slp.conf

SLP协议在linux下的实现。此版本为1.2.1版。官方网站为www.openslp.org

#############################################################################
#
# OpenSLP configuration file
#
# Format and contents conform to specification in IETF RFC 2614 so the
# comments use the language of the RFC.  In OpenSLP, SLPD operates as an SA
# and a DA.  The SLP UA functionality is encapsulated by SLPLIB.
#
#############################################################################


#----------------------------------------------------------------------------
# Static Scope and Static DA Configuration
#----------------------------------------------------------------------------

# This option is a comma delimited list of strings indicating the only scopes
# a UA or SA is allowed when making requests or registering or the scopes a
# DA must support. (default value is "DEFAULT")
;net.slp.useScopes = myScope1, myScope2, myScope3

# Allows administrator to force UA and SA agents to use specific DAs.  If
# this setting is not used dynamic DA discovery will be used to determine
# which DAs to use.  (Default is to use dynamic DA discovery)
;net.slp.DAAddresses = myDa1,myDa2,myDa3


#----------------------------------------------------------------------------
# DA Specific Configuration
#----------------------------------------------------------------------------

# Enables slpd to function as a DA. Only a very few DAs should exist.  It 
# is suggested that the administrator read the OpenSLP users guide before
# enabling this setting. Default is false.  Uncomment the line below to 
# enable DA operation.
;net.slp.isDA = true

# A 32 bit integer giving the number of seconds for the DA heartbeat. 
# Default is 3 hours (10800 seconds).  This property corresponds to
# the protocol specification parameter CONFIG_DA_BEAT [7].  Ignored 
# if isDA is false.
;net.slp.DAHeartBeat = 10800


#----------------------------------------------------------------------------
# SA Specific Configuration
#----------------------------------------------------------------------------

# If net.slp.watchRegistrationPID is set to true, local registrations made
# with the SA via the SLPReg() API call will be monitored.  If the PID of the
# process (and/or thread on Linux) disappears (the registering process died
# unexpectedly with out calling SLPDereg()), then the registration is 
# automatically de-registered.  (Default value is true.  Uncomment the line
# below to disable PID watching.
;net.slp.watchRegistrationPID = false


#----------------------------------------------------------------------------
# UA Specific Configuration
#----------------------------------------------------------------------------
# A 32 bit integer giving the maximum number of results to accumulate and 
# return for a synchronous request before the timeout, or the maximum number
# of results to return through a callback if the request results are 
# reported asynchronously (default value is 256).
;net.slp.maxResults = 256


#----------------------------------------------------------------------------
# Network Configuration Properties
#----------------------------------------------------------------------------

# Force broadcasts to be used instead of multicast. This setting is seldom
# necessary since OpenSLP will automatically use broadcast if multicast
# is unavailable. (Default is false)
;net.slp.isBroadcastOnly = true

# A boolean indicating whether passive DA detection should be used.
# Default is true.  Uncomment the following line to disable passive DA 
# detection
;net.slp.passiveDADetection = false

# A boolean indicating whether active DA detection should be used. This is
# useful when the DAs available are explicitly restricted to those obtained
# from DHCP or the net.slp.DAAddresses property. Default is true.  Uncomment
# the following line to disable active DA detection
;net.slp.activeDADetection = false

# The net.slp.DAActiveDiscoveryInterval property controls *periodic* 
# transmission of active DA discovery SrvRqsts.  The default setting
# of 1 which disables sending periodic active DA discovery SrvRqsts.  
# However, even if net.slp.DAActiveDiscoveryInterval=1 OpenSLP agents will
# send a send active DA request only upon initialization.  To disable all 
# active DA detection you MUST net.slp.passiveDADetection = false. (you
# may also set net.slp.DAActiveDiscoveryInterval=0)
# simply set 
;net.slp.DAActiveDiscoveryInterval = 1

# A positive integer that is less than or equal to 255. (The default is  255)
;net.slp.multicastTTL = 255

# An integer giving the maximum amount of time (in milliseconds) to perform
# active DA discovery requests. (Default is 2000 ms or 2 secs).
;net.slp.DADiscoveryMaximumWait = 2000

# A value-list of 32 bit integers used as timeouts, in milliseconds, to 
# implement the multicast convergence algorithm during active DA discovery.
# Each value specifies the time to wait before sending the next request, or
# until nothing new has been learned from two successive requests. 
# Default is:  500,750,1000,1500,2000,3000.
;net.slp.DADiscoveryTimeouts = 500,750,1000,1500,2000,3000

# An integer giving the maximum amount of time (in milliseconds) to perform
# multicast requests. (Default is 5000 ms or 5 secs).
;net.slp.multicastMaximumWait = 5000

# A value-list of 32 bit integers used as timeouts, in milliseconds, to
# implement the multicast convergence algorithm.  Each value specifies
# the time to wait before sending the next request, or until nothing new 
# has been learned from two successive requests.  
# Default is:  500,750,1000,1500,2000,3000.  In a slow network the less
# aggressive values of 3000,3000,3000,3000,3000 allow better performance.  
;net.slp.multicastTimeouts  = 500,750,1000,1500,2000,3000

# An integer giving the maximum amount of time (in milliseconds) to perform
# unicast requests. (Default is 5000 ms or 5 secs).
;net.slp.unicastMaximumWait = 5000 

# A value-list of 32 bit integers used as timeouts, in milliseconds, to 
# implement unicast datagram transmission to DAs.  The nth value gives
# the time to block waiting for a reply on the nth try to contact the DA.
# Currently OpenSLP uses TCP for all unicast communication so this setting
# does not do anything
;net.slp.unicastTimeouts  = 500,750,1000,1500,2000,3000

# To OpenSLP the following is the same as net.slp.unicastTimeouts.  Use 
# net.slp.unicastTimeouts instead.
;net.slp.datagramTimeouts = IGNORED

# An integer giving the maximum value for all random wait parameters.
# (Default is 5000 or 5 sec)
;net.slp.randomWaitBound = 5000

# A integer giving the network packet MTU in bytes. (Default is 1400)
;net.slp.MTU = 1400

# A list of IP address of network interfaces on which the DA/SA should listen
# for slp requests.  By default, slpd will use all interfaces.
;net.slp.interfaces = 1.2.3.4,1.2.3.5,1.2.3.6


#----------------------------------------------------------------------------
# Security
#----------------------------------------------------------------------------
# A boolean indicating whether the agent should enable security for URLs,
# attribute lists, DAAdverts, and SAAdverts.  (Default setting is false and 
# ENABLE_SECURITY code must be compiled)
;net.slp.securityEnabled=true

# A boolean indicating whether the DA or SA will only allow deregistrations 
# and re-registration from the *exact* host that made the registration. 
# Default setting if true.   Uncomment the line below to disable source 
# address checking.
;net.slp.checkSourceAddr=false


#----------------------------------------------------------------------------
# Tracing and Logging
#----------------------------------------------------------------------------

# A boolean controlling printing of messages about traffic with DAs.  
# Default is false.  Uncomment the following line to enable DA traffic 
# tracing
;net.slp.traceDATraffic = true

# A boolean controlling dumps of all registered services upon registration 
# and deregistration.  If true, the contents of the DA or SA server are 
# dumped after a registration or deregistration occurs.  Default is false.
# Uncommment the following line to enable registration message logging
;net.slp.traceReg = true

# A boolean controlling printing details when a SLP message is dropped for 
# any reason.  Default is false.  Uncomment the following line to trace all
# dropped messages
;net.slp.traceDrop = true

# A boolean controlling printing of details on SLP messages. The fields in 
# all incoming messages and outgoing replies are printed.  Very verbose.
# Default is false. Uncomment the following line to enable verbose message
# tracing.
;net.slp.traceMsg = true


#----------------------------------------------------------------------------
# Serialized Proxy Registration
#----------------------------------------------------------------------------
# The net.slp.serializedRegURL is not supported by net.slp.serializeRegURL.
#
# slpd accepts the [-r] command line parameter that specifies the serialized
# registration file.  The default serialized registration file is 
# /etc/slp.reg