vdsl-line-mib

很不错java的SNMP应用例子

                                 a valid frame.

        2   lossOfSignal         Vtu failure due to not receiving
                                 signal.

        3   lossOfPower          Vtu failure due to loss of power.

        4   lossOfSignalQuality  Loss of Signal Quality is declared
                                 when the Noise Margin falls below
                                 the Minimum Noise Margin, or the
                                 bit-error-rate exceeds 10^-7.

        5   lossOfLink           Vtu failure due to inability to
                                 link with peer Vtu.  Set whenever
                                 the transceiver is in the 'Warm
                                 Start' state.

        6   dataInitFailure      Vtu failure during initialization
                                 due to bit errors corrupting
                                 startup exchange data.




        7   configInitFailure    Vtu failure during initialization
                                 due to peer Vtu not able to
                                 support requested configuration.

        8   protocolInitFailure  Vtu failure during initialization
                                 due to incompatible protocol used
                                 by the peer Vtu.

        9   noPeerVtuPresent     Vtu failure during initialization
                                 due to no activation sequence
                                 detected from peer Vtu.

        This is intended to supplement ifOperStatus."
    REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
     ::= { vdslPhysEntry 7 }

vdslPhysCurrOutputPwr OBJECT-TYPE
    SYNTAX       Integer32 (0..160)
    UNITS        "0.1dBm"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Measured total output power transmitted by this VTU.
        This is the measurement that was reported during
        the last activation sequence."
    REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
    ::= { vdslPhysEntry 8 }

vdslPhysCurrAttainableRate OBJECT-TYPE
    SYNTAX       Gauge32
    UNITS        "kbps"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Indicates the maximum currently attainable data rate
        in steps of 1000 bits/second by the Vtu.  This value
        will be equal to or greater than vdslPhysCurrLineRate.
        Note that for SCM, the minimum and maximum data rates
        are equal.  Note: 1 kbps = 1000 bps."
    REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
    ::= { vdslPhysEntry 9 }

vdslPhysCurrLineRate OBJECT-TYPE
    SYNTAX       Gauge32
    UNITS        "kbps"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION



        "Indicates the current data rate in steps of 1000
        bits/second by the Vtu.  This value will be less than
        or equal to vdslPhysCurrAttainableRate.  Note: 1 kbps =
        1000 bps."
    REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
    ::= { vdslPhysEntry 10 }

vdslChanTable OBJECT-TYPE
    SYNTAX       SEQUENCE OF VdslChanEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "This table provides one row for each Vtu channel.
        VDSL channel interfaces are those ifEntries where
        ifType is equal to interleave(124) or fast(125)."
    ::= { vdslMibObjects 3 }

vdslChanEntry OBJECT-TYPE
    SYNTAX       VdslChanEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "An entry in the vdslChanTable."
    INDEX { ifIndex,
            vdslPhysSide }
    ::= { vdslChanTable 1 }

VdslChanEntry ::=
    SEQUENCE
        {
        vdslChanInterleaveDelay        Gauge32,
        vdslChanCrcBlockLength         Gauge32,
        vdslChanCurrTxRate             Gauge32,
        vdslChanCurrTxSlowBurstProtect Gauge32,
        vdslChanCurrTxFastFec          Gauge32
        }

vdslChanInterleaveDelay OBJECT-TYPE
    SYNTAX       Gauge32
    UNITS        "milliseconds"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Interleave Delay for this channel.

        Interleave delay applies only to the interleave
        (slow) channel and defines the mapping (relative
        spacing) between subsequent input bytes at the



        interleaver input and their placement in the bit
        stream at the interleaver output.  Larger numbers
        provide greater separation between consecutive
        input bytes in the output bit stream allowing for
        improved impulse noise immunity at the expense of
        payload latency.

        In the case where the ifType is fast(125), return
        a value of zero."
    REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
    ::= { vdslChanEntry 1 }

vdslChanCrcBlockLength OBJECT-TYPE
    SYNTAX       Gauge32
    UNITS        "bytes"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Indicates the length of the channel data-block
        on which the CRC operates."
    REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
    ::= { vdslChanEntry 2 }

vdslChanCurrTxRate OBJECT-TYPE
    SYNTAX       Gauge32
    UNITS        "kbps"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Actual transmit data rate on this channel.  Note: 1
        kbps = 1000 bps."
    ::= { vdslChanEntry 3 }

vdslChanCurrTxSlowBurstProtect OBJECT-TYPE
    SYNTAX       Gauge32 (0..1275)
    UNITS        "microseconds"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Actual level of impulse noise (burst) protection
        for an interleaved (slow) channel.  This parameter is
        not applicable to fast channels.  For fast channels,
        a value of zero shall be returned."
    REFERENCE    "ITU-T G.997.1, section 7.3.2.3"
    ::= { vdslChanEntry 4 }

vdslChanCurrTxFastFec OBJECT-TYPE
    SYNTAX       Gauge32 (0..50)



    UNITS        "%"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Actual Forward Error Correction (FEC) redundancy
        related overhead for a fast channel.  This parameter
        is not applicable to an interleaved (slow) channel.
        For interleaved channels, a value of zero shall be
        returned."
    ::= { vdslChanEntry 5 }

vdslPerfDataTable       OBJECT-TYPE
    SYNTAX       SEQUENCE OF VdslPerfDataEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "This table provides one row for each VDSL physical
        interface.  VDSL physical interfaces are those ifEntries
        where ifType is equal to vdsl(97)."
    ::= { vdslMibObjects 4 }

vdslPerfDataEntry       OBJECT-TYPE
    SYNTAX        VdslPerfDataEntry
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "An entry in the vdslPerfDataTable."
    INDEX { ifIndex,
            vdslPhysSide }
    ::= { vdslPerfDataTable 1 }

VdslPerfDataEntry ::=
    SEQUENCE
        {
        vdslPerfDataValidIntervals         HCPerfValidIntervals,
        vdslPerfDataInvalidIntervals       HCPerfInvalidIntervals,
        vdslPerfDataLofs                   Unsigned32,
        vdslPerfDataLoss                   Unsigned32,
        vdslPerfDataLprs                   Unsigned32,
        vdslPerfDataLols                   Unsigned32,
        vdslPerfDataESs                    Unsigned32,
        vdslPerfDataSESs                   Unsigned32,
        vdslPerfDataUASs                   Unsigned32,
        vdslPerfDataInits                  Unsigned32,
        vdslPerfDataCurr15MinTimeElapsed   HCPerfTimeElapsed,
        vdslPerfDataCurr15MinLofs          HCPerfCurrentCount,
        vdslPerfDataCurr15MinLoss          HCPerfCurrentCount,
        vdslPerfDataCurr15MinLprs          HCPerfCurrentCount,



        vdslPerfDataCurr15MinLols          HCPerfCurrentCount,
        vdslPerfDataCurr15MinESs           HCPerfCurrentCount,
        vdslPerfDataCurr15MinSESs          HCPerfCurrentCount,
        vdslPerfDataCurr15MinUASs          HCPerfCurrentCount,
        vdslPerfDataCurr15MinInits         HCPerfCurrentCount,
        vdslPerfData1DayValidIntervals     HCPerfValidIntervals,
        vdslPerfData1DayInvalidIntervals   HCPerfInvalidIntervals,
        vdslPerfDataCurr1DayTimeElapsed    HCPerfTimeElapsed,
        vdslPerfDataCurr1DayLofs           Unsigned32,
        vdslPerfDataCurr1DayLoss           Unsigned32,
        vdslPerfDataCurr1DayLprs           Unsigned32,
        vdslPerfDataCurr1DayLols           Unsigned32,
        vdslPerfDataCurr1DayESs            Unsigned32,
        vdslPerfDataCurr1DaySESs           Unsigned32,
        vdslPerfDataCurr1DayUASs           Unsigned32,
        vdslPerfDataCurr1DayInits          Unsigned32
        }

vdslPerfDataValidIntervals OBJECT-TYPE
    SYNTAX       HCPerfValidIntervals
    UNITS        "intervals"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Valid Intervals per definition found in
        HC-PerfHist-TC-MIB."
    ::= { vdslPerfDataEntry 1 }

vdslPerfDataInvalidIntervals OBJECT-TYPE
    SYNTAX       HCPerfInvalidIntervals
    UNITS        "intervals"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Invalid Intervals per definition found in
        HC-PerfHist-TC-MIB."
    ::= { vdslPerfDataEntry 2 }

vdslPerfDataLofs OBJECT-TYPE
    SYNTAX       Unsigned32
    UNITS        "seconds"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Count of seconds since the unit was last reset that there
        was Loss of Framing."
    REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
    ::= { vdslPerfDataEntry 3 }



vdslPerfDataLoss OBJECT-TYPE
    SYNTAX       Unsigned32
    UNITS        "seconds"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Count of seconds since the unit was last reset that there
        was Loss of Signal."
    REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
    ::= { vdslPerfDataEntry 4 }

vdslPerfDataLprs OBJECT-TYPE
    SYNTAX       Unsigned32
    UNITS        "seconds"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Count of seconds since the unit was last reset that there
        was Loss of Power."

    REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
    ::= { vdslPerfDataEntry 5 }

vdslPerfDataLols OBJECT-TYPE
    SYNTAX       Unsigned32
    UNITS        "seconds"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Count of seconds since the unit was last reset that there
        was Loss of Link."
    ::= { vdslPerfDataEntry 6 }

vdslPerfDataESs OBJECT-TYPE
    SYNTAX       Unsigned32
    UNITS        "seconds"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Count of Errored Seconds since the unit was last reset.
        An Errored Second is a one-second interval containing one
        or more CRC anomalies, or one or more LOS or LOF defects."
    REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
    ::= { vdslPerfDataEntry 7 }

vdslPerfDataSESs OBJECT-TYPE
    SYNTAX       Unsigned32
    UNITS        "seconds"



    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Count of Severely Errored Seconds since the unit was last
        reset."
    ::= { vdslPerfDataEntry 8 }

vdslPerfDataUASs OBJECT-TYPE
    SYNTAX       Unsigned32
    UNITS        "seconds"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Count of Unavailable Seconds since the unit was last
        reset."
    ::= { vdslPerfDataEntry 9 }

vdslPerfDataInits OBJECT-TYPE
    SYNTAX       Unsigned32
    UNITS        "occurrences"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Count of the line initialization attempts since the unit
        was last reset.  This count includes both successful and
        failed attempts."
    REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
    ::= { vdslPerfDataEntry 10 }

vdslPerfDataCurr15MinTimeElapsed OBJECT-TYPE
    SYNTAX       HCPerfTimeElapsed
    UNITS        "seconds"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Total elapsed seconds in this interval."
    ::= { vdslPerfDataEntry 11 }

vdslPerfDataCurr15MinLofs OBJECT-TYPE
    SYNTAX       HCPerfCurrentCount
    UNITS        "seconds"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Count of seconds during this interval that there
        was Loss of Framing."
    REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
    ::= { vdslPerfDataEntry 12 }



vdslPerfDataCurr15MinLoss OBJECT-TYPE
    SYNTAX       HCPerfCurrentCount
    UNITS        "seconds"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Count of seconds during this interval that there
        was Loss of Signal."
    REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
    ::= { vdslPerfDataEntry 13 }

vdslPerfDataCurr15MinLprs OBJECT-TYPE
    SYNTAX       HCPerfCurrentCount
    UNITS        "seconds"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "Count of seconds during this interval that there
        was Loss of Power."
    REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
    ::= { vdslPerfDataEntry 14 }

vdslPerfDataCurr15MinLols OBJECT-TYPE
    SYNTAX       HCPerfCurrentCount