stm32f10x_adc.c

stm32 红外万年历

  assert_param(IS_FUNCTIONAL_STATE(NewState));
  if (NewState != DISABLE)
  {
    /* Enable the selected ADC DMA request */
    ADCx->CR2 |= CR2_DMA_Set;
  }
  else
  {
    /* Disable the selected ADC DMA request */
    ADCx->CR2 &= CR2_DMA_Reset;
  }
}

/**
  * @brief  Enables or disables the specified ADC interrupts.
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @param  ADC_IT: specifies the ADC interrupt sources to be enabled or disabled. 
  *   This parameter can be any combination of the following values:
  *     @arg ADC_IT_EOC: End of conversion interrupt mask
  *     @arg ADC_IT_AWD: Analog watchdog interrupt mask
  *     @arg ADC_IT_JEOC: End of injected conversion interrupt mask
  * @param  NewState: new state of the specified ADC interrupts.
  *   This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void ADC_ITConfig(ADC_TypeDef* ADCx, uint16_t ADC_IT, FunctionalState NewState)
{
  uint8_t itmask = 0;
  /* Check the parameters */
  assert_param(IS_ADC_ALL_PERIPH(ADCx));
  assert_param(IS_FUNCTIONAL_STATE(NewState));
  assert_param(IS_ADC_IT(ADC_IT));
  /* Get the ADC IT index */
  itmask = (uint8_t)ADC_IT;
  if (NewState != DISABLE)
  {
    /* Enable the selected ADC interrupts */
    ADCx->CR1 |= itmask;
  }
  else
  {
    /* Disable the selected ADC interrupts */
    ADCx->CR1 &= (~(uint32_t)itmask);
  }
}

/**
  * @brief  Resets the selected ADC calibration registers.
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @retval None
  */
void ADC_ResetCalibration(ADC_TypeDef* ADCx)
{
  /* Check the parameters */
  assert_param(IS_ADC_ALL_PERIPH(ADCx));
  /* Resets the selected ADC calibration registers */  
  ADCx->CR2 |= CR2_RSTCAL_Set;
}

/**
  * @brief  Gets the selected ADC reset calibration registers status.
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @retval The new state of ADC reset calibration registers (SET or RESET).
  */
FlagStatus ADC_GetResetCalibrationStatus(ADC_TypeDef* ADCx)
{
  FlagStatus bitstatus = RESET;
  /* Check the parameters */
  assert_param(IS_ADC_ALL_PERIPH(ADCx));
  /* Check the status of RSTCAL bit */
  if ((ADCx->CR2 & CR2_RSTCAL_Set) != (uint32_t)RESET)
  {
    /* RSTCAL bit is set */
    bitstatus = SET;
  }
  else
  {
    /* RSTCAL bit is reset */
    bitstatus = RESET;
  }
  /* Return the RSTCAL bit status */
  return  bitstatus;
}

/**
  * @brief  Starts the selected ADC calibration process.
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @retval None
  */
void ADC_StartCalibration(ADC_TypeDef* ADCx)
{
  /* Check the parameters */
  assert_param(IS_ADC_ALL_PERIPH(ADCx));
  /* Enable the selected ADC calibration process */  
  ADCx->CR2 |= CR2_CAL_Set;
}

/**
  * @brief  Gets the selected ADC calibration status.
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @retval The new state of ADC calibration (SET or RESET).
  */
FlagStatus ADC_GetCalibrationStatus(ADC_TypeDef* ADCx)
{
  FlagStatus bitstatus = RESET;
  /* Check the parameters */
  assert_param(IS_ADC_ALL_PERIPH(ADCx));
  /* Check the status of CAL bit */
  if ((ADCx->CR2 & CR2_CAL_Set) != (uint32_t)RESET)
  {
    /* CAL bit is set: calibration on going */
    bitstatus = SET;
  }
  else
  {
    /* CAL bit is reset: end of calibration */
    bitstatus = RESET;
  }
  /* Return the CAL bit status */
  return  bitstatus;
}

/**
  * @brief  Enables or disables the selected ADC software start conversion .
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @param  NewState: new state of the selected ADC software start conversion.
  *   This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void ADC_SoftwareStartConvCmd(ADC_TypeDef* ADCx, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_ADC_ALL_PERIPH(ADCx));
  assert_param(IS_FUNCTIONAL_STATE(NewState));
  if (NewState != DISABLE)
  {
    /* Enable the selected ADC conversion on external event and start the selected
       ADC conversion */
    ADCx->CR2 |= CR2_EXTTRIG_SWSTART_Set;
  }
  else
  {
    /* Disable the selected ADC conversion on external event and stop the selected
       ADC conversion */
    ADCx->CR2 &= CR2_EXTTRIG_SWSTART_Reset;
  }
}

/**
  * @brief  Gets the selected ADC Software start conversion Status.
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @retval The new state of ADC software start conversion (SET or RESET).
  */
FlagStatus ADC_GetSoftwareStartConvStatus(ADC_TypeDef* ADCx)
{
  FlagStatus bitstatus = RESET;
  /* Check the parameters */
  assert_param(IS_ADC_ALL_PERIPH(ADCx));
  /* Check the status of SWSTART bit */
  if ((ADCx->CR2 & CR2_SWSTART_Set) != (uint32_t)RESET)
  {
    /* SWSTART bit is set */
    bitstatus = SET;
  }
  else
  {
    /* SWSTART bit is reset */
    bitstatus = RESET;
  }
  /* Return the SWSTART bit status */
  return  bitstatus;
}

/**
  * @brief  Configures the discontinuous mode for the selected ADC regular
  *         group channel.
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @param  Number: specifies the discontinuous mode regular channel
  *         count value. This number must be between 1 and 8.
  * @retval None
  */
void ADC_DiscModeChannelCountConfig(ADC_TypeDef* ADCx, uint8_t Number)
{
  uint32_t tmpreg1 = 0;
  uint32_t tmpreg2 = 0;
  /* Check the parameters */
  assert_param(IS_ADC_ALL_PERIPH(ADCx));
  assert_param(IS_ADC_REGULAR_DISC_NUMBER(Number));
  /* Get the old register value */
  tmpreg1 = ADCx->CR1;
  /* Clear the old discontinuous mode channel count */
  tmpreg1 &= CR1_DISCNUM_Reset;
  /* Set the discontinuous mode channel count */
  tmpreg2 = Number - 1;
  tmpreg1 |= tmpreg2 << 13;
  /* Store the new register value */
  ADCx->CR1 = tmpreg1;
}

/**
  * @brief  Enables or disables the discontinuous mode on regular group
  *         channel for the specified ADC
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @param  NewState: new state of the selected ADC discontinuous mode
  *         on regular group channel.
  *         This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void ADC_DiscModeCmd(ADC_TypeDef* ADCx, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_ADC_ALL_PERIPH(ADCx));
  assert_param(IS_FUNCTIONAL_STATE(NewState));
  if (NewState != DISABLE)
  {
    /* Enable the selected ADC regular discontinuous mode */
    ADCx->CR1 |= CR1_DISCEN_Set;
  }
  else
  {
    /* Disable the selected ADC regular discontinuous mode */
    ADCx->CR1 &= CR1_DISCEN_Reset;
  }
}

/**
  * @brief  Configures for the selected ADC regular channel its corresponding
  *         rank in the sequencer and its sample time.
  * @param  ADCx: where x can be 1, 2 or 3 to select the ADC peripheral.
  * @param  ADC_Channel: the ADC channel to configure. 
  *   This parameter can be one of the following values:
  *     @arg ADC_Channel_0: ADC Channel0 selected
  *     @arg ADC_Channel_1: ADC Channel1 selected
  *     @arg ADC_Channel_2: ADC Channel2 selected
  *     @arg ADC_Channel_3: ADC Channel3 selected
  *     @arg ADC_Channel_4: ADC Channel4 selected
  *     @arg ADC_Channel_5: ADC Channel5 selected
  *     @arg ADC_Channel_6: ADC Channel6 selected
  *     @arg ADC_Channel_7: ADC Channel7 selected
  *     @arg ADC_Channel_8: ADC Channel8 selected
  *     @arg ADC_Channel_9: ADC Channel9 selected
  *     @arg ADC_Channel_10: ADC Channel10 selected
  *     @arg ADC_Channel_11: ADC Channel11 selected
  *     @arg ADC_Channel_12: ADC Channel12 selected
  *     @arg ADC_Channel_13: ADC Channel13 selected
  *     @arg ADC_Channel_14: ADC Channel14 selected
  *     @arg ADC_Channel_15: ADC Channel15 selected
  *     @arg ADC_Channel_16: ADC Channel16 selected
  *     @arg ADC_Channel_17: ADC Channel17 selected
  * @param  Rank: The rank in the regular group sequencer. This parameter must be between 1 to 16.
  * @param  ADC_SampleTime: The sample time value to be set for the selected channel. 
  *   This parameter can be one of the following values:
  *     @arg ADC_SampleTime_1Cycles5: Sample time equal to 1.5 cycles
  *     @arg ADC_SampleTime_7Cycles5: Sample time equal to 7.5 cycles
  *     @arg ADC_SampleTime_13Cycles5: Sample time equal to 13.5 cycles
  *     @arg ADC_SampleTime_28Cycles5: Sample time equal to 28.5 cycles	
  *     @arg ADC_SampleTime_41Cycles5: Sample time equal to 41.5 cycles	
  *     @arg ADC_SampleTime_55Cycles5: Sample time equal to 55.5 cycles	
  *     @arg ADC_SampleTime_71Cycles5: Sample time equal to 71.5 cycles	
  *     @arg ADC_SampleTime_239Cycles5: Sample time equal to 239.5 cycles	
  * @retval None
  */
void ADC_RegularChannelConfig(ADC_TypeDef* ADCx, uint8_t ADC_Channel, uint8_t Rank, uint8_t ADC_SampleTime)
{
  uint32_t tmpreg1 = 0, tmpreg2 = 0;
  /* Check the parameters */
  assert_param(IS_ADC_ALL_PERIPH(ADCx));
  assert_param(IS_ADC_CHANNEL(ADC_Channel));
  assert_param(IS_ADC_REGULAR_RANK(Rank));
  assert_param(IS_ADC_SAMPLE_TIME(ADC_SampleTime));
  /* if ADC_Channel_10 ... ADC_Channel_17 is selected */
  if (ADC_Channel > ADC_Channel_9)
  {
    /* Get the old register value */
    tmpreg1 = ADCx->SMPR1;
    /* Calculate the mask to clear */
    tmpreg2 = SMPR1_SMP_Set << (3 * (ADC_Channel - 10));
    /* Clear the old channel sample time */
    tmpreg1 &= ~tmpreg2;
    /* Calculate the mask to set */
    tmpreg2 = (uint32_t)ADC_SampleTime << (3 * (ADC_Channel - 10));
    /* Set the new channel sample time */
    tmpreg1 |= tmpreg2;
    /* Store the new register value */
    ADCx->SMPR1 = tmpreg1;
  }
  else /* ADC_Channel include in ADC_Channel_[0..9] */
  {
    /* Get the old register value */
    tmpreg1 = ADCx->SMPR2;
    /* Calculate the mask to clear */
    tmpreg2 = SMPR2_SMP_Set << (3 * ADC_Channel);
    /* Clear the old channel sample time */
    tmpreg1 &= ~tmpreg2;
    /* Calculate the mask to set */
    tmpreg2 = (uint32_t)ADC_SampleTime << (3 * ADC_Channel);
    /* Set the new channel sample time */
    tmpreg1 |= tmpreg2;
    /* Store the new register value */
    ADCx->SMPR2 = tmpreg1;
  }
  /* For Rank 1 to 6 */
  if (Rank < 7)
  {
    /* Get the old register value */
    tmpreg1 = ADCx->SQR3;
    /* Calculate the mask to clear */
    tmpreg2 = SQR3_SQ_Set << (5 * (Rank - 1));
    /* Clear the old SQx bits for the selected rank */
    tmpreg1 &= ~tmpreg2;
    /* Calculate the mask to set */
    tmpreg2 = (uint32_t)ADC_Channel << (5 * (Rank - 1));
    /* Set the SQx bits for the selected rank */
    tmpreg1 |= tmpreg2;
    /* Store the new register value */
    ADCx->SQR3 = tmpreg1;
  }
  /* For Rank 7 to 12 */
  else if (Rank < 13)
  {
    /* Get the old register value */
    tmpreg1 = ADCx->SQR2;
    /* Calculate the mask to clear */
    tmpreg2 = SQR2_SQ_Set << (5 * (Rank - 7));
    /* Clear the old SQx bits for the selected rank */
    tmpreg1 &= ~tmpreg2;
    /* Calculate the mask to set */