diskio.c

stm32 红外万年历

#include "mmc_sd.h"
#include "diskio.h"
#include "flash.h"
#include  <stdio.h>	 
//////////////////////////////////////////////////////////////////////////////////	 
//本程序只供学习使用，未经作者许可，不得用于其它任何用途
//Mini STM32开发板
//FATFS Diskio 驱动代码		   
//正点原子@ALIENTEK
//技术论坛:www.openedv.com
//创建日期:2011/5/13 
//版本：V2.0
//版权所有，盗版必究。
//Copyright(C) 正点原子 2009-2019
//All rights reserved
//********************************************************************************

#define SD_CARD	 0  //SD卡,卷标为0
#define EX_FLASH 1	//外部flash,卷标为1

#define FLASH_SECTOR_SIZE 	512
//前2M字节给fatfs用,后2M字节~2M+500K给用户用,2M+500K以后,用于存放字库,字库占用1.5M.
#define FLASH_SECTOR_COUNT 	4096  //全部一起,总共有8192个扇区(以512字节算) W25Q16为2048,Q32为4096,Q64为16384 这里强制用512字节
#define FLASH_BLOCK_SIZE  	8     //每个BLOCK有8个扇区

//初始化磁盘
DSTATUS disk_initialize (
	BYTE drv				/* Physical drive nmuber (0..) */
)
{	
	u8 res;	    
	switch(drv)
	{
		case SD_CARD://SD卡
			res = SD_Initialize();//SD_Initialize();
			break;
		case EX_FLASH://外部flash
			SPI_Flash_Init();
			if(SPI_Flash_ReadID()!=SPI_FLASH_TYPE)res=1;//W25Q16 ID=0XEF15
			else res=0;
			break;
		default:
			res=1; 
	}		 
	if(res)return  STA_NOINIT;
	else return 0; //初始化成功
}   
//获得磁盘状态
DSTATUS disk_status (
	BYTE drv		/* Physical drive nmuber (0..) */
)
{		   
    return 0;
}
 //读扇区
 //drv:磁盘编号0~9
 //*buff:数据接收缓冲首地址
 //sector:扇区地址
 //count:需要读取的扇区数
DRESULT disk_read (
	BYTE drv,		/* Physical drive nmuber (0..) */
	BYTE *buff,		/* Data buffer to store read data */
	DWORD sector,	/* Sector address (LBA) */
	BYTE count		/* Number of sectors to read (1..255) */
)
{
	u8 res=0; 
    if (!count)return RES_PARERR;//count不能等于0，否则返回参数错误		 	 
	switch(drv)
	{
		case SD_CARD://SD卡
			res=SD_ReadDisk(buff,sector,count);
			break;
		case EX_FLASH://外部flash
			for(;count>0;count--)
			{
				SPI_Flash_Read(buff,sector*FLASH_SECTOR_SIZE,FLASH_SECTOR_SIZE);
				sector++;
				buff+=FLASH_SECTOR_SIZE;
			}
			res=0;
			break;
		default:
			res=1; 
	}
    //处理返回值，将SPI_SD_driver.c的返回值转成ff.c的返回值
    if(res == 0x00)return RES_OK;	 
    else return RES_ERROR;	   
}  
 //写扇区
 //drv:磁盘编号0~9
 //*buff:发送数据首地址
 //sector:扇区地址
 //count:需要写入的扇区数	    
#if _READONLY == 0
DRESULT disk_write (
	BYTE drv,			/* Physical drive nmuber (0..) */
	const BYTE *buff,	        /* Data to be written */
	DWORD sector,		/* Sector address (LBA) */
	BYTE count			/* Number of sectors to write (1..255) */
)
{
	u8 res=0;  
    if (!count)return RES_PARERR;//count不能等于0，否则返回参数错误		 	 
	switch(drv)
	{
		case SD_CARD://SD卡
			res=SD_WriteDisk((u8*)buff,sector,count);
			break;
		case EX_FLASH://外部flash
			for(;count>0;count--)
			{
				//SPI_Flash_Erase_Sector(sector);
				SPI_Flash_Write((u8*)buff,sector*FLASH_SECTOR_SIZE,FLASH_SECTOR_SIZE);
				sector++;
				buff+=FLASH_SECTOR_SIZE;
			}
			res=0;
			break;
		default:
			res=1; 
	}
     //处理返回值，将SPI_SD_driver.c的返回值转成ff.c的返回值
    if(res == 0x00)return RES_OK;	 
    else return RES_ERROR;		 
}
#endif /* _READONLY */

//其他表参数的获得
 //drv:磁盘编号0~9
 //ctrl:控制代码
 //*buff:发送/接收缓冲区指针
DRESULT disk_ioctl (
	BYTE drv,		/* Physical drive nmuber (0..) */
	BYTE ctrl,		/* Control code */
	void *buff		/* Buffer to send/receive control data */
)
{	
	DRESULT res;						  
	if(drv==SD_CARD)//SD卡
	{
	    switch(ctrl)
	    {
		    case CTRL_SYNC:
				SD_CS=0;
		        if(SD_WaitReady()==0)res = RES_OK; 
		        else res = RES_ERROR;	  
				SD_CS=1;
		        break;	 
		    case GET_SECTOR_SIZE:
		        *(WORD*)buff = 512;
		        res = RES_OK;
		        break;	 
		    case GET_BLOCK_SIZE:
		        *(WORD*)buff = 8;
		        res = RES_OK;
		        break;	 
		    case GET_SECTOR_COUNT:
		        *(DWORD*)buff = SD_GetSectorCount();
		        res = RES_OK;
		        break;
		    default:
		        res = RES_PARERR;
		        break;
	    }
	}else if(drv==EX_FLASH)	//外部FLASH  
	{
	    switch(ctrl)
	    {
		    case CTRL_SYNC:
				res = RES_OK; 
		        break;	 
		    case GET_SECTOR_SIZE:
		        *(WORD*)buff = FLASH_SECTOR_SIZE;
		        res = RES_OK;
		        break;	 
		    case GET_BLOCK_SIZE:
		        *(WORD*)buff = FLASH_BLOCK_SIZE;
		        res = RES_OK;
		        break;	 
		    case GET_SECTOR_COUNT:
		        *(DWORD*)buff = FLASH_SECTOR_COUNT;
		        res = RES_OK;
		        break;
		    default:
		        res = RES_PARERR;
		        break;
	    }
	}else res=RES_ERROR;//其他的不支持
    return res;
}   
//获得时间
//User defined function to give a current time to fatfs module          */
//31-25: Year(0-127 org.1980), 24-21: Month(1-12), 20-16: Day(1-31) */                                                                                                                                                                                                                                          
//15-11: Hour(0-23), 10-5: Minute(0-59), 4-0: Second(0-29 *2) */                                                                                                                                                                                                                                                
DWORD get_fattime (void)
{
	return 0;
}