bspuicc_phy.h

MMI层OBJ不能完全编译

/*=============================================================================
 *    Copyright 2001-2002 Texas Instruments Inc. All rights reserved.
 */
#ifndef BSP_UICC_PHY_HEADER

#define BSP_UICC_PHY_HEADER
/*=============================================================================
 * Component Description:
 *    Header file for the Usim block specific functions
 */

/*=============================================================================*/

/*!
 * @#define BSP_UICC_READ_TIMEOUT_VALUE
 * 
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the sim timeout value ~ 18seconds
 */
#define BSP_UICC_READ_TIMEOUT_VALUE 0x2000

/*!
 * @typedef BspUicc_Phy_ReturnCode
 * 
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for the return code
 */
enum
{
    BSP_UICC_PHY_RETURN_CODE_FAILURE    = (-1),
    BSP_UICC_PHY_RETURN_CODE_SUCCESS    = (0)
};
typedef SYS_WORD16 BspUicc_Phy_ReturnCode;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_Protocol
 * 
 * @discussion
 * <b> Description  </b><br>
 *   Specifies the type for the Protocol used (Char or Block).
 */
enum
{
    BSP_UICC_PHY_T0_PROTOCOL            = 0,
    BSP_UICC_PHY_T1_PROTOCOL            = 1
};
typedef SYS_UWORD8 BspUicc_Phy_Protocol;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_ClockStop
 * 
 * @discussion
 * <b> Description  </b><br>
 *   Specifies the type for Clock stop parameter used to enable/disable sleep mode
 */
enum
{
    BSP_UICC_PHY_CLOCK_STOP_DISABLE = 0,
    BSP_UICC_PHY_CLOCK_STOP_ENABLE  = 1
};
typedef SYS_UWORD8 BspUicc_Phy_ClockStop;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_SClockLevel
 * 
 * @discussion
 * <b> Description  </b><br>
 *   Specifies the type for Clock stop parameter used to enable/disable sleep mode
 */
enum
{
    BSP_UICC_PHY_SCLOCK_NO_STOP    = 0, /* Clock stop is not Supported */
    BSP_UICC_PHY_SCLOCK_LEVEL_LOW  = 1,
    BSP_UICC_PHY_SCLOCK_LEVEL_HIGH = 2
};
typedef SYS_UWORD8 BspUicc_Phy_SClkLev;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_SclkDiv
 * 
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for number of Sclock division configuration paramater.
 */
enum
{
    BSP_UICC_PHY_SCLKDIV_13_2           = 0, /* for 13/2 MHz */
    BSP_UICC_PHY_SCLKDIV_13_4           = 1, /* for 13/4 MHz */
    BSP_UICC_PHY_SCLKDIV_13_8           = 2, /* for 13/8 MHz */
    BSP_UICC_PHY_SCLKDIV_13_1           = 3  /* for 13 MHz */
};
typedef SYS_UWORD8 BspUicc_Phy_SclkDiv;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_EtuPeriod
 * 
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for Elementary Time unit configuration paramater.
 */
enum
{
    BSP_UICC_PHY_ETU_PERIOD_8      = 0,  /* for 8 times 1/F sclk */
    BSP_UICC_PHY_ETU_PERIOD_372    = 1,
    BSP_UICC_PHY_ETU_PERIOD_512_8  = 2,
    BSP_UICC_PHY_ETU_PERIOD_512_16 = 3
};
typedef SYS_UWORD8 BspUicc_Phy_EtuPeriod;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_DataSize
 * 
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for Number of data units.
 */
typedef volatile SYS_UWORD16    BspUicc_Phy_DataSize;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_TxData
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for Data being transmitted/written.
 */
typedef volatile SYS_UWORD8     BspUicc_Phy_TxData;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_RxData
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for Data being received/read.
 *  Rx is bigger than a byte to accomodate a parity bit if needed.
 */
typedef volatile SYS_UWORD8    BspUicc_Phy_RxData;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_FifoData
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for Data in the Fifo
 */
typedef SYS_UWORD16 BspUicc_Phy_FifoData;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_TxFifoSize
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for size of the FIFO in the hardware.
 */
typedef SYS_UWORD16    BspUicc_Phy_TxFifoSize;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_RxFifoSize
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for size of the FIFO in the hardware.
 */
typedef SYS_UWORD16    BspUicc_Phy_RxFifoSize;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_Cgt
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for Character Guard Time.
 */
typedef SYS_UWORD16    BspUicc_Phy_Cgt;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_Cwt
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for Character Wait Time.
 */
typedef SYS_UWORD16    BspUicc_Phy_Cwt;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_Bwt
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for of Block Wait Time.
 */
typedef SYS_UWORD32    BspUicc_Phy_Bwt;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_FiValue
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for F value used in calculating ETU.
 */
typedef SYS_UWORD16    BspUicc_Phy_FiValue;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_DiValue
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for D value used in calculating ETU.
 */
typedef SYS_UWORD16    BspUicc_Phy_DiValue;

/*============================================================================= */
/*!
 * @typedef BspUicc_Phy_WaitI
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for WaitI configuration parameter
 */
typedef SYS_UWORD16    BspUicc_Phy_WaitI;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_Error
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type Physical layer errors
 */
enum
{
    BSP_UICC_PHY_NO_ERROR                   = ( 0 ),
    BSP_UICC_PHY_NATR_ERROR                 = ( -2 ),
    BSP_UICC_PHY_CHAR_UNDERFLOW_ERROR       = ( -3 ),
    BSP_UICC_PHY_CHAR_OVERFLOW_ERROR        = ( -4 ),
    BSP_UICC_PHY_CHAR_TIMEOUT_ERROR         = ( -5 ),
    BSP_UICC_PHY_BLOCK_TIMEOUT_ERROR        = ( -6 ),
    BSP_UICC_PHY_MAX_RESENT_ERROR           = ( -7 ),
    BSP_UICC_PHY_TS_DECODE_ERROR            = ( -8 ),
    BSP_UICC_PHY_NO_CARD_PRESENT_ERROR      = ( -9 ),
    BSP_UICC_PHY_READ_TIMEOUT_ERROR         = ( -10 )
};
typedef SYS_WORD16 BspUicc_Phy_Error;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_Convention
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for Physical layer data Code Convention
 */
enum
{
    BSP_UICC_PHY_CONVENTION_DIRECT          = 0,
    BSP_UICC_PHY_CONVENTION_INVERSE         = 1
};
typedef SYS_UWORD8 BspUicc_Phy_Convention;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_PowerLevel
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for the card power level configuration
 * This is encoded as per section 6.5.6 in ISO/IEC 7816-3
 */
enum
{
    BSP_UICC_PHY_POWER_LEVEL_18             = 4,
    BSP_UICC_PHY_POWER_LEVEL_3_OR_5         = 3,
    BSP_UICC_PHY_POWER_LEVEL_3              = 2,
    BSP_UICC_PHY_POWER_LEVEL_5              = 1
};
typedef SYS_UWORD16 BspUicc_Phy_PowerLevel;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_BlockSize
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for the size of a block
 */
typedef SYS_UWORD16 BspUicc_Phy_BlockSize;

/*=============================================================================*/
/*!
 * @typedef BspUicc_Phy_ClkStopInd
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for the Clock Stop Indicator in ATR
 */
typedef SYS_UWORD16 BspUicc_Phy_ClkStopInd;

/*============================================================================= */
/*!
 * @typedef BspUicc_Phy_ConfigType
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the type for WaitI configuration parameter
 */
enum
{
    BSP_UICC_PHY_CONFIG_TYPE_RESET          = 0,
    BSP_UICC_PHY_CONFIG_TYPE_READ_WRITE     = 1,
    BSP_UICC_PHY_CONFIG_TYPE_BWT_UPDATE     = 2,
    BSP_UICC_PHY_CONFIG_TYPE_CLKSTOP_UPDATE = 3     
};
typedef SYS_UWORD8  BspUicc_Phy_ConfigType;


/*============================================================================= */
/*!
 * @define
 *
 * @discussion
 * <b> Description  </b><br>
 *  The max Fifo size in the Usim hardware block. 
 */
#define BSP_UICC_PHY_MAX_FIFO_SIZE          16

/*============================================================================= */
/*!
 * @typedef BspUicc_Phy_Mode
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the ATR Mode, PPS Mode or READ_WRITE  Mode
 *  ReadWrite mode is used after a PPS i.e. for Commands.
 */
enum
{
    BSP_UICC_PHY_MODE_ATR            = 0,
    BSP_UICC_PHY_MODE_PPS            = 1, 
    BSP_UICC_PHY_MODE_READ_WRITE     = 2
};
typedef SYS_UWORD8  BspUicc_Phy_Mode;

/*============================================================================= */
/*!
 * @typedef  BspUicc_Phy_Direction
 *
 * @discussion
 * <b> Description  </b><br>
 *  Specifies the Tx or Rx Direction
 */
enum
{
    BSP_UICC_PHY_DIRECTION_RX        = 1,
    BSP_UICC_PHY_DIRECTION_TX        = 2
};
typedef SYS_UWORD8  BspUicc_Phy_Direction;

/*============================================================================= */
/*!
 * @typedef BspUicc_Phy_RxCtrl
 *
 * @discussion
 * <b> Description  </b><br>
 *  Control data for Receive mode
 */
typedef struct
{
    BspUicc_Phy_DataSize             rxIndex;
    BspUicc_Phy_DataSize             outIndex;