cc1100_smartrf.h

用c8051f310开发的433M无线模块cc1100的完整程序

// Chipcon
// Product = CC1100
// Chip version = F   (VERSION = 0x03)
// Crystal accuracy = 10 ppm
// X-tal frequency = 26 MHz
// RF output power = 0 dBm
// RX filterbandwidth = 812.500000 kHz
// Phase = 0
// Datarate = 499.877930 kBaud
// Modulation = (7) MSK
// Manchester enable = (0) Manchester disabled
// RF Frequency = 433.099792 MHz
// Channel spacing = 199.951172 kHz
// Channel number = 0
// Optimization = -
// Sync mode = (3) 30/32 sync word bits detected
// Format of RX/TX data = (0) Normal mode, use FIFOs for RX and TX
// CRC operation = (1) CRC calculation in TX and CRC check in RX enabled
// Forward Error Correction = (0) FEC disabled
// Length configuration = (1) Variable length packets, packet length configured by the first received byte after sync word.
// Packetlength = 255
// Preamble count = (4)  8 bytes
// Append status = 1
// Address check = (0) No address check
// FIFO autoflush = 0
// Device address = 0
// GDO0 signal selection = ( 6) Asserts when sync word has been sent / received, and de-asserts at the end of the packet
// GDO2 signal selection = (41) CHIP_RDY

/***************************************************************
*
*  SmartRF Studio(tm) 输出文件
*
*  波特率＝500k/MSK
*
***************************************************************/

#ifndef CC1100_SMARTRF_H
#define CC1100_SMARTRF_H

//#define SMARTRF_RADIO_CC1100

#define SMARTRF_SETTING_FSCTRL1    0x0D
#define SMARTRF_SETTING_FSCTRL0    0x00
#define SMARTRF_SETTING_FREQ2      0x10
#define SMARTRF_SETTING_FREQ1      0xA8
#define SMARTRF_SETTING_FREQ0      0x5E
#define SMARTRF_SETTING_MDMCFG4    0x0E
#define SMARTRF_SETTING_MDMCFG3    0x3B
#define SMARTRF_SETTING_MDMCFG2    0x73		//允许DC阻隔、MSK、禁止曼切斯特码、检测30/32位同步字。
#define SMARTRF_SETTING_MDMCFG1    0x42		//禁止FEC、8字节前序。
#define SMARTRF_SETTING_MDMCFG0    0xF8
//#define SMARTRF_SETTING_CHANNR     0x00
#define SMARTRF_SETTING_DEVIATN    0x00
#define SMARTRF_SETTING_FREND1     0xB6
#define SMARTRF_SETTING_FREND0     0x10
#define SMARTRF_SETTING_MCSM0      0x18
#define SMARTRF_SETTING_FOCCFG     0x1D		//收发频率偏差补偿＝允许,前增益＝4K，后增益＝K/2，饱和点＝±BW/4。
#define SMARTRF_SETTING_BSCFG      0x1C
#define SMARTRF_SETTING_AGCCTRL2   0xC7		//最高增益设置禁用，最大可能的LAN增益、信道滤波器开口＝42dB。
#define SMARTRF_SETTING_AGCCTRL1   0x00
#define SMARTRF_SETTING_AGCCTRL0   0xB0		//ACG增益调节回差死区增益＝中、信道滤波器采样数量＝32、AGC增益控制＝调节、采样平均＝8次。
#define SMARTRF_SETTING_FSCAL3     0xEA
#define SMARTRF_SETTING_FSCAL2     0x2A
#define SMARTRF_SETTING_FSCAL1     0x00
#define SMARTRF_SETTING_FSCAL0     0x1F
#define SMARTRF_SETTING_FSTEST     0x59
#define SMARTRF_SETTING_TEST2      0x88
#define SMARTRF_SETTING_TEST1      0x31
#define SMARTRF_SETTING_TEST0      0x09
#define SMARTRF_SETTING_FIFOTHR    0x07
#define SMARTRF_SETTING_IOCFG2     0x29
#define SMARTRF_SETTING_IOCFG0D    0x06
#define SMARTRF_SETTING_PKTCTRL1   0x04
#define SMARTRF_SETTING_PKTCTRL0   0x05
#define SMARTRF_SETTING_ADDR       0x00
#define SMARTRF_SETTING_PKTLEN     0xFF

void CC1100_Config( void );

#endif