msp430x24x_adc12_03.s43

来自「步进电机驱动程序msp430f247单片机」· S43 代码 · 共 89 行

;*******************************************************************************
;   MSP430x24x Demo - ADC12, Sample A10 Temp, Set P1.0 if Temp ++ ~2C
;
;   Description: Use ADC12 and the integrated temperature sensor to detect
;   temperature gradients. The temperature sensor output voltage is sampled
;   ~ every 80ms and compared with the defined delta values using an ISR.
;   (ADC12OSC/256)/ determines sample time which needs to be greater than
;   30us for temperature sensor.
;   ADC12 is operated in repeat-single channel mode with the sample and
;   convert trigger sourced from Timer_A CCR1. The ADC12MEM0_IFG at the end
;   of each conversion will trigger an ISR.
;   ACLK = 32kHz, MCLK = SMCLK = default DCO 1048576Hz, ADC12CLK = ADC12OSC
;
;               MSP430x24x
;             -----------------
;         /|\|              XIN|-
;          | |                 | 32kHz
;          --|RST          XOUT|-
;            |                 |
;            |             P1.0|-->LED
;
;
;   B. Nisarga
;   Texas Instruments Inc.
;   September 2007
;   Built with IAR Embedded Workbench Version: 3.42A
;*******************************************************************************
#include "msp430x24x.h"

ADCDeltaOn  EQU     12                      ;  ~ 2 Deg C delta for LED on

;-------------------------------------------------------------------------------
            RSEG    CSTACK                  ; Define stack segment
;-------------------------------------------------------------------------------
            RSEG    CODE                    ; Assemble to Flash memory
;-------------------------------------------------------------------------------
RESET       mov.w   #SFE(CSTACK),SP         ; Initialize stackpointer
            mov.w   #WDTPW+WDTHOLD,WDTCTL   ; Stop watchdog
            mov.w   #SHS_1+SHP+CONSEQ_2,&ADC12CTL1  ; TA trig., rpt conv
            mov.b   #SREF_1+INCH_10,&ADC12MCTL0  ; Channel A10, Vref+
            bis.w   #001h,&ADC12IE          ; Enable ADC12IFG.0
            mov.w   #SHT0_8+REF2_5V+REFON+ADC12ON,&ADC12CTL0  ; Config ADC12
            ; Delay for Ref to settle
            mov.w   #13600,&TACCR0          ; Delay to allow Ref to settle
            bis.w   #CCIE,&TACCTL0          ; Compare-mode interrupt.
            mov.w   #TACLR+MC_1+TASSEL_2,&TACTL; up mode, SMCLK
            bis.w   #LPM0+GIE,SR            ; Enter LPM0, Enable interrupts
            bic.w   #CCIE,&TACCTL0          ; Disable timer interrupt
            dint                            ; Disable Interrupts
            
            bis.w   #ENC,&ADC12CTL0         ; Config ADC12
            mov.w   #OUTMOD_4,&TACCTL1      ; Toggle on EQU1 (TAR = 0)
            mov.w   #TASSEL_2+MC_2,&TACTL   ; SMCLK, cont-mode
ADC_Wait    bit.w   #001h,&ADC12IFG         ; First conversion?
            jz      ADC_Wait
            mov.w   &ADC12MEM0,R4           ; Read out 1st ADC value
            add.w   #ADCDeltaOn,R4          ;
            clr.b   &P1OUT                  ; Clear P5
            bis.b   #BIT0,&P1DIR             ; P1.0 as output
                                            ;
Mainloop    bis.w   #LPM0+GIE,SR            ; Enter LPM0, enable interrupts
            nop                             ; Required only for debugger
                                            ;
;-------------------------------------------------------------------------------
TA0_ISR;    ISR for CCR0,  Delay for Ref to settle
;-------------------------------------------------------------------------------
            clr     &TACTL                  ; clear Timer_A control registers
            bic.w   #LPM0,0(SP)             ; Exit LPMx, interrupts enabled
            reti                            ;
;-------------------------------------------------------------------------------
ADC12_ISR;
;-------------------------------------------------------------------------------
            cmp.w   R4,&ADC12MEM0           ; ADC12MEM0 = A10 > R4
            jlo     ADC_ISR_1               ; Again
            bis.b   #BIT0,&P1OUT            ; P1.0 = 1
            reti                            ;
ADC_ISR_1   bic.b   #BIT0,&P1OUT            ; P1.0 = 0
            reti                            ;
;-------------------------------------------------------------------------------
            COMMON  INTVEC                  ; Interrupt Vectors
;-------------------------------------------------------------------------------
            ORG     TIMERA0_VECTOR          ; Timer_A0 Vector
            DW      TA0_ISR
            ORG     ADC12_VECTOR            ; ADC12 Vector
            DW      ADC12_ISR
            ORG     RESET_VECTOR            ; POR, ext. Reset
            DW      RESET
            END