comp.c

基于TI公司Cortex-M3的uart超级通信开发

//*****************************************************************************
//
// comp.c - Driver for the analog comparator.
//
// Copyright (c) 2005-2009 Luminary Micro, Inc.  All rights reserved.
// Software License Agreement
// 
// Luminary Micro, Inc. (LMI) is supplying this software for use solely and
// exclusively on LMI's microcontroller products.
// 
// The software is owned by LMI and/or its suppliers, and is protected under
// applicable copyright laws.  All rights are reserved.  You may not combine
// this software with "viral" open-source software in order to form a larger
// program.  Any use in violation of the foregoing restrictions may subject
// the user to criminal sanctions under applicable laws, as well as to civil
// liability for the breach of the terms and conditions of this license.
// 
// THIS SOFTWARE IS PROVIDED "AS IS".  NO WARRANTIES, WHETHER EXPRESS, IMPLIED
// OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF
// MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE.
// LMI SHALL NOT, IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR
// CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER.
// 
// This is part of revision 5228 of the Stellaris Peripheral Driver Library.
//
//*****************************************************************************

//*****************************************************************************
//
//! \addtogroup comp_api
//! @{
//
//*****************************************************************************

#include "inc/hw_comp.h"
#include "inc/hw_ints.h"
#include "inc/hw_memmap.h"
#include "inc/hw_types.h"
#include "driverlib/comp.h"
#include "driverlib/debug.h"
#include "driverlib/interrupt.h"

//*****************************************************************************
//
//! Configures a comparator.
//!
//! \param ulBase is the base address of the comparator module.
//! \param ulComp is the index of the comparator to configure.
//! \param ulConfig is the configuration of the comparator.
//!
//! This function will configure a comparator.  The \e ulConfig parameter is
//! the result of a logical OR operation between the \b COMP_TRIG_xxx,
//! \b COMP_INT_xxx, \b COMP_ASRCP_xxx, and \b COMP_OUTPUT_xxx values.
//!
//! The \b COMP_TRIG_xxx term can take on the following values:
//!
//! - \b COMP_TRIG_NONE to have no trigger to the ADC.
//! - \b COMP_TRIG_HIGH to trigger the ADC when the comparator output is high.
//! - \b COMP_TRIG_LOW to trigger the ADC when the comparator output is low.
//! - \b COMP_TRIG_FALL to trigger the ADC when the comparator output goes low.
//! - \b COMP_TRIG_RISE to trigger the ADC when the comparator output goes
//! high.
//! - \b COMP_TRIG_BOTH to trigger the ADC when the comparator output goes low
//! or high.
//!
//! The \b COMP_INT_xxx term can take on the following values:
//!
//! - \b COMP_INT_HIGH to generate an interrupt when the comparator output is
//! high.
//! - \b COMP_INT_LOW to generate an interrupt when the comparator output is
//! low.
//! - \b COMP_INT_FALL to generate an interrupt when the comparator output goes
//! low.
//! - \b COMP_INT_RISE to generate an interrupt when the comparator output goes
//! high.
//! - \b COMP_INT_BOTH to generate an interrupt when the comparator output goes
//! low or high.
//!
//! The \b COMP_ASRCP_xxx term can take on the following values:
//!
//! - \b COMP_ASRCP_PIN to use the dedicated Comp+ pin as the reference
//! voltage.
//! - \b COMP_ASRCP_PIN0 to use the Comp0+ pin as the reference voltage (this
//! the same as \b COMP_ASRCP_PIN for the comparator 0).
//! - \b COMP_ASRCP_REF to use the internally generated voltage as the
//! reference voltage.
//!
//! The \b COMP_OUTPUT_xxx term can take on the following values:
//!
//! - \b COMP_OUTPUT_NORMAL to enable a non-inverted output from the comparator
//! to a device pin.
//! - \b COMP_OUTPUT_INVERT to enable an inverted output from the comparator to
//! a device pin.
//! - \b COMP_OUTPUT_NONE is deprecated and behaves the same as
//! \b COMP_OUTPUT_NORMAL.
//!
//! \return None.
//
//*****************************************************************************
void
ComparatorConfigure(unsigned long ulBase, unsigned long ulComp,
                    unsigned long ulConfig)
{
    //
    // Check the arguments.
    //
    ASSERT(ulBase == COMP_BASE);
    ASSERT(ulComp < 3);

    //
    // Configure this comparator.
    //
    HWREG(ulBase + (ulComp * 0x20) + COMP_O_ACCTL0) = ulConfig;
}

//*****************************************************************************
//
//! Sets the internal reference voltage.
//!
//! \param ulBase is the base address of the comparator module.
//! \param ulRef is the desired reference voltage.
//!
//! This function will set the internal reference voltage value.  The voltage
//! is specified as one of the following values:
//!
//! - \b COMP_REF_OFF to turn off the reference voltage
//! - \b COMP_REF_0V to set the reference voltage to 0 V
//! - \b COMP_REF_0_1375V to set the reference voltage to 0.1375 V
//! - \b COMP_REF_0_275V to set the reference voltage to 0.275 V
//! - \b COMP_REF_0_4125V to set the reference voltage to 0.4125 V
//! - \b COMP_REF_0_55V to set the reference voltage to 0.55 V
//! - \b COMP_REF_0_6875V to set the reference voltage to 0.6875 V
//! - \b COMP_REF_0_825V to set the reference voltage to 0.825 V
//! - \b COMP_REF_0_928125V to set the reference voltage to 0.928125 V
//! - \b COMP_REF_0_9625V to set the reference voltage to 0.9625 V
//! - \b COMP_REF_1_03125V to set the reference voltage to 1.03125 V
//! - \b COMP_REF_1_134375V to set the reference voltage to 1.134375 V
//! - \b COMP_REF_1_1V to set the reference voltage to 1.1 V
//! - \b COMP_REF_1_2375V to set the reference voltage to 1.2375 V
//! - \b COMP_REF_1_340625V to set the reference voltage to 1.340625 V
//! - \b COMP_REF_1_375V to set the reference voltage to 1.375 V
//! - \b COMP_REF_1_44375V to set the reference voltage to 1.44375 V
//! - \b COMP_REF_1_5125V to set the reference voltage to 1.5125 V
//! - \b COMP_REF_1_546875V to set the reference voltage to 1.546875 V
//! - \b COMP_REF_1_65V to set the reference voltage to 1.65 V
//! - \b COMP_REF_1_753125V to set the reference voltage to 1.753125 V
//! - \b COMP_REF_1_7875V to set the reference voltage to 1.7875 V
//! - \b COMP_REF_1_85625V to set the reference voltage to 1.85625 V
//! - \b COMP_REF_1_925V to set the reference voltage to 1.925 V
//! - \b COMP_REF_1_959375V to set the reference voltage to 1.959375 V
//! - \b COMP_REF_2_0625V to set the reference voltage to 2.0625 V
//! - \b COMP_REF_2_165625V to set the reference voltage to 2.165625 V
//! - \b COMP_REF_2_26875V to set the reference voltage to 2.26875 V
//! - \b COMP_REF_2_371875V to set the reference voltage to 2.371875 V
//!
//! \return None.
//
//*****************************************************************************
void
ComparatorRefSet(unsigned long ulBase, unsigned long ulRef)
{
    //
    // Check the arguments.
    //
    ASSERT(ulBase == COMP_BASE);

    //
    // Set the voltage reference voltage as requested.
    //
    HWREG(ulBase + COMP_O_ACREFCTL) = ulRef;
}

//*****************************************************************************
//
//! Gets the current comparator output value.
//!
//! \param ulBase is the base address of the comparator module.
//! \param ulComp is the index of the comparator.
//!
//! This function retrieves the current value of the comparator output.
//!
//! \return Returns \b true if the comparator output is high and \b false if
//! the comparator output is low.
//
//*****************************************************************************
tBoolean
ComparatorValueGet(unsigned long ulBase, unsigned long ulComp)
{
    //
    // Check the arguments.
    //
    ASSERT(ulBase == COMP_BASE);
    ASSERT(ulComp < 3);

    //
    // Return the appropriate value based on the comparator's present output
    // value.
    //
    if(HWREG(ulBase + (ulComp * 0x20) + COMP_O_ACSTAT0) & COMP_ACSTAT0_OVAL)
    {
        return(true);
    }
    else
    {
        return(false);
    }
}

//*****************************************************************************
//
//! Registers an interrupt handler for the comparator interrupt.
//!
//! \param ulBase is the base address of the comparator module.
//! \param ulComp is the index of the comparator.
//! \param pfnHandler is a pointer to the function to be called when the
//! comparator interrupt occurs.
//!
//! This sets the handler to be called when the comparator interrupt occurs.
//! This will enable the interrupt in the interrupt controller; it is the
//! interrupt-handler's responsibility to clear the interrupt source via