reset_db1000.s

RMI的处理器au1200系列所用的BOOTLOAD,包括SD卡启动USB启动硬盘启动网络启动,并初始化硬件的所有参数,支持内核调试.

	/* RCE2 */
	li		t1, MEM_STCFG2
	sw		t1, mem_stcfg2(t0)
	li		t1, MEM_STTIME2
	sw		t1, mem_sttime2(t0)
	li		t1, MEM_STADDR2
	sw		t1, mem_staddr2(t0)

	/* RCE3 */
	li		t1, MEM_STCFG3
	sw		t1, mem_stcfg3(t0)
	li		t1, MEM_STTIME3
	sw		t1, mem_sttime3(t0)
	li		t1, MEM_STADDR3
	sw		t1, mem_staddr3(t0)

	sync

	/*
	 * Step 15) Set peripherals to a known state
	 */
	li		t0, AU1000_IC0_ADDR
	li		t1, 0xFFFFFFFF
	sw		t1, ic_cfg0clr(t0)
	sw		t1, ic_cfg1clr(t0)
	sw		t1, ic_cfg2clr(t0)
	sw		t1, ic_srcset(t0)
	sw		t1, ic_assignset(t0)
	sw		t1, ic_wakeclr(t0)
	sw		t1, ic_maskclr(t0)
	sw		t1, ic_risingclr(t0)
	sw		t1, ic_fallingclr(t0)
	sw		zero, ic_testbit(t0)
	sync

	li		t0, AU1000_IC1_ADDR
	li		t1, 0xFFFFFFFF
	sw		t1, ic_cfg0clr(t0)
	sw		t1, ic_cfg1clr(t0)
	sw		t1, ic_cfg2clr(t0)
	sw		t1, ic_srcset(t0)
	sw		t1, ic_assignset(t0)
	sw		t1, ic_wakeclr(t0)
	sw		t1, ic_maskclr(t0)
	sw		t1, ic_risingclr(t0)
	sw		t1, ic_fallingclr(t0)
	sw		zero, ic_testbit(t0)
	sync

	li		t0, AU1000_SYS_ADDR
	sw		zero, sys_freqctrl0(t0)
	sw		zero, sys_freqctrl1(t0)
	sw		zero, sys_clksrc(t0)
	sw		zero, sys_pininputen(t0)
	sync

	li		t0, AU1000_AC97_ADDR
	li		t1, 0x2
	sw		t1, ac97_enable(t0)
	sync

	li		t0, AU1000_USBH_ADDR
	li		t1, usbh_enable
	addu	t0, t1, t0
	sw		zero, 0(t0)
	sync

	li		t0, AU1000_USBD_ADDR
	sw		zero, usbd_enable(t0)
	sync

	li		t0, AU1000_IRDA_ADDR
	sw		zero, irda_enable(t0)
	sync

	li		t0, AU1000_MACEN_ADDR
	sw		zero, macen_mac0(t0)
	sw		zero, macen_mac1(t0)
	sync

	li		t0, AU1000_I2S_ADDR
	li		t1, 0x02
	sw		t1, i2s_enable(t0)

	li		t0, AU1000_UART0_ADDR
	sw		zero, uart_enable(t0)
	sync

	li		t0, AU1000_UART1_ADDR
	sw		zero, uart_enable(t0)
	sync

	li		t0, AU1000_UART2_ADDR
	sw		zero, uart_enable(t0)
	sync

	li		t0, AU1000_UART3_ADDR
	sw		zero, uart_enable(t0)
	sync

	li		t0, AU1000_SSI0_ADDR
	li		t1, 0x02
	sw		t1, ssi_enable(t0)
	sync

	li		t0, AU1000_SSI1_ADDR
	li		t1, 0x02
	sw		t1, ssi_enable(t0)
	sync

	/*
	 * Step 16) Determine cause of reset
	 */
	/* wait 10mS to debounce external signals */
	li		t1, MEM_1MS*10
1:	add		t1, -1
	bne		t1, zero, 1b
	nop

	li		t0, AU1000_SYS_ADDR
	lw		t1, sys_wakesrc(t0)

	/* Clear sys_wakemsk to prevent false events */
	sw		zero, sys_wakemsk(t0)
	sync

	/* Clear sys_wakesrc */
	//sw		zero, sys_wakesrc(t0)
	sync

	/* Check for Hardware Reset */
	andi	t2, t1, 0x01
	bne		zero, t2, hardwarereset

	/* Check for Sleep Wakeup */
	andi	t2, t1, 0x02
	bne		zero, t2, sleepwakeup
	nop

	/* Assume run-time reset */
	beq		zero, zero, runtimereset
	nop

/********************************************************************/

hardwarereset:

	/*
	 * Step 1) Initialize SDRAM
	 */
	bal		initSDRAM
	nop

	/*
	 * Step 2) Initialize BOARD-specific items
	 */
	bal		initBOARD
	nop

	/*
	 * Step 3) Invoke application
	 */
	beq		zero, zero, alldone
	nop


/********************************************************************/

runtimereset:

	/*
	 * Step 1) Initialize SDRAM
	 */
	bal		initSDRAM
	nop

	/*
	 * Step 2) Initialize BOARD-specific items
	 */
	bal		initBOARD
	nop

	/*
	 * Step 3) Invoke application
	 */
	beq		zero, zero, alldone
	nop


	
/********************************************************************/

sleepwakeup:

	/*
	 * Step 1) Initialize SDRAM. The SDRAM must be in self-refresh mode.
	 */
	bal		wakeupSDRAM
	nop

	/*
	 * Step 2) Initialize BOARD-specific items
	 */
	bal		initBOARD
	nop

	/*
	 * Step 3) Invoke application
	 */
	la		t0, AU1000_SYS_ADDR
	lw		sp, sys_scratch0(t0)
	lw		ra, sys_scratch1(t0)

	jr		ra
	nop

/********************************************************************/

	/*
	 * This routine initializes the SDRAM controller from Initial
	 * Power-up Reset or Running Reset.
	 */
initSDRAM:

	/* Only perform SDRAM init if running from ROM/Flash */
	addu	t2, ra, zero	/* preserve ra */
    bal		getPC
    nop
getPC:
    lui		t0, 0x1F00      /* ROM/flash address? */
    and		t1, t0, ra
	addu	ra, t2, zero	/* restore ra */
    bne		t0, t1, initSDRAMdone
    nop

	/* wait 1mS before setup */
	li		t1, MEM_1MS
1:	add		t1, -1
	bne		t1, zero, 1b
	nop

	li		t0, AU1000_MEM_ADDR
	li		t1, MEM_SDMODE0
	sw		t1, mem_sdmode0(t0)

	li		t1, MEM_SDMODE1
	sw		t1, mem_sdmode1(t0)

	li		t1, MEM_SDMODE2
	sw		t1, mem_sdmode2(t0)
	
	li		t1, MEM_SDADDR0
	sw		t1, mem_sdaddr0(t0)

	li		t1, MEM_SDADDR1
	sw		t1, mem_sdaddr1(t0)

	li		t1, MEM_SDADDR2
	sw		t1, mem_sdaddr2(t0)

	sync

	li		t1, MEM_SDREFCFG_D
	sw		t1, mem_sdrefcfg(t0)
	sync

	sw		zero, mem_sdprecmd(t0)
	sync

	sw		zero, mem_sdautoref(t0)
	sync

	sw		zero, mem_sdautoref(t0)
	sync

	li		t1, MEM_SDREFCFG_E
	sw		t1, mem_sdrefcfg(t0)
	sync

	li		t1, MEM_SDWRMD0
	sw		t1, mem_sdwrmd0(t0)		
	sync

	li		t1, MEM_SDWRMD1
	sw		t1, mem_sdwrmd1(t0)		
	sync

	li		t1, MEM_SDWRMD2
	sw		t1, mem_sdwrmd2(t0)
	sync

	/* wait 1mS after setup */
	li		t1, MEM_1MS
1:	add		t1, -1
	bne		t1, zero, 1b
	nop

initSDRAMdone:
	jr		ra
	nop

/********************************************************************/

wakeupSDRAM:

	/*
	 * SDRAM must be in sleep/self refresh mode. For these SDRAMs,
	 * must assert CKE, then tRC (70ns) of NOPs, then burst refresh
	 * of all rows prior to using.
	 */
	li		t0, AU1000_MEM_ADDR

	/*
	 * Enable SDRAM, assert CKE
	 */
	li		t1, MEM_SDMODE0
	sw		t1, mem_sdmode0(t0)

	li		t1, MEM_SDMODE1
	sw		t1, mem_sdmode1(t0)

	li		t1, MEM_SDMODE2
	sw		t1, mem_sdmode2(t0)
	
	li		t1, MEM_SDADDR0
	sw		t1, mem_sdaddr0(t0)

	li		t1, MEM_SDADDR1
	sw		t1, mem_sdaddr1(t0)

	li		t1, MEM_SDADDR2
	sw		t1, mem_sdaddr2(t0)

	/*
	 * Issue 70ns of NOPs (one Flash access is ~120ns)
	 * Must use non-cached KSEG1 address of Flash
	 */
	li		t1, 0xBFC00000
	lw		t1, 0(t1)
	sync
	
	/*
	 * Perform burst refresh of 4096 rows
	 */
	li		t1, 4096
burstrefresh:
	sw		zero, mem_sdautoref(t0)
	bne		zero, t1, burstrefresh
	addi	t1, t1, -1

	/*
	 * Re-start auto refresh timer
	 */
	li		t1, MEM_SDREFCFG_E
	sw		t1, mem_sdrefcfg(t0)
	sync

	jr		ra
	nop

/********************************************************************/
	
initBOARD:

	/*
	 * External and/or board-specific peripheral initialization
	 */
#define DB1000_BCSR_ADDR 0xAE000000

	/*
	 * Establish MUXed pin functionality
	 *
	 *  CS=0
	 * USB=1 USBH
	 *  U3=0 UART3
	 *  U2=1 GPIO22
	 *  U1=1 GPIO21
	 * SRC=0 GPIO6
	 * EX1=0 GPIO3
	 * EX0=0 GPIO2
	 * IRF=0 GPIO15
	 * UR3=1 UART3
	 * I2D=0 GPIO8
	 * I2S=1 GPIO31:29
	 * NI2=0 MAC1
	 *  U0=0 UART0
	 * IRD=0 IRTXD
	 * A97=0 AC97
	 *  S0=1 GPIO18:16
	 */
	li		t0, AU1000_SYS_ADDR
	li		t1,(1<<15)|(1<<13)|(1<<12)|(1<<7)|(1<<5)|(1<<0)
	sw		t1, sys_pinfunc(t0)

	/*
	 * Establish GPIO direction
	 *
	 * GPIO0 Input PCMCIA Card 0 Fully inserted
	 * GPIO1 Input PCMCIA Card 0 STSCHG#
	 * GPIO2 Input PCMCIA Card 0 IRQ#
	 * GPIO3 Input PCMCIA Card 1 Fully inserted
	 * GPIO4 Input PCMCIA Card 1 STSCHG#
	 * GPIO5 Input PCMCIA Card 1 IRQ#
	 * GPIO6 Input GPIO6_Switch S2
	 * GPIO7 Input FLASH_BUSY
	 * GPIO8 Input Daughtercard IRQ#
	 * GPIO9  UART3
	 * GPIO10 UART3
	 * GPIO11 UART3
	 * GPIO12 UART3
	 * GPIO13 UART3
	 * GPIO14 UART3
	 * GPIO15 Output Red LED#
	 * GPIO16 Output Green LED#
	 * GPIO17 Input GPIO17_Switch S4
	 * GPIO18 Input User defined
	 * GPIO19 IRDA
	 * GPIO20 UART0
	 * GPIO21 Input 2-wire (not setup here)
	 * GPIO22 Input 2-wire (not setup here)
	 * GPIO23 UART3
	 * GPIO24 MAC1
	 * GPIO25 MAC1
	 * GPIO26 MAC1
	 * GPIO27 MAC1
	 * GPIO28 MAC1
	 * GPIO29 Input
	 * GPIO30 Input
	 * GPIO31 Input
	 */
	li		t1, 0xE06601FF
	sw		t1, sys_trioutclr(t0)
	sync
	li		t1, 0x00018000
	sw		t1, sys_outputclr(t0)
	sync

	/*
	 * Establish CLOCKing
	 *
	 * FREQ5: unused
	 * FREQ4: unused
	 * FREQ3: unused
	 * FREQ2: USBH, USBD, IrDA (48MHz from AUXPLL)
	 * FREQ1: unused
	 * FREQ0: unused
	 */
	li		t0, AU1000_SYS_ADDR
	li		t1, (0<<22)|(1<<21)|(1<<20)
	sw		t1, sys_freqctrl0(t0)
	li		t1, (4<<12)|(0<<11)|(0<<10)|(4<<7)|(0<<6)|(0<<5)|(4<<2)|(0<<1)|(0<<0)
	sw		t1, sys_clksrc(t0)
	sync

	/* Take AMD PHYs out of reset */
	li		t0, DB1000_BCSR_ADDR
	li		t1, 3
	sw		t1, 0x0C(t0)

	/* Ensure PCMCIA interface disabled */
	li		t0, DB1000_BCSR_ADDR
	sw		zero, 0x10(t0)

	sync
	jr		ra
	nop
	

/********************************************************************/

alldone:
	/*
	 * Prepare to invoke application main()
	 */
	.set reorder

/********************************************************************/