decnet-phiv-mib

很不错java的SNMP应用例子

     STATUS mandatory
     DESCRIPTION
         "Information about the currently known DECnet Phase
         IV Routes."
     INDEX  { phivLevel1RouteNodeAddr }
     ::= { phivLevel1RouteTable 1 }

PhivLevel1RouteEntry ::=
     SEQUENCE {
         phivLevel1RouteNodeAddr
             PhivAddr,
         phivLevel1RouteCircuitIndex
             INTEGER,
         phivLevel1RouteCost
             INTEGER,
         phivLevel1RouteHops
             INTEGER,
         phivLevel1RouteNextNode
             PhivAddr
     }

phivLevel1RouteNodeAddr OBJECT-TYPE
     SYNTAX PhivAddr -- OCTET STRING (SIZE (2))
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "This value is the address of the node about which
         routing information is contained in this level 1
         routing table."
     ::= { phivLevel1RouteEntry 1 }

phivLevel1RouteCircuitIndex OBJECT-TYPE
     SYNTAX INTEGER (1..65535)
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "A unique index value for each known circuit. This is
         the index to the circuit state table and is the same
         value as phivCircuitIndex."
     ::= { phivLevel1RouteEntry 2 }

phivLevel1RouteCost OBJECT-TYPE
     SYNTAX INTEGER (0..65535)
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "This read-only parameter represents the total cost
         over the current path to the destination node. Cost is
         a positive integer value associated with using a
         circuit. Routing routes messages (data) along the path
         between two nodes with the smallest cost. COST is kept
         on a remote node basis."
     ::= { phivLevel1RouteEntry 3 }

phivLevel1RouteHops OBJECT-TYPE
     SYNTAX INTEGER (0..127)
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "This read-only parameter represents the number of hops
         over to a destination node. A hop is Routing value
         representing the logical distance between two nodes in
         a network. HOPS is kept on a remote node basis."
     ::= { phivLevel1RouteEntry 4 }

phivLevel1RouteNextNode OBJECT-TYPE
     SYNTAX PhivAddr -- OCTET STRING (SIZE (2))
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "This read-only value indicates the next node on the
         circuit used to get to the node under scrutiny
         (next hop)."
     ::= { phivLevel1RouteEntry 5 }

-- Additional routing parameters

phivRouteCountZeroCount OBJECT-TYPE
     SYNTAX INTEGER {
         other (1),
         reset (2)
     }
     ACCESS read-write
     STATUS mandatory
     DESCRIPTION
         "When this value is set to 2, the following objects are
         set to Zero: phivRouteCountAgedPktLoss,
         phivRouteCountNodeUnrPktLoss,
         phivRouteCountOutRngePktLoss,
         phivRouteCountOverSzePktLoss,
         phivRouteCountPacketFmtErr,
         phivRouteCountPtlRteUpdtLoss, and
         phivRouteCountVerifReject."
     ::= { routing 23 }

phivRouteSystemAddr OBJECT-TYPE
     SYNTAX PhivAddr -- OCTET STRING (SIZE (2))
     ACCESS read-only
     STATUS obsolete
     DESCRIPTION
         "DECnet Phase IV node address."
     ::= { routing 24 }

phivRouteRoutingType OBJECT-TYPE
     SYNTAX INTEGER {
         routing-III (1),
         nonrouting-III (2),
         area (3),
         routing-IV (4),
         nonrouting-IV (5)
     }
     ACCESS read-write
     STATUS mandatory
     DESCRIPTION
         "This read-write parameter indicates the type of the executor
         node. The node-type is one of the following:

         routing-III
         nonrouting-III
         routing-IV
         ronrouting-IV
         area

         A routing node has full routing capability. A
         nonrouting node contains a subset of the Routing
         routing modules. The III and IV indicate the DNA
         phase of the node. Nonrouting nodes can deliver
         and receive packets to and from any node, but cannot
         route packets from other nodes through to other nodes.
         An area node routes between areas. Refer to the Routing
         specification for details.

         For adjacent nodes, this is a read-only parameter that
         indicates the type of the reachable adjacent node.
         NOTE: The ROUTING-III and NONROUTING-III values are
         incremented by one compared to the standard DECnet
         values in order to maintain compliance with RFC 1155)"
     ::= { routing 25 }

phivRouteSystemAddress OBJECT-TYPE
     SYNTAX PhivAddr -- OCTET STRING (SIZE (2))
     ACCESS read-write
     STATUS mandatory
     DESCRIPTION
         "DECnet Phase IV node address."
     ::= { routing 26 }

-- Circuit Group

-- The implementation of the Circuit Group is mandatory for
-- all systems.

-- Circuit Parameters Table

phivCircuitParametersTable OBJECT-TYPE
     SYNTAX SEQUENCE OF PhivCircuitParametersEntry
     ACCESS not-accessible
     STATUS mandatory
     DESCRIPTION
         "Information about the parameters associated with all
         circuits currently known."
     ::= {circuit 1 }

phivCircuitParametersEntry OBJECT-TYPE
     SYNTAX PhivCircuitParametersEntry
     ACCESS not-accessible
     STATUS mandatory
     DESCRIPTION
         "Parameters information about all circuits currently
          known."
     INDEX  { phivCircuitIndex }
     ::= { phivCircuitParametersTable 1 }

PhivCircuitParametersEntry ::=
     SEQUENCE {
         phivCircuitIndex
             INTEGER,
         phivCircuitLineIndex
             INTEGER,
         phivCircuitCommonState
             INTEGER,
         phivCircuitCommonSubState
             INTEGER,
         phivCircuitCommonName
             DisplayString,
         phivCircuitExecRecallTimer
             INTEGER,
         phivCircuitCommonType
             INTEGER,
         phivCircuitService
             INTEGER,
         phivCircuitExecCost
             INTEGER,
         phivCircuitExecHelloTimer
             INTEGER
    }

phivCircuitIndex OBJECT-TYPE
     SYNTAX INTEGER (1..65535)
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "A unique index value for each known circuit."
     ::= { phivCircuitParametersEntry 1 }

phivCircuitLineIndex OBJECT-TYPE
     SYNTAX InterfaceIndex
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "The line on which this circuit is active.  This is
          the same as the ifIndex."
     ::= { phivCircuitParametersEntry 2 }

phivCircuitCommonState OBJECT-TYPE
     SYNTAX INTEGER {
         on (1),
         off (2),
         service (3),
         cleared (4)
     }
     ACCESS read-write
     STATUS mandatory
     DESCRIPTION
         "This value represents the circuit's Network Management
         operational state. NOTE: These values are incremented
         by one compared to the standard DECnet values in order
         to maintain compliance with RFC 1155."
     ::= { phivCircuitParametersEntry 3 }

phivCircuitCommonSubState OBJECT-TYPE
     SYNTAX INTEGER {
         starting (1),
         reflecting (2),
         looping (3),
         loading (4),
         dumping (5),
         triggering (6),
         autoservice (7),
         autoloading (8),
         autodumping (9),
         autotriggering (10),
         synchronizing (11),
         failed (12),
         running (13)
     }
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "This value represents the circuit's Network Management
         operational and service substate. NOTE: These values are
         incremented by one compared to the standard DECnet values
         in order to maintain compliance with RFC 1155."
     ::= { phivCircuitParametersEntry 4 }

phivCircuitCommonName OBJECT-TYPE
     SYNTAX DisplayString (SIZE (0..16))
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "The name of the circuit entry in the table, for example,
          SVA-0 or in a level 2 router ASYNC-8 or ETHER-1)."
     ::= { phivCircuitParametersEntry 5 }

phivCircuitExecRecallTimer OBJECT-TYPE
     SYNTAX INTEGER (0..65535)
     ACCESS read-write
     STATUS mandatory
     DESCRIPTION
         "This parameter represents the minimum number of
         seconds to wait before restarting the circuit.  A
         value of 0 indicates not timer is running."
     ::= { phivCircuitParametersEntry 6 }

phivCircuitCommonType OBJECT-TYPE
     SYNTAX INTEGER {
         ddcmp-point (1),
         ddcmp-control (2),
         ddcmp-tributary (3),
         x25 (4),
         ddcmp-dmc (5),
         ethernet (6),
         ci (7),
         qp2-dte20 (8),
         bisync (9),
         other (14),
         fddi (15)
     }
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "Represents the type of the circuit. For X.25 circuits,
         the value must be set to X25. For DDCMP and Ethernet
         circuits it is read only and is the same value as the
         protocol of the associated line.
         NOTE: Values 1 - 5 are incremented by one compared to the
         standard DECnet values in order to maintain compliance
         with RFC 1155."
     ::= { phivCircuitParametersEntry 7 }

phivCircuitService  OBJECT-TYPE
     SYNTAX INTEGER {
         enabled (1),
         disabled (2)
     }
     ACCESS read-write
     STATUS mandatory
     DESCRIPTION
         "This value indicates whether or not Network Management
         allows service operations on a circuit. The values for
         service-control are as follows:

         ENABLED     SERVICE state and/or service functions are
                     allowed.

         DISABLED    SERVICE state and/or service functions are not
                     allowed.

         NOTE: These values are incremented by one compared to the
         standard DECnet values in order to maintain compliance
         with RFC 1155."
     ::= { phivCircuitParametersEntry 8 }

phivCircuitExecCost OBJECT-TYPE
     SYNTAX INTEGER (1..25)
     ACCESS read-write
     STATUS mandatory
     DESCRIPTION
         "This value represents the routing cost of the circuit.
         Routing sends messages along the path between two nodes
         having the smallest cost."
     ::= { phivCircuitParametersEntry 9 }

phivCircuitExecHelloTimer OBJECT-TYPE
     SYNTAX INTEGER (1..8191)
     ACCESS read-write
     STATUS mandatory
     DESCRIPTION
         "This value determines the frequency of Routing Hello
         messages sent to the adjacent node on the circuit."
     ::= { phivCircuitParametersEntry 10 }

-- Circuit Counters Table

phivCircuitCountTable OBJECT-TYPE
     SYNTAX SEQUENCE OF PhivCircuitCountEntry
     ACCESS not-accessible
     STATUS mandatory
     DESCRIPTION
         "Information about the counters associated with all
         circuits currently known."
     ::= { circuit 2 }

       phivCircuitCountEntry OBJECT-TYPE
     SYNTAX PhivCircuitCountEntry
     ACCESS not-accessible
     STATUS mandatory
     DESCRIPTION
         "Counter information about all circuits currently known"
     INDEX     { phivCircuitIndex }
     ::= { phivCircuitCountTable 1 }

PhivCircuitCountEntry ::=
     SEQUENCE {
         phivCircuitCountSecLastZeroed
             PhivCounter,
         phivCircuitCountTermPacketsRecd
             PhivCounter,
         phivCircuitCountOriginPackSent
             PhivCounter,
         phivCircuitCountTermCongLoss
             PhivCounter,
         phivCircuitCountCorruptLoss
             PhivCounter,
         phivCircuitCountTransitPksRecd
             PhivCounter,
         phivCircuitCountTransitPkSent
             PhivCounter,
         phivCircuitCountTransitCongestLoss
             PhivCounter,
         phivCircuitCountCircuitDown
             PhivCounter,
         phivCircuitCountInitFailure
             PhivCounter,
         phivCircuitCountAdjDown
             PhivCounter,
         phivCircuitCountPeakAdj
             PhivCounter,
         phivCircuitCountBytesRecd
             PhivCounter,
         phivCircuitCountBytesSent
             PhivCounter,
         phivCircuitCountDataBlocksRecd
             PhivCounter,
         phivCircuitCountDataBlocksSent
             PhivCounter,
         phivCircuitCountUsrBuffUnav
             PhivCounter
     }

phivCircuitCountSecLastZeroed  OBJECT-TYPE
     SYNTAX PhivCounter (0..65535)
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "Number of seconds since the circuit counters for this
         circuit were last zeroed."
     ::= { phivCircuitCountEntry 1 }

phivCircuitCountTermPacketsRecd OBJECT-TYPE
     SYNTAX PhivCounter (0..2147483647)
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION