fpga实现串口通信.txt

在ISE上可运行次程序 改程序主要用实现FPGA串口通信

FPGA实现串口通信 
0
推荐FPGA板上实现串口通信

 

    FPGA开发板上写的Verilog代码：

功能是从电脑端发送一个字节，然后把它接收回来。

 

`timescale 1ns / 10ps

`define Tgate 1

 

module uart_loop (osc,rst_,rxd,sdo,data_ready,framing_error,parity_error);

 

input osc ;

input rst_ ;

 

input rxd ;

output sdo ;

 

output data_ready ;

output framing_error ;

output parity_error ;

 

wire rst = ~rst_;

reg[7:0] oscd163r;

always @(posedge osc or posedge rst)

begin

if (rst)

oscd163r <= 0 ; 

else

oscd163r <= (oscd163r==8'HA3) ? 0 : (oscd163r + 1) ;

end

 

reg clk16x;

always @(posedge osc or posedge rst)

begin

if (rst)

clk16x <= 0 ; 

else

clk16x <= (oscd163r==8'HA3) ? ~clk16x : clk16x ;

end

 

 

reg[4:0] clk1d4r;

always @(posedge clk16x or posedge rst)

begin

if (rst)

clk1d4r = 5'b00000 ;

else 

clk1d4r = clk1d4r +1 ;

end

wire clk1d4 = clk1d4r[4];

 

wire data_ok = data_ready& ~framing_error & ~parity_error ;

wire tbre;//Status signal indication that the transmitter buffer register is empty

//CASE BRANCH

parameter IDLE = 3'h0,LOAD1 = 3'h1,LOAD2 = 3'h4, STORE=3'h2,WAIT_TX=3'h3 ;

reg[2:0] State;

always @(posedge clk1d4 or posedge rst)

  if(rst)

    State <= #`Tgate IDLE;

  else

    case(State)

    IDLE : 

      if(data_ok) 

        State <=  #`Tgate LOAD1;

      else

        State <=  #`Tgate IDLE;

    LOAD1 :

      State <= #`Tgate LOAD2;

    LOAD2 :

      State <= #`Tgate STORE;

    STORE : 

      State <= #`Tgate WAIT_TX;

    WAIT_TX :

      if(!tbre) 

        State <=  #`Tgate IDLE;

      else

        State <= #`Tgate WAIT_TX;

    default : State <= #`Tgate IDLE;

    endcase

 

reg rdn,wrn;

wire[7:0] dout;

reg[7:0] din;

//Execute

always @(posedge clk1d4 or posedge rst)

  if(rst)

    begin

      rdn <= #`Tgate 1'b1;

      wrn <= #`Tgate 1'b1;

      din <= #`Tgate 8'hEE;

    end

  else

    case(State)

    IDLE : 

      begin

      rdn <= #`Tgate 1'b1;

      wrn <= #`Tgate 1'b1;

      din <= #`Tgate 8'hEE;

      end

    LOAD1 :

      begin

      rdn <= #`Tgate 1'b0;

      wrn <= #`Tgate 1'b1;

      din <= #`Tgate 8'hEE;

      end

    LOAD2 :

      begin

      rdn <= #`Tgate 1'b0;

      wrn <= #`Tgate 1'b1;

      din <= #`Tgate dout;

      end

    STORE : 

      begin

      rdn <= #`Tgate 1'b1;

      wrn <= #`Tgate 1'b0;

      din <= #`Tgate din;

      end

    WAIT_TX :

      begin

      rdn <= #`Tgate 1'b1;

      wrn <= #`Tgate 1'b1;

      din <= #`Tgate 8'hEE;

      end

    default : 

      begin

      rdn <= #`Tgate 1'b1;

      wrn <= #`Tgate 1'b1;

      din <= #`Tgate 8'hEE;

      end

    endcase

 

uart i_uart(

dout,data_ready,framing_error,parity_error,rxd,clk16x,rst,rdn,din,tbre,tsre,wrn,sdo);

 

endmodule