERTISE_1000_FULL)
#define E1000_ALL_HALF_DUPLEX   (ADVERTISE_10_HALF |  ADVERTISE_100_HALF)

#define AUTONEG_ADVERTISE_SPEED_DEFAULT   E1000_ALL_SPEED_DUPLEX

/* LED Control */
#define E1000_LEDCTL_LED0_MODE_MASK       0x0000000F
#define E1000_LEDCTL_LED0_MODE_SHIFT      0