msp430x24x_uscia1_spi_09.s43

来自「步进电机驱动程序msp430f247单片机」· S43 代码 · 共 106 行

;*******************************************************************************
;   MSP430x24x Demo - USCI_A1, SPI 3-Wire Master Incremented Data
;
;   Description: SPI master talks to SPI slave using 3-wire mode. Incrementing
;   data is sent by the master starting at 0x01. Received data is expected to
;   be same as the previous transmission.  USCI RX ISR is used to handle
;   communication with the CPU, normally in LPM0. If high, P1.0 indicates
;   valid data reception.
;   ACLK = n/a, MCLK = SMCLK = DCO ~1.045MHz, BRCLK = SMCLK/2 
;
;   Use with SPI Slave Data Echo code example. If slave is in debug mode, P3.6
;   slave reset signal conflicts with slave's JTAG; to work around, use IAR's
;   "Release JTAG on Go" on slave device.  If breakpoints are set in
;   slave RX ISR, master must stopped also to avoid overrunning slave
;   RXBUF.
;
;                    MSP430F249
;                 -----------------
;             /|\|              XIN|-
;              | |                 |
;              --|RST          XOUT|-
;                |                 |
;                |             P3.6|-> Data Out (UCA1SIMO)
;                |                 |
;          LED <-|P1.0         P3.7|<- Data In (UCA1SOMI)
;                |                 |
;  Slave reset <-|P3.5         P5.0|-> Serial Clock Out (UCA1CLK)
;
;   B. Nisarga
;   Texas Instruments Inc.
;   September 2007
;   Built with IAR Embedded Workbench Version: 3.42A
;*******************************************************************************
#include "msp430x24x.h"

#define     MST_Data   R6
#define     SLV_Data   R7
;-------------------------------------------------------------------------------
            RSEG    CSTACK                  ; Define stack segment
;-------------------------------------------------------------------------------
            RSEG    CODE                    ; Assemble to Flash memory
;-------------------------------------------------------------------------------
RESET       mov.w   #SFE(CSTACK),SP         ; Initialize stackpointer
StopWDT     mov.w   #WDTPW+WDTHOLD,&WDTCTL  ; Stop watchdog timer
CheckCal    cmp.b   #0FFh,&CALBC1_1MHZ      ; Calibration constants erased?
            jeq     Trap
            cmp.b   #0FFh,&CALDCO_1MHZ
            jne     Load  
Trap        jmp     $                       ; Trap CPU!!
Load        mov.b   &CALBC1_1MHZ,&BCSCTL1   ; Set DCO to 1MHz
            mov.b   &CALDCO_1MHZ,&DCOCTL    ;
SetupP1     clr.b   &P1OUT                  ; 
            bis.b   #01h,&P1DIR             ; P1 setup for LED 
SetupP3     bis.b   #020h,&P3OUT
            bis.b   #020h,&P3DIR
            bis.b   #0C0h,&P3SEL            ; P3.6,7 USCI_A1 option select
SetupP5     bis.b   #01h,&P5SEL             ; P5.0 USCI_A1 option select            
SetupSPI    bis.b   #UCCKPL+UCMSB+UCMST+UCSYNC,&UCA1CTL0;3-pin, 8-bit SPI master
            bis.b   #UCSSEL_2,&UCA1CTL1     ; SMCLK
            bis.b   #02h,&UCA1BR0           ; /2
            clr.b   &UCA1BR1                ;
            clr.b   &UCA1MCTL               ; No modulation
            bic.b   #UCSWRST,&UCA1CTL1      ; **Initialize USCI state machine**
            bis.b   #UCA1RXIE,&UC1IE        ; Enable USCI_A1 RX interrupt

            bic.b   #020h,&P3OUT            ; Now with SPI signals initialized,
            bis.b   #020h,&P3OUT            ; reset slave
            mov.w   #50,R15                 ; Wait for slave to initialize
waitForSlv  dec.w   R15                     ;
            jnz     waitForSlv              ;
                                            ;
            mov.b   #001h,MST_Data          ; Initialize data values
            mov.b   #000h,SLV_Data          ;
                                            ;
Mainloop    mov.b   MST_Data,&UCA1TXBUF     ; Transmit first character
            bis.b   #LPM0+GIE,SR            ; CPU off, enable interrupts
            nop                             ; Required for debugger only
                                            ;
;-------------------------------------------------------------------------------
USCIA1RX_ISR;       Test for valid RX and TX character
;-------------------------------------------------------------------------------
TX1         bit.b   #UCA1TXIFG,&UC1IFG      ; USCI_A1 TX buffer ready?
            jz      TX1                     ; Jump is TX buffer not ready
                                            ;
            cmp.b   SLV_Data,&UCA1RXBUF     ; Test for correct character RX'd
            jeq     Pass                    ;
Fail        bic.b   #01h,&P1OUT             ; If incorrect, clear LED
            jmp     TX2                     ;
Pass        bis.b   #01h,&P1OUT             ; If correct, light LED
TX2         inc.b   MST_Data                ; Increment master value
            inc.b   SLV_Data                ; Increment expected slave value
            mov.b   MST_Data,&UCA1TXBUF     ; Send next value
                                            ;
            mov.w   #30,R15                 ; Add time between transmissions to
cycleDelay  dec.w   R15                     ; make sure slave can keep up
            jnz     cycleDelay              ;
            reti                            ; Exit ISR
;-------------------------------------------------------------------------------
            COMMON  INTVEC                  ; Interrupt Vectors
;-------------------------------------------------------------------------------
            ORG     USCIAB1RX_VECTOR        ; USCI_A1 Rx Vector
            DW      USCIA1RX_ISR            ;
            ORG     RESET_VECTOR            ; RESET Vector
            DW      RESET                   ;
            END