p&e_fcs.ini

基于Freescale-smac的点对点通讯。 简介：在Router(特征：接口为COM口)上实现点对点通信。 子工程： 1、接收端receiver_13213_ver2.0 （目前只

[HI-WAVE]
Target=HCS08ICDCYCLMULT
CPU=HCS08
MainFrame=2,3,-1,-1,-1,-1,0,63,768,545
TOOLBAR=57600 57601 32795 0 57635 57634 57637 0 57671 57669 0 32777 32776 32782 32780 32781 32778 0 32806
LoadDialogOptions=
Configuration=P&E_FCS.hwc
Layout=P&E_FCS.hwl
Statusbar=1
ShowToolbar=1
Smallborder=0
Hideheadline=0
Hidetitle=0
[PEDebug]
SHOWPROT=0
CMDFILE0=CMDFILE STARTUP ON "startup.cmd"
CMDFILE1=CMDFILE RESET ON "reset.cmd"
CMDFILE2=CMDFILE PRELOAD ON "preload.cmd"
CMDFILE3=CMDFILE POSTLOAD ON "postload.cmd"
TRACE_ENABLEDISABLESTATE=0
CURRENTDEVICE=9S08GT60
CURRENTMODE=4
ASK_BEFORE_ERASING_FLASH=1
DBG0=DBG GENERAL DISARM_ON PROTECT_OFF ANALYZE_ON STEPATRUN_ON
DBG1=DBG USER 0x0 0x0
DBG2=DBG PREDEFINED SELECT 0 END STOP 0x0
AUTO_SYNC=1
[DEVICE]
CHIPMODE=9S08GT60
[HC908GP32]
PROGRAMMING_ALGORITHM=0
DOTRIM=1
[PORT]
COMPORT=1
IP=
STOPBITS=2
[DTRCONTROL]
POWERDOWNDELAY=250
POWERUPDELAY=500
[TARGETTYPE]
TARGETTYPE=0
DEVICE_TYPE=5
DEVICE_DIVIDER=0
MON08_POWERTYPE=0
MON08_CLOCKTYPE=1
MON08_OUTPUTCLOCK=1
CYCLONE_COMLINE_IS_MON4=1
PEMON08POWERDOWNONSOFTWAREEXIT=0
pemon08_interface_detected=0
pemon08_interface_detected_at_some_point=0
PEMON08_MAJOR_VERSION=0
PEMON08_MINOR_VERSION=0
delay_11_bits_cycles=0
Irq_during_powerdown=0
Irq_during_monitorentry=2
Irq_during_monitormode=2
Reset_during_powerdown=0
Reset_during_monitorentry=2
Reset_during_monitormode=2
[ICD08]
KX_CONFIG1_VALUE=0
[MON08]
PORT_RESET_VALUE=174
JDSOIA=0
[SETTINGS]
MEMORYSTART2=0
MEMORYSTART1=128
DEFAULT_SOURCE_PATH=C:\Program Files\Freescale\CW08 V5.0\prog
[CycleWin]
XTAL=9830400
[9S08GT60]
PROGRAMMING_ALGORITHM=0
DOTRIM=1
[STARTUP12]
show_hstep_assembly_details=0
[STARTUP]
CPUTARGETTYPE=0
IO_DELAY_SET=0
IO_DELAY_CNT=29
PCI_DELAY=2
RESET_DELAY=0
PORT=21
interface_selection=1
SHOWDIALOG=1
USE_RESET_PIN=1
USE_CYCLONEPRO_RELAYS=0
CyclonePro_poweroffonexit=0
CyclonePro_currentvoltage=255
CyclonePro_PowerDownDelay=250
CyclonePro_PowerUpDelay=250






[SAVESETTINGS]
S19FILENAME=
PRGFILENAME=
PRGFILEPATH=E:\Program Files\Freescale\CW08 V5.0\prog
SERIALFILENAME=

[Recent Applications File List]
File1=
File2=
File3=
File4=D:\Profiles\A20639\Desktop\SMAC4.1\S08\tools\Embedded_Bootloader\AX-0308RevC\Embedded_Bootloader_V501_AXIOM0308.s19
LoadFlags1=
LoadFlags2=
LoadFlags3=
LoadFlags4=3
File0=F:\Freescale\SMAC 4.2\S08\apps\receiver_13213_ver2.0\3.1\bin\wireless_uart_13213_NCB.abs
LoadFlags0=


[Recent HI-WAVE FindProcedure Search]
Search0=main
Search1=IRQIsr
Search2=RAMDrvReadRx
Search3=RAMDrvRx
Search4=IsrIRQ
Search5=UseExternalClock
[9S08GB60]
PROGRAMMING_ALGORITHM=0
DOTRIM=1

[Recent Layout File List]
File1=
File2=
File3=
File4=
File0=P&E_FCS.hwl

[HCS08ICDCYCLMULT]
CURRENTDEVICE=9S08GT60
CURRENTMODE=4
SHOWPROT=0
CMDFILE0=CMDFILE STARTUP ON "startup.cmd"
CMDFILE1=CMDFILE RESET ON "reset.cmd"
CMDFILE2=CMDFILE PRELOAD ON "preload.cmd"
CMDFILE3=CMDFILE POSTLOAD ON "postload.cmd"
TRACE_ENABLEDISABLESTATE=0
ASK_BEFORE_ERASING_FLASH=1
AUTO_SYNC=1
DBG0=DBG GENERAL DISARM_ON PROTECT_OFF ANALYZE_ON STEPATRUN_ON
DBG1=DBG USER 0x0 0x0
DBG2=DBG PREDEFINED SELECT 0
DBG3=DBG PREDEFINED DBGENGINE END STOP 0x0

[HCS08FCS]
CURRENTDEVICE=9S08GT60
CURRENTMODE=4
SHOWPROT=0
CMDFILE0=CMDFILE STARTUP ON "startup.cmd"
CMDFILE1=CMDFILE RESET ON "reset.cmd"
CMDFILE2=CMDFILE PRELOAD ON "preload.cmd"
CMDFILE3=CMDFILE POSTLOAD ON "postload.cmd"
TRACE_ENABLEDISABLESTATE=0
ASK_BEFORE_ERASING_FLASH=1
AUTO_SYNC=1
DBG0=DBG GENERAL DISARM_ON PROTECT_OFF ANALYZE_ON STEPATRUN_ON
DBG1=DBG USER 0x0 0x0
DBG2=DBG PREDEFINED SELECT 0 END STOP 0x0