auxio.h

this SRC packet is the headfiles that MIZI vivi bootloader needed when compling

/* $Id: auxio.h,v 1.18 1997/11/07 15:01:45 jj Exp $
 * auxio.h:  Definitions and code for the Auxiliary I/O register.
 *
 * Copyright (C) 1995 David S. Miller ([e-mail])
 */
#ifndef _SPARC_AUXIO_H
#define _SPARC_AUXIO_H

#include <asm/system.h>
#include <asm/vaddrs.h>

extern unsigned char *auxio_register;

/* This register is an unsigned char in IO space.  It does two things.
 * First, it is used to control the front panel LED light on machines
 * that have it (good for testing entry points to trap handlers and irq's)
 * Secondly, it controls various floppy drive parameters.
 */
#define AUXIO_ORMEIN      0xf0    /* All writes must set these bits. */
#define AUXIO_ORMEIN4M    0xc0    /* sun4m - All writes must set these bits. */
#define AUXIO_FLPY_DENS   0x20    /* Floppy density, high if set. Read only. */
#define AUXIO_FLPY_DCHG   0x10    /* A disk change occurred.  Read only. */
#define AUXIO_EDGE_ON     0x10    /* sun4m - On means Jumper block is in. */
#define AUXIO_FLPY_DSEL   0x08    /* Drive select/start-motor. Write only. */
#define AUXIO_LINK_TEST   0x08    /* sun4m - On means TPE Carrier detect. */

/* Set the following to one, then zero, after doing a pseudo DMA transfer. */
#define AUXIO_FLPY_TCNT   0x04    /* Floppy terminal count. Write only. */

/* Set the following to zero to eject the floppy. */
#define AUXIO_FLPY_EJCT   0x02    /* Eject floppy disk.  Write only. */
#define AUXIO_LED         0x01    /* On if set, off if unset. Read/Write */

#define AUXREG   ((volatile unsigned char *)(auxio_register))

/* These are available on sun4c */
#define TURN_ON_LED   if (AUXREG) *AUXREG = (*AUXREG | AUXIO_ORMEIN | AUXIO_LED)
#define TURN_OFF_LED  if (AUXREG) *AUXREG = ((*AUXREG | AUXIO_ORMEIN) & (~AUXIO_LED))
#define FLIP_LED      if (AUXREG) *AUXREG = ((*AUXREG | AUXIO_ORMEIN) ^ AUXIO_LED)
#define FLPY_MOTORON  if (AUXREG) *AUXREG = ((*AUXREG | AUXIO_ORMEIN) | AUXIO_FLPY_DSEL)
#define FLPY_MOTOROFF if (AUXREG) *AUXREG = ((*AUXREG | AUXIO_ORMEIN) & (~AUXIO_FLPY_DSEL))
#define FLPY_TCNTON   if (AUXREG) *AUXREG = ((*AUXREG | AUXIO_ORMEIN) | AUXIO_FLPY_TCNT)
#define FLPY_TCNTOFF  if (AUXREG) *AUXREG = ((*AUXREG | AUXIO_ORMEIN) & (~AUXIO_FLPY_TCNT))

#ifndef __ASSEMBLY__
#define set_auxio(bits_on, bits_off) \
do { \
	unsigned char regval; \
	unsigned long flags; \
	save_flags(flags); cli(); \
	switch(sparc_cpu_model) { \
	case sun4c: \
		regval = *AUXREG; \
		*AUXREG = ((regval | bits_on) & ~bits_off) | AUXIO_ORMEIN; \
		break; \
	case sun4m: \
		if(!AUXREG) \
			break;     /* VME chassic sun4m, no auxio. */ \
		regval = *AUXREG; \
		*AUXREG = ((regval | bits_on) & ~bits_off) | AUXIO_ORMEIN4M; \
		break; \
	case sun4d: \
		break; \
	default: \
		panic("Can't set AUXIO register on this machine."); \
	}; \
	restore_flags(flags); \
} while(0)
#endif /* !(__ASSEMBLY__) */


/* AUXIO2 (Power Off Control) */
extern __volatile__ unsigned char * auxio_power_register;

#define	AUXIO_POWER_DETECT_FAILURE	32
#define	AUXIO_POWER_CLEAR_FAILURE	2
#define	AUXIO_POWER_OFF			1


#endif /* !(_SPARC_AUXIO_H) */