📄 44binit.s
字号:
bl Main ;从汇编进入C语言代码空间，不要使用main()
b .
CODE32
]
LTORG
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;中断向量表 ;
;Example: HandlerADC HANDLE HandleADC 解为 ;
;HandlerADC ;HandlerADC为中断向量表的入口 ;
; sub sp,sp,#4 ;将sp减少一个字节，使其在堆栈高端留出存储返回地址，因为pc在寄存器组中的 ;
; ;的位置大于r0，出栈时装入的是栈的高端的内容 ;
; stmfd sp!,{r0} ;保存r0 ;
; ldr r0,=HandleADC ;装载中断处理函数的指针 ;
; ldr r0,[r0] ;装载中断处理函数的地址 ;
; str r0,[sp,#4] ;将中断处理函数的地址存入刚才预留的位置，r0的上面 ;
; ldmfd sp!,{r0,pc} ;出栈后，pc指向的既是中断处理函数的地址 ;
; ;
; INTCON^2 == 0时,vector table使能 ;
; 发生中断->HandlerADC->HandleADC(pISR_ADC,即:_ISR_STARTADDRESS+0x20); ;
; 若要在程序中处理此中断，只要将中断服务函数的指针赋给pISR_ADC,如：pISR_ADC = (int)ADCIsr ;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
HandlerFIQ HANDLER HandleFIQ
HandlerIRQ HANDLER HandleIRQ
HandlerUndef HANDLER HandleUndef
HandlerSWI HANDLER HandleSWI
HandlerDabort HANDLER HandleDabort
HandlerPabort HANDLER HandlePabort
HandlerADC HANDLER HandleADC
HandlerRTC HANDLER HandleRTC
HandlerUTXD1 HANDLER HandleUTXD1
HandlerUTXD0 HANDLER HandleUTXD0
HandlerSIO HANDLER HandleSIO
HandlerIIC HANDLER HandleIIC
HandlerURXD1 HANDLER HandleURXD1
HandlerURXD0 HANDLER HandleURXD0
HandlerTIMER5 HANDLER HandleTIMER5
HandlerTIMER4 HANDLER HandleTIMER4
HandlerTIMER3 HANDLER HandleTIMER3
HandlerTIMER2 HANDLER HandleTIMER2
HandlerTIMER1 HANDLER HandleTIMER1
HandlerTIMER0 HANDLER HandleTIMER0
HandlerUERR01 HANDLER HandleUERR01
HandlerWDT HANDLER HandleWDT
HandlerBDMA1 HANDLER HandleBDMA1
HandlerBDMA0 HANDLER HandleBDMA0
HandlerZDMA1 HANDLER HandleZDMA1
HandlerZDMA0 HANDLER HandleZDMA0
HandlerTICK HANDLER HandleTICK
HandlerEINT4567 HANDLER HandleEINT4567
HandlerEINT3 HANDLER HandleEINT3
HandlerEINT2 HANDLER HandleEINT2
HandlerEINT1 HANDLER HandleEINT1
HandlerEINT0 HANDLER HandleEINT0
;***********************************************
IMPORT |Image$$RO$$Base| ; ROM code start
IMPORT |Image$$RO$$Limit| ; RAM data starts after ROM program
IMPORT |Image$$RW$$Base| ; Pre-initialised variables
IMPORT |Image$$ZI$$Base| ; uninitialised variables
IMPORT |Image$$ZI$$Limit| ; End of variable RAM space
BaseOfROM DCD |Image$$RO$$Base|
TopOfROM DCD |Image$$RO$$Limit|
BaseOfBSS DCD |Image$$RW$$Base|
BaseOfZero DCD |Image$$ZI$$Base|
EndOfBSS DCD |Image$$ZI$$Limit|
EXPORT GetBaseOfROM
EXPORT GetEndOfROM
EXPORT GetBaseOfBSS
EXPORT GetBaseOfZero
EXPORT GetEndOfBSS
GetBaseOfROM
ldr r0, BaseOfROM
mov pc, lr
GetEndOfROM
ldr r0, TopOfROM
mov pc, lr
GetBaseOfBSS
ldr r0, BaseOfBSS
mov pc, lr
GetBaseOfZero
ldr r0, BaseOfZero
mov pc, lr
GetEndOfBSS
ldr r0, EndOfBSS
mov pc, lr
;****************************************************
;* The function for initializing stack *
;****************************************************
InitStacks
;Do not use DRAM,such as stmfd,ldmfd......
;SVCstack is initialized before
;Under toolkit ver 2.50, 'msr cpsr,r1' can be used instead of 'msr cpsr_cxsf,r1'
mrs r0,cpsr
bic r0,r0,#MODEMASK
orr r1,r0,#UNDEFMODE|NOINT
msr cpsr_cxsf,r1 ;UndefMode
ldr sp,=UndefStack
orr r1,r0,#ABORTMODE|NOINT
msr cpsr_cxsf,r1 ;AbortMode
ldr sp,=AbortStack
orr r1,r0,#IRQMODE|NOINT
msr cpsr_cxsf,r1 ;IRQMode
ldr sp,=IRQStack
orr r1,r0,#FIQMODE|NOINT
msr cpsr_cxsf,r1 ;FIQMode
ldr sp,=FIQStack
bic r0,r0,#MODEMASK|NOINT
orr r1,r0,#SVCMODE
msr cpsr_cxsf,r1 ;SVCMode
ldr sp,=SVCStack
;USER mode is not initialized.
mov pc,lr ;The LR register may be not valid for the mode changes.
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;非向量中断的处理 ;
;如果I_ISPC的使用不正确，此时I_ISPR可能为零 ;
;堆栈内容的变化 ;
; ;
;H sp |--| |--| |--| |--| sp |--| ;
; | | sp | | | | |ad|->pc | | ;
; | | | | |r9| |r9|->r9 | | ;
;L | | | | sp |r8| sp |r8|->r8 | | ;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
IsrIRQ ;using I_ISPR register.
sub sp,sp,#4 ;reserved for PC
stmfd sp!,{r8-r9}
;IMPORTANT CAUTION
;if I_ISPC is not used properly, I_ISPR can be 0 in this routine.
ldr r9,=I_ISPR
ldr r9,[r9]
cmp r9, #0x0 ;If the IDLE mode work-around is used,
;r9 may be 0 sometimes.
beq %F2
mov r8,#0x0
0
movs r9,r9,lsr #1
bcs %F1
add r8,r8,#4
b %B0
1
ldr r9,=HandleADC
add r9,r9,r8
ldr r9,[r9]
str r9,[sp,#8]
ldmfd sp!,{r8-r9,pc}
2
ldmfd sp!,{r8-r9}
add sp,sp,#4
subs pc,lr,#4
;****************************************************
;* The function for entering power down mode *
;****************************************************
;void EnterPWDN(int CLKCON);
EnterPWDN
mov r2,r0 ;r0=CLKCON
ldr r0,=REFRESH
ldr r3,[r0]
mov r1, r3
orr r1, r1, #0x400000 ;self-refresh enable
str r1, [r0]
nop ;Wait until self-refresh is issued. May not be needed.
nop ;If the other bus master holds the bus, ...
nop ; mov r0, r0
nop
nop
nop
nop
;enter POWERDN mode
ldr r0,=CLKCON
str r2,[r0]
;wait until enter SL_IDLE,STOP mode and until wake-up
mov r0,#0xff
0 subs r0,r0,#1
bne %B0
;exit from DRAM/SDRAM self refresh mode.
ldr r0,=REFRESH
str r3,[r0]
mov pc,lr
LTORG
SMRDATA DATA
;*****************************************************************
; Memory configuration has to be optimized for best performance *
; The following parameter is not optimized. *
;*****************************************************************
;*** memory access cycle parameter strategy ***
; 1) Even FP-DRAM, EDO setting has more late fetch point by half-clock
; 2) The memory settings,here, are made the safe parameters even at 66Mhz.
; 3) FP-DRAM Parameters:tRCD=3 for tRAC, tcas=2 for pad delay, tcp=2 for bus load.
; 4) DRAM refresh rate is for 40Mhz.
;bank0 16bit BOOT ROM SST39VF160/SST39VF320
;bank1 8bit Nand Flash K9F2808U0A/K9F5608U0A
;bank2 16bit USB1.1 PDIUSBD12
;bank3 RTL8019
;bank4 No Uesed
;bank5 No Uesed
;bank6 16bit SDRAM
;bank7 16bit SDRAM
[ BUSWIDTH=16
; DCD 0x11111111 ;Bank0=OM[1:0], Bank0~Bank7=16bit
DCD 0x11111001 ;Bank0=OM[1:0] 16bit BootRomSST39VF160/SST39VF320) :0x0
; |||||||- Bank1=8bit Nand Flash
; |||||--- Bank2=8bit PDIUSBD12
; ||||---- Bank3=16bit RTL8019
; |||----- Bank4~5=16bit No Uesd
; -------- Bank6~7=16bit SDRAM
| ;BUSWIDTH=32
DCD 0x22222220 ;Bank0=OM[1:0], Bank1~Bank7=32bit
]
DCD ((B0_Tacs<<13)+(B0_Tcos<<11)+(B0_Tacc<<8)+(B0_Tcoh<<6)+(B0_Tah<<4)+(B0_Tacp<<2)+(B0_PMC)) ;GCS0
DCD ((B1_Tacs<<13)+(B1_Tcos<<11)+(B1_Tacc<<8)+(B1_Tcoh<<6)+(B1_Tah<<4)+(B1_Tacp<<2)+(B1_PMC)) ;GCS1
DCD ((B2_Tacs<<13)+(B2_Tcos<<11)+(B2_Tacc<<8)+(B2_Tcoh<<6)+(B2_Tah<<4)+(B2_Tacp<<2)+(B2_PMC)) ;GCS2
DCD ((B3_Tacs<<13)+(B3_Tcos<<11)+(B3_Tacc<<8)+(B3_Tcoh<<6)+(B3_Tah<<4)+(B3_Tacp<<2)+(B3_PMC)) ;GCS3
DCD ((B4_Tacs<<13)+(B4_Tcos<<11)+(B4_Tacc<<8)+(B4_Tcoh<<6)+(B4_Tah<<4)+(B4_Tacp<<2)+(B4_PMC)) ;GCS4
DCD ((B5_Tacs<<13)+(B5_Tcos<<11)+(B5_Tacc<<8)+(B5_Tcoh<<6)+(B5_Tah<<4)+(B5_Tacp<<2)+(B5_PMC)) ;GCS5
[ BDRAMTYPE="DRAM"
DCD ((B6_MT<<15)+(B6_Trcd<<4)+(B6_Tcas<<3)+(B6_Tcp<<2)+(B6_CAN)) ;GCS6 check the MT value in parameter.a
DCD ((B7_MT<<15)+(B7_Trcd<<4)+(B7_Tcas<<3)+(B7_Tcp<<2)+(B7_CAN)) ;GCS7
| ;"SDRAM"
DCD ((B6_MT<<15)+(B6_Trcd<<2)+(B6_SCAN)) ;GCS6
DCD ((B7_MT<<15)+(B7_Trcd<<2)+(B7_SCAN)) ;GCS7
]
DCD ((REFEN<<23)+(TREFMD<<22)+(Trp<<20)+(Trc<<18)+(Tchr<<16)+REFCNT) ;REFRESH RFEN=1, TREFMD=0, trp=3clk, trc=5clk, tchr=3clk,count=1019
DCD 0x07 ;SCLK power down mode, BANKSIZE 32M/32M
DCD 0x20 ;MRSR6 CL=2clk
DCD 0x20 ;MRSR7
ALIGN
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;RW BEGIN;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
AREA RamData, DATA, READWRITE
^ (_ISR_STARTADDRESS-0x500)
UserStack # 256 ;c1(c7)ffa00
SVCStack # 256 ;c1(c7)ffb00
UndefStack # 256 ;c1(c7)ffc00
AbortStack # 256 ;c1(c7)ffd00
IRQStack # 256 ;c1(c7)ffe00
FIQStack # 0 ;c1(c7)fff00
^ _ISR_STARTADDRESS
HandleReset # 4
HandleUndef # 4
HandleSWI # 4
HandlePabort # 4
HandleDabort # 4
HandleReserved # 4
HandleIRQ # 4
HandleFIQ # 4
;Do not use the label 'IntVectorTable',
;because armasm.exe can not recognize this label correctly.
;the value is different with an address you think it may be.
;IntVectorTable
HandleADC # 4
HandleRTC # 4
HandleUTXD1 # 4
HandleUTXD0 # 4
HandleSIO # 4
HandleIIC # 4
HandleURXD1 # 4
HandleURXD0 # 4
HandleTIMER5 # 4
HandleTIMER4 # 4
HandleTIMER3 # 4
HandleTIMER2 # 4
HandleTIMER1 # 4
HandleTIMER0 # 4
HandleUERR01 # 4
HandleWDT # 4
HandleBDMA1 # 4
HandleBDMA0 # 4
HandleZDMA1 # 4
HandleZDMA0 # 4
HandleTICK # 4
HandleEINT4567 # 4
HandleEINT3 # 4
HandleEINT2 # 4
HandleEINT1 # 4
HandleEINT0 # 4 ;0xc1(c7)fff84
END
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -