📄 opt.h
字号:
#ifndef IP_OPTIONS_ALLOWED
#define IP_OPTIONS_ALLOWED 1
#endif
/**
* IP_REASSEMBLY==1: Reassemble incoming fragmented IP packets. Note that
* this option does not affect outgoing packet sizes, which can be controlled
* via IP_FRAG.
*/
#ifndef IP_REASSEMBLY
#define IP_REASSEMBLY 1
#endif
/**
* IP_FRAG==1: Fragment outgoing IP packets if their size exceeds MTU. Note
* that this option does not affect incoming packet sizes, which can be
* controlled via IP_REASSEMBLY.
*/
#ifndef IP_FRAG
#define IP_FRAG 1
#endif
/**
* IP_REASS_MAXAGE: Maximum time (in multiples of IP_TMR_INTERVAL - so seconds, normally)
* a fragmented IP packet waits for all fragments to arrive. If not all fragments arrived
* in this time, the whole packet is discarded.
*/
#ifndef IP_REASS_MAXAGE
#define IP_REASS_MAXAGE 3
#endif
/**
* IP_REASS_MAX_PBUFS: Total maximum amount of pbufs waiting to be reassembled.
* Since the received pbufs are enqueued, be sure to configure
* PBUF_POOL_SIZE > IP_REASS_MAX_PBUFS so that the stack is still able to receive
* packets even if the maximum amount of fragments is enqueued for reassembly!
*/
#ifndef IP_REASS_MAX_PBUFS
#define IP_REASS_MAX_PBUFS 10
#endif
/**
* IP_FRAG_USES_STATIC_BUF==1: Use a static MTU-sized buffer for IP
* fragmentation. Otherwise pbufs are allocated and reference the original
* packet data to be fragmented (or with LWIP_NETIF_TX_SINGLE_PBUF==1,
* new PBUF_RAM pbufs are used for fragments).
* ATTENTION: IP_FRAG_USES_STATIC_BUF==1 may not be used for DMA-enabled MACs!
*/
#ifndef IP_FRAG_USES_STATIC_BUF
#define IP_FRAG_USES_STATIC_BUF 0
#endif
/**
* IP_FRAG_MAX_MTU: Assumed max MTU on any interface for IP frag buffer
* (requires IP_FRAG_USES_STATIC_BUF==1)
*/
#if IP_FRAG_USES_STATIC_BUF && !defined(IP_FRAG_MAX_MTU)
#define IP_FRAG_MAX_MTU 1500
#endif
/**
* IP_DEFAULT_TTL: Default value for Time-To-Live used by transport layers.
*/
#ifndef IP_DEFAULT_TTL
#define IP_DEFAULT_TTL 255
#endif
/**
* IP_SOF_BROADCAST=1: Use the SOF_BROADCAST field to enable broadcast
* filter per pcb on udp and raw send operations. To enable broadcast filter
* on recv operations, you also have to set IP_SOF_BROADCAST_RECV=1.
*/
#ifndef IP_SOF_BROADCAST
#define IP_SOF_BROADCAST 0
#endif
/**
* IP_SOF_BROADCAST_RECV (requires IP_SOF_BROADCAST=1) enable the broadcast
* filter on recv operations.
*/
#ifndef IP_SOF_BROADCAST_RECV
#define IP_SOF_BROADCAST_RECV 0
#endif
/*
----------------------------------
---------- ICMP options ----------
----------------------------------
*/
/**
* LWIP_ICMP==1: Enable ICMP module inside the IP stack.
* Be careful, disable that make your product non-compliant to RFC1122
*/
#ifndef LWIP_ICMP
#define LWIP_ICMP 1
#endif
/**
* ICMP_TTL: Default value for Time-To-Live used by ICMP packets.
*/
#ifndef ICMP_TTL
#define ICMP_TTL (IP_DEFAULT_TTL)
#endif
/**
* LWIP_BROADCAST_PING==1: respond to broadcast pings (default is unicast only)
*/
#ifndef LWIP_BROADCAST_PING
#define LWIP_BROADCAST_PING 0
#endif
/**
* LWIP_MULTICAST_PING==1: respond to multicast pings (default is unicast only)
*/
#ifndef LWIP_MULTICAST_PING
#define LWIP_MULTICAST_PING 0
#endif
/*
---------------------------------
---------- RAW options ----------
---------------------------------
*/
/**
* LWIP_RAW==1: Enable application layer to hook into the IP layer itself.
*/
#ifndef LWIP_RAW
#define LWIP_RAW 1
#endif
/**
* LWIP_RAW==1: Enable application layer to hook into the IP layer itself.
*/
#ifndef RAW_TTL
#define RAW_TTL (IP_DEFAULT_TTL)
#endif
/*
----------------------------------
---------- DHCP options ----------
----------------------------------
*/
/**
* LWIP_DHCP==1: Enable DHCP module.
*/
#ifndef LWIP_DHCP
#define LWIP_DHCP 0
#endif
/**
* DHCP_DOES_ARP_CHECK==1: Do an ARP check on the offered address.
*/
#ifndef DHCP_DOES_ARP_CHECK
#define DHCP_DOES_ARP_CHECK ((LWIP_DHCP) && (LWIP_ARP))
#endif
/*
------------------------------------
---------- AUTOIP options ----------
------------------------------------
*/
/**
* LWIP_AUTOIP==1: Enable AUTOIP module.
*/
#ifndef LWIP_AUTOIP
#define LWIP_AUTOIP 0
#endif
/**
* LWIP_DHCP_AUTOIP_COOP==1: Allow DHCP and AUTOIP to be both enabled on
* the same interface at the same time.
*/
#ifndef LWIP_DHCP_AUTOIP_COOP
#define LWIP_DHCP_AUTOIP_COOP 0
#endif
/**
* LWIP_DHCP_AUTOIP_COOP_TRIES: Set to the number of DHCP DISCOVER probes
* that should be sent before falling back on AUTOIP. This can be set
* as low as 1 to get an AutoIP address very quickly, but you should
* be prepared to handle a changing IP address when DHCP overrides
* AutoIP.
*/
#ifndef LWIP_DHCP_AUTOIP_COOP_TRIES
#define LWIP_DHCP_AUTOIP_COOP_TRIES 9
#endif
/*
----------------------------------
---------- SNMP options ----------
----------------------------------
*/
/**
* LWIP_SNMP==1: Turn on SNMP module. UDP must be available for SNMP
* transport.
*/
#ifndef LWIP_SNMP
#define LWIP_SNMP 0
#endif
/**
* SNMP_CONCURRENT_REQUESTS: Number of concurrent requests the module will
* allow. At least one request buffer is required.
* Does not have to be changed unless external MIBs answer request asynchronously
*/
#ifndef SNMP_CONCURRENT_REQUESTS
#define SNMP_CONCURRENT_REQUESTS 1
#endif
/**
* SNMP_TRAP_DESTINATIONS: Number of trap destinations. At least one trap
* destination is required
*/
#ifndef SNMP_TRAP_DESTINATIONS
#define SNMP_TRAP_DESTINATIONS 1
#endif
/**
* SNMP_PRIVATE_MIB:
* When using a private MIB, you have to create a file 'private_mib.h' that contains
* a 'struct mib_array_node mib_private' which contains your MIB.
*/
#ifndef SNMP_PRIVATE_MIB
#define SNMP_PRIVATE_MIB 0
#endif
/**
* Only allow SNMP write actions that are 'safe' (e.g. disabeling netifs is not
* a safe action and disabled when SNMP_SAFE_REQUESTS = 1).
* Unsafe requests are disabled by default!
*/
#ifndef SNMP_SAFE_REQUESTS
#define SNMP_SAFE_REQUESTS 1
#endif
/**
* The maximum length of strings used. This affects the size of
* MEMP_SNMP_VALUE elements.
*/
#ifndef SNMP_MAX_OCTET_STRING_LEN
#define SNMP_MAX_OCTET_STRING_LEN 127
#endif
/**
* The maximum depth of the SNMP tree.
* With private MIBs enabled, this depends on your MIB!
* This affects the size of MEMP_SNMP_VALUE elements.
*/
#ifndef SNMP_MAX_TREE_DEPTH
#define SNMP_MAX_TREE_DEPTH 15
#endif
/**
* The size of the MEMP_SNMP_VALUE elements, normally calculated from
* SNMP_MAX_OCTET_STRING_LEN and SNMP_MAX_TREE_DEPTH.
*/
#ifndef SNMP_MAX_VALUE_SIZE
#define SNMP_MAX_VALUE_SIZE LWIP_MAX((SNMP_MAX_OCTET_STRING_LEN)+1, sizeof(s32_t)*(SNMP_MAX_TREE_DEPTH))
#endif
/*
----------------------------------
---------- IGMP options ----------
----------------------------------
*/
/**
* LWIP_IGMP==1: Turn on IGMP module.
*/
#ifndef LWIP_IGMP
#define LWIP_IGMP 0
#endif
/*
----------------------------------
---------- DNS options -----------
----------------------------------
*/
/**
* LWIP_DNS==1: Turn on DNS module. UDP must be available for DNS
* transport.
*/
#ifndef LWIP_DNS
#define LWIP_DNS 0
#endif
/** DNS maximum number of entries to maintain locally. */
#ifndef DNS_TABLE_SIZE
#define DNS_TABLE_SIZE 4
#endif
/** DNS maximum host name length supported in the name table. */
#ifndef DNS_MAX_NAME_LENGTH
#define DNS_MAX_NAME_LENGTH 256
#endif
/** The maximum of DNS servers */
#ifndef DNS_MAX_SERVERS
#define DNS_MAX_SERVERS 2
#endif
/** DNS do a name checking between the query and the response. */
#ifndef DNS_DOES_NAME_CHECK
#define DNS_DOES_NAME_CHECK 1
#endif
/** DNS message max. size. Default value is RFC compliant. */
#ifndef DNS_MSG_SIZE
#define DNS_MSG_SIZE 512
#endif
/** DNS_LOCAL_HOSTLIST: Implements a local host-to-address list. If enabled,
* you have to define
* #define DNS_LOCAL_HOSTLIST_INIT {{"host1", 0x123}, {"host2", 0x234}}
* (an array of structs name/address, where address is an u32_t in network
* byte order).
*
* Instead, you can also use an external function:
* #define DNS_LOOKUP_LOCAL_EXTERN(x) extern u32_t my_lookup_function(const char *name)
* that returns the IP address or INADDR_NONE if not found.
*/
#ifndef DNS_LOCAL_HOSTLIST
#define DNS_LOCAL_HOSTLIST 0
#endif /* DNS_LOCAL_HOSTLIST */
/** If this is turned on, the local host-list can be dynamically changed
* at runtime. */
#ifndef DNS_LOCAL_HOSTLIST_IS_DYNAMIC
#define DNS_LOCAL_HOSTLIST_IS_DYNAMIC 0
#endif /* DNS_LOCAL_HOSTLIST_IS_DYNAMIC */
/*
---------------------------------
---------- UDP options ----------
---------------------------------
*/
/**
* LWIP_UDP==1: Turn on UDP.
*/
#ifndef LWIP_UDP
#define LWIP_UDP 1
#endif
/**
* LWIP_UDPLITE==1: Turn on UDP-Lite. (Requires LWIP_UDP)
*/
#ifndef LWIP_UDPLITE
#define LWIP_UDPLITE 0
#endif
/**
* UDP_TTL: Default Time-To-Live value.
*/
#ifndef UDP_TTL
#define UDP_TTL (IP_DEFAULT_TTL)
#endif
/**
* LWIP_NETBUF_RECVINFO==1: append destination addr and port to every netbuf.
*/
#ifndef LWIP_NETBUF_RECVINFO
#define LWIP_NETBUF_RECVINFO 0
#endif
/*
---------------------------------
---------- TCP options ----------
---------------------------------
*/
/**
* LWIP_TCP==1: Turn on TCP.
*/
#ifndef LWIP_TCP
#define LWIP_TCP 1
#endif
/**
* TCP_TTL: Default Time-To-Live value.
*/
#ifndef TCP_TTL
#define TCP_TTL (IP_DEFAULT_TTL)
#endif
/**
* TCP_WND: The size of a TCP window. This must be at least
* (2 * TCP_MSS) for things to work well
*/
#ifndef TCP_WND
#define TCP_WND (4 * TCP_MSS)
#endif
/**
* TCP_MAXRTX: Maximum number of retransmissions of data segments.
*/
#ifndef TCP_MAXRTX
#define TCP_MAXRTX 12
#endif
/**
* TCP_SYNMAXRTX: Maximum number of retransmissions of SYN segments.
*/
#ifndef TCP_SYNMAXRTX
#define TCP_SYNMAXRTX 6
#endif
/**
* TCP_QUEUE_OOSEQ==1: TCP will queue segments that arrive out of order.
* Define to 0 if your device is low on memory.
*/
#ifndef TCP_QUEUE_OOSEQ
#define TCP_QUEUE_OOSEQ (LWIP_TCP)
#endif
/**
* TCP_MSS: TCP Maximum segment size. (default is 536, a conservative default,
* you might want to increase this.)
* For the receive side, this MSS is advertised to the remote side
* when opening a connection. For the transmit size, this MSS sets
* an upper limit on the MSS advertised by the remote host.
*/
#ifndef TCP_MSS
#define TCP_MSS 536
#endif
/**
* TCP_CALCULATE_EFF_SEND_MSS: "The maximum size of a segment that TCP really
* sends, the 'effective send MSS,' MUST be the smaller of the send MSS (which
* reflects the available reassembly buffer size at the remote host) and the
* largest size permitted by the IP layer" (RFC 1122)
* Setting this to 1 enables code that checks TCP_MSS against the MTU of the
* netif used for a connection and limits the MSS if it would be too big otherwise.
*/
#ifndef TCP_CALCULATE_EFF_SEND_MSS
#define TCP_CALCULATE_EFF_SEND_MSS 1
#endif
/**
* TCP_SND_BUF: TCP sender buffer space (bytes).
*/
#ifndef TCP_SND_BUF
#define TCP_SND_BUF 256
#endif
/**
* TCP_SND_QUEUELEN: TCP sender buffer space (pbufs). This must be at least
* as much as (2 * TCP_SND_BUF/TCP_MSS) for things to work.
*/
#ifndef TCP_SND_QUEUELEN
#define TCP_SND_QUEUELEN ((4 * (TCP_SND_BUF) + (TCP_MSS - 1))/(TCP_MSS))
#endif
/**
* TCP_SNDLOWAT: TCP writable space (bytes). This must be less than
* TCP_SND_BUF. It is the amount of space which must be available in the
* TCP snd_buf for select to return writable (combined with TCP_SNDQUEUELOWAT).
*/
#ifndef TCP_SNDLOWAT
#define TCP_SNDLOWAT ((TCP_SND_BUF)/2)
#endif
/**
* TCP_SNDQUEUELOWAT: TCP writable bufs (pbuf count). This must be grater
* than TCP_SND_QUEUELEN. If the number of pbufs queued on a pcb drops below
* this number, select returns writable (combined with TCP_SNDLOWAT).
*/
#ifndef TCP_SNDQUEUELOWAT
#define TCP_SNDQUEUELOWAT ((TCP_SND_QUEUELEN)/2)
#endif
/**
* TCP_LISTEN_BACKLOG: Enable the backlog option for tcp listen pcb.
*/
#ifndef TCP_LISTEN_BACKLOG
#define TCP_LISTEN_BACKLOG 0
#endif
/**
* The maximum allowed backlog for TCP listen netconns.
* This backlog is used unless another is explicitly specified.
* 0xff is the maximum (u8_t).
*/
#ifndef TCP_DEFAULT_LISTEN_BACKLOG
#define TCP_DEFAULT_LISTEN_BACKLOG 0xff
#endif
/**
* TCP_OVERSIZE: The maximum number of bytes that tcp_write may
* allocate ahead of time in an attempt to create shorter pbuf chains
* for transmission. The meaningful range is 0 to TCP_MSS. Some
* suggested values are:
*
* 0: Disable oversized allocation. Each tcp_write() allocates a new
pbuf (old behaviour).
* 1: Allocate size-aligned pbufs with minimal excess. Use this if your
* scatter-gather DMA requires aligned fragments.
* 128: Limit the pbuf/memory overhead to 20%.
* TCP_MSS: Try to create unfragmented TCP packets.
* TCP_MSS/4: Try to create 4 fragments or less per TCP packet.
*/
#ifndef TCP_OVERSIZE
#define TCP_OVERSIZE TCP_MSS
#endif
/**
* LWIP_TCP_TIMESTAMPS==1: support the TCP timestamp option.
*/
#ifndef LWIP_TCP_TIMESTAMPS
#define LWIP_TCP_TIMESTAMPS 0
#endif
/**
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -