atm2-mib

很不错java的SNMP应用例子

        "The value of this object is equal to the
         ifIndex value for the ATM interface port for
         this SVCC cross-connect.  The term high implies
         that this ATM interface has the numerically
         higher ifIndex value than the other ATM interface
         identified in the same atmSvcVcCrossConnectEntry."
       ::= { atmSvcVcCrossConnectEntry 5 }

   atmSvcVcCrossConnectHighVpi OBJECT-TYPE



       SYNTAX       AtmVpIdentifier
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
        "The value of this object is equal to the VPI
         value associated with the SVCC cross-connect
         at the ATM interface that is identified by
         atmSvcVcCrossConnectHighIfIndex.  The VPI value
         cannot exceed the number supported by the
         atmInterfaceCurrentMaxSvccVpi at the high ATM interface
         port."
       ::= { atmSvcVcCrossConnectEntry 6 }

   atmSvcVcCrossConnectHighVci OBJECT-TYPE
       SYNTAX       AtmVcIdentifier
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
        "The value of this object is equal to the VCI
         value associated with the SVCC cross-connect
         at the ATM interface that is identified by
         atmSvcVcCrossConnectHighIfIndex.  The VCI value
         cannot exceed the number supported by the
         atmInterfaceMaxVciBits at the high ATM interface
         port."
       ::= { atmSvcVcCrossConnectEntry 7 }

   atmSvcVcCrossConnectCreationTime OBJECT-TYPE
       SYNTAX       TimeStamp
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
        "The value of the sysUpTime object
         at the time this bi-directional SVCC
         cross-connect was created.  If the current
         state was entered prior to the last
         re-initialization of the agent, then this
         object contains a zero value."
       ::= { atmSvcVcCrossConnectEntry 8 }

   atmSvcVcCrossConnectRowStatus OBJECT-TYPE
       SYNTAX       RowStatus
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           "This object is used to delete rows in the
            atmSvcVcCrossConnectTable."
       ::= { atmSvcVcCrossConnectEntry 9 }



   -- 3. ATM Interface Signalling Statistics Table --

   atmSigStatTable       OBJECT-TYPE
       SYNTAX       SEQUENCE OF AtmSigStatEntry
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
        "This table contains ATM interface signalling
        statistics, one entry per ATM signalling
        interface."
       ::= { atm2MIBObjects 3 }

   atmSigStatEntry         OBJECT-TYPE
       SYNTAX       AtmSigStatEntry
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
        "This list contains signalling statistics variables."
       INDEX { ifIndex }
       ::= { atmSigStatTable  1}

   AtmSigStatEntry    ::= SEQUENCE  {
       atmSigSSCOPConEvents            Counter32,
       atmSigSSCOPErrdPdus             Counter32,
       atmSigDetectSetupAttempts       Counter32,
       atmSigEmitSetupAttempts         Counter32,
       atmSigDetectUnavailRoutes       Counter32,
       atmSigEmitUnavailRoutes         Counter32,
       atmSigDetectUnavailResrcs       Counter32,
       atmSigEmitUnavailResrcs         Counter32,
       atmSigDetectCldPtyEvents        Counter32,
       atmSigEmitCldPtyEvents          Counter32,
       atmSigDetectMsgErrors           Counter32,
       atmSigEmitMsgErrors             Counter32,
       atmSigDetectClgPtyEvents        Counter32,
       atmSigEmitClgPtyEvents          Counter32,
       atmSigDetectTimerExpireds       Counter32,
       atmSigEmitTimerExpireds         Counter32,
       atmSigDetectRestarts            Counter32,
       atmSigEmitRestarts              Counter32,
       atmSigInEstabls                 Counter32,
       atmSigOutEstabls                Counter32
            }

   atmSigSSCOPConEvents   OBJECT-TYPE
       SYNTAX       Counter32
       MAX-ACCESS   read-only
       STATUS       current



       DESCRIPTION
           "SSCOP Connection Events Counter.  This counter counts
            the sum of the following errors:

            1) SSCOP Connection Disconnect Counter

                The abnormal occurrence of this event is
                characterized by the expiry of Timer_NO_RESPONSE.
                (This event is communicated to the layer management
                with MAA-ERROR code P.  See ITU-T Q.2110.)

             2) SSCOP Connection Initiation Failure

                This condition indicates the inability to establish
                an SSCOP connection.  This event occurs whenever the
                number of expiries of the connection control timer
                (Timer_CC) equals or exceeds the MaxCC, or upon
                receipt of a connection reject message BGREJ PDU.
                (This event is communicated to layer management with
                MAA-ERROR code O.  See ITU-T Q.2110.)

             3) SSCOP Connection Re-Establ/Resynch

                This event occurs upon receipt of a BGN PDU or
                RS PDU."
       REFERENCE
           "ITU-T Recommendation Q.2110, Broadband
            Integrated Services Digital Network
            (B-ISDN) - ATM Adaptation Layer - Service
            Specific Connection Oriented Protocol (SSCOP)
            Specification, July 1994."
       ::= { atmSigStatEntry 1}

   atmSigSSCOPErrdPdus   OBJECT-TYPE
       SYNTAX       Counter32
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
           "SSCOP Errored PDUs Counter.  This counter counts the
           sum of the following errors:

           1) Invalid PDUs.
              These are defined in SSCOP and consist of PDUs
              with an incorrect length (MAA-ERROR code U), an
              undefined PDU type code, or that are not 32-bit
              aligned.

           2) PDUs that result in MAA-ERROR codes and are



              discarded.

           See MAA-ERROR codes A-D, F-M, and Q-T defined in
           ITU-T Q.2110."
       REFERENCE
           "ITU-T Recommendation Q.2110, Broadband
            Integrated Services Digital Network
            (B-ISDN) - ATM Adaptation Layer - Service
            Specific Connection Oriented Protocol (SSCOP)
            Specification, July 1994."
       ::= { atmSigStatEntry 2 }

   atmSigDetectSetupAttempts    OBJECT-TYPE
       SYNTAX       Counter32
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
           "Call Setup Attempts Counter.  This counter counts
           the number of call setup attempts (both successful
           and unsuccessful) detected on this interface."
       ::= { atmSigStatEntry 3 }

   atmSigEmitSetupAttempts    OBJECT-TYPE
       SYNTAX       Counter32
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
           "Call Setup Attempts Counter.  This counter counts
           the number of call setup attempts (both successful
           and unsuccessful) transmitted on this interface."
       ::= { atmSigStatEntry 4 }

   atmSigDetectUnavailRoutes    OBJECT-TYPE
       SYNTAX       Counter32
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
           "Number of Route Unavailability detected on this interface.
           This counter is incremented when a RELEASE, RELEASE COMPLETE
           (only when not preceded by a RELEASE message for the same
           call), ADD PARTY REJECT, or STATUS message that
           contains one of the following cause code values is
           received (Note: These cause values
           apply to both UNI3.0 and UNI3.1):

           Cause Value            Meaning





              1            unallocated (unassigned) number
              2            no route to specified transit network
              3            no route to destination

           NOTE:  For this counter, RELEASE COMPLETE
           messages that are a reply to a previous RELEASE
           message and contain the same cause value, are
           redundant (for counting purposes) and should not
           be counted."

       ::= { atmSigStatEntry 5 }

   atmSigEmitUnavailRoutes    OBJECT-TYPE
       SYNTAX       Counter32
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
           "Number of Route Unavailability transmitted from this
           interface.  This counter is incremented when a RELEASE,
           RELEASE COMPLETE (only when not preceded by a RELEASE
           message for the same call), ADD PARTY REJECT, or
           STATUS message that contains one of the following cause
           code values is transmitted (Note: These cause values apply
           to both UNI3.0 and UNI3.1):

           Cause Value            Meaning

              1            unallocated (unassigned) number
              2            no route to specified transit network
              3            no route to destination

           NOTE:  For this counter, RELEASE COMPLETE
           messages that are a reply to a previous RELEASE
           message and contain the same cause value, are
           redundant (for counting purposes) and should not
           be counted."
       ::= { atmSigStatEntry 6 }

   atmSigDetectUnavailResrcs     OBJECT-TYPE
       SYNTAX       Counter32
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
           "Number of Resource Unavailability detected on this
           interface.  This counter is incremented when a RELEASE,
           RELEASE COMPLETE (only when not preceded by a RELEASE
           message for the same call), ADD PARTY REJECT, or
           STATUS message that contains one of the following



           cause code values is received (Note: These cause
           values apply to both UNI3.0 and UNI3.1 unless
           otherwise stated):

           Cause Value          Meaning

              35          requested VPCI/VCI not available
              37          user cell rate not available (UNI3.1
                          only)
              38          network out of order
              41          temporary failure
              45          no VPCI/VCI available
              47          resource unavailable, unspecified
              49          Quality of Service unavailable
              51          user cell rate not available (UNI3.0
                          only)
              58          bearer capability not presently
                          available
              63          Service or option not available,
                          unspecified
              92          too many pending add party requests

           NOTE:  For this counter, RELEASE COMPLETE
           messages that are a reply to a previous RELEASE
           message and contain the same cause value, are
           redundant (for counting purposes) and should not
           be counted."
       ::= { atmSigStatEntry 7 }

   atmSigEmitUnavailResrcs     OBJECT-TYPE
       SYNTAX       Counter32
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
          "Number of Resource Unavailability transmitted from this
          interface.  This counter is incremented when a RELEASE,
          RELEASE COMPLETE (only when not preceded by a RELEASE message
          for the same call), ADD PARTY REJECT, or STATUS message that
          contains one of the following cause code values is transmitted
          (Note: These cause values apply to both UNI3.0 and UNI3.1
          unless otherwise stated):

          Cause Value          Meaning

             35          requested VPCI/VCI not available
             37          user cell rate not available (UNI3.1
                         only)
             38          network out of order



             41          temporary failure
             45          no VPCI/VCI available
             47          resource unavailable, unspecified
             49          Quality of Service unavailable
             51          user cell rate not available (UNI3.0
                         only)
             58          bearer capability not presently
                         available
             63          Service or option not available,
                         unspecified
             92          too many pending add party requests

          NOTE:  For this counter, RELEASE COMPLETE messages that are a
          reply to a previous RELEASE message and contain the same cause
          value, are redundant (for counting purposes) and should not be
          counted."

      ::= { atmSigStatEntry 8 }

  atmSigDetectCldPtyEvents     OBJECT-TYPE
      SYNTAX       Counter32
      MAX-ACCESS   read-only
      STATUS       current
      DESCRIPTION
         "Number of Called Party Responsible For Unsuccessful Call
         detected on this interface.  This counter is incremented when a
         RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE
         message for the same call), ADD PARTY REJECT, or STATUS message
         that contains one of the following cause code values is
         received (Note: These cause values apply to both UNI3.0 and
         UNI3.1):

         Cause Value         Meaning

            17           user busy
            18           no user responding
            21           call rejected
            22           number changed
            23           user rejects all calls with calling
                         line identification restriction (CLIR)
            27           destination out of order
            31           normal, unspecified
            88           incompatible destination


         NOTE:  For this counter, RELEASE COMPLETE messages that are a
         reply to a previous RELEASE message and contain the same cause