c_start.c

ucos在9200上的移植

	unsigned int 	pllDivider,pllMultiplier;

/////////////////////////////////////////////////////////////////////////////////////////////////////
// Optionnal
/////////////////////////////////////////////////////////////////////////////////////////////////////

	//* Check if Input & Output Frequencies are in the correct range

	MainClock 		= AT91F_CKGR_GetMainClock(AT91C_BASE_CKGR,SLOWCLOCK);

	pllDivider    	= (PLLAR_Register  & AT91C_CKGR_DIVA);
	pllMultiplier 	= ((PLLAR_Register  & AT91C_CKGR_MULA) >> 16) + 1;
	if(AT91F_CheckPLL_FrequencyRange(MainClock, pllDivider , pllMultiplier) == FALSE)
		return FALSE;

	pllDivider    	= (PLLBR_Register  & AT91C_CKGR_DIVB);
	pllMultiplier 	= ((PLLBR_Register  & AT91C_CKGR_MULB) >> 16) + 1;
	if(AT91F_CheckPLL_FrequencyRange(MainClock, pllDivider , pllMultiplier) == FALSE)
		return FALSE;

/////////////////////////////////////////////////////////////////////////////////////////////////////
// Step 3.
// Setting PLLA and Divider A
/////////////////////////////////////////////////////////////////////////////////////////////////////

	AT91C_BASE_CKGR->CKGR_PLLAR = PLLAR_Register;
	//* Wait for PLLA stabilization LOCKA bit in PMC_SR
	tmp = 0;
	while( !(AT91C_BASE_PMC->PMC_SR & AT91C_PMC_LOCKA) && (tmp++ < DELAY_PLL) ) ;

/////////////////////////////////////////////////////////////////////////////////////////////////////
// Step 4.
// Setting PLLB and Divider B
/////////////////////////////////////////////////////////////////////////////////////////////////////

	AT91C_BASE_CKGR->CKGR_PLLBR = PLLBR_Register;
	//* Wait for PLLB stabilization LOCKB bit in PMC_SR
	tmp = 0;
	while( !(AT91C_BASE_PMC->PMC_SR & AT91C_PMC_LOCKB) && (tmp++ < DELAY_PLL) ) ;

/////////////////////////////////////////////////////////////////////////////////////////////////////
// Step 5.
// Selection of Master Clock MCK (and Processor Clock PCK)
/////////////////////////////////////////////////////////////////////////////////////////////////////

	//* Constraints of the Master Clock selection sequence
	//* Write in the MCKR dirty value concerning the clock selection CSS then overwrite it in a second sequence
	
	AT91C_BASE_PMC->PMC_MCKR =0x1;//AT91C_PMC_CSS_SLOW_CLK;
	//* Wait until the master clock is established
	tmp = 0;
	while( !(AT91C_BASE_PMC->PMC_SR & AT91C_PMC_MCKRDY) && (tmp++ < DELAY_MAIN_FREQ) );

	//* Second sequence
	AT91C_BASE_PMC->PMC_MCKR =MCKR;
	//* Wait until the master clock is established
	tmp = 0;
	while( !(AT91C_BASE_PMC->PMC_SR & AT91C_PMC_MCKRDY) && (tmp++ < DELAY_MAIN_FREQ) );

	return TRUE;
}
//*----------------------------------------------------------------------------
//* \fn    AT91F_InitSDRAM
//* \brief This function performs very low level HW initialisation
//*----------------------------------------------------------------------------
void AT91F_InitSDRAM()
{
	volatile int *pRegister;
	AT91PS_PIO pPio = AT91C_BASE_PIOC;
	
	/* Configure PIOC as peripheral (D16/D31) */
	pPio->PIO_ASR = 0xFFFF0000;
	pPio->PIO_BSR = 0x0;
	pPio->PIO_PDR = 0xFFFF0000;
	
	/* Setup MEMC to support all connected memories (CS0 = FLASH; CS1=SDRAM) */
	pRegister = (int *)0xFFFFFF60;
	*pRegister = 0x02; 
	
	/* Init SDRAM */
	pRegister = (int *)0xFFFFFF98;
	*pRegister =0x2A88C140; 
	pRegister = (int *)0xFFFFFF90;
	*pRegister = 0x2; 
	pRegister = (int *)0x20000000;
	*pRegister = 0; 
	pRegister = (int *)0xFFFFFF90;
	*pRegister = 0x4; 
	pRegister = (int *)0x20000000;
	*pRegister = 0; 
	*pRegister = 0; 
	*pRegister = 0; 
	*pRegister = 0; 
	*pRegister = 0; 
	*pRegister = 0; 
	*pRegister = 0; 
	*pRegister = 0; 
	pRegister = (int *)0xFFFFFF90;
	*pRegister = 0x3; 
	pRegister = (int *)0x20000080;
	*pRegister = 0; 
	pRegister = (int *)0xFFFFFF94;
	*pRegister = 0x2e0; 
	pRegister = (int *)0x20000000;
	*pRegister = 0; 
	pRegister = (int *)0xFFFFFF90;
	*pRegister = 0x00; 
	pRegister = (int *)0x20000000;
	*pRegister = 0; 
}


//*----------------------------------------------------------------------------
//* \fn    AT91F_InitFlash
//* \brief This function performs very low level HW initialization
//*----------------------------------------------------------------------------
void AT91F_InitFlash()
{
	AT91C_BASE_MC->MC_PUIA[0] = AT91C_MC_PROT_PRWURW;
	AT91C_BASE_MC->MC_PUP = 0;
	AT91C_BASE_MC->MC_PUER =0;	//* Memory controller protection unit disable
	AT91C_BASE_MC->MC_ASR = 0;  //* read only!
	AT91C_BASE_MC->MC_AASR = 0; //* read only!

	//* Setup MEMC to support CS0=Flash
	AT91C_BASE_EBI->EBI_CSA |= AT91C_EBI_CS0A_SMC;
	AT91C_BASE_EBI->EBI_CFGR = (AT91C_EBI_DBPUC & 0x00) | (AT91C_EBI_EBSEN & 0x00);

	//* Setup Flash
	AT91C_BASE_SMC2->SMC2_CSR[0] = (AT91C_SMC2_NWS & 0x4) | AT91C_SMC2_WSEN
									| (AT91C_SMC2_TDF & 0x200) | AT91C_SMC2_BAT | AT91C_SMC2_DBW_16;
}


//*----------------------------------------------------------------------------
//* \fn    AT91F_LowLevelInit
//* \brief This function performs very low level HW initialization
//*----------------------------------------------------------------------------
extern void AT91F_LowLevelInit()
{
	unsigned char 	status;

    //step1
    status = AT91F_WaitForMainClockFrequency();
    
    //step2
    AT91F_InitFlash();
    
    //step3 init clock
    status = AT91F_InitClocks(PLLAR,PLLBR,MCKR);
    
    //step4 configuare sdram
    AT91F_InitSDRAM();
    
    // Init Interrupt Controller
	AT91F_AIC_Open(
		AT91C_BASE_AIC,          // pointer to the AIC registers
		AT91C_AIC_BRANCH_OPCODE, // IRQ exception vector
		AT91F_UndefHandler,      // FIQ exception vector
		AT91F_UndefHandler,      // AIC default handler
		AT91F_SpuriousHandler,   // AIC spurious handler
		0);                      // Protect mode
		
	// Perform 8 End Of Interrupt Command to make sure AIC will not Lock out nIRQ 
	AT91F_AIC_AcknowledgeIt(AT91C_BASE_AIC);
	AT91F_AIC_AcknowledgeIt(AT91C_BASE_AIC);
	AT91F_AIC_AcknowledgeIt(AT91C_BASE_AIC);
	AT91F_AIC_AcknowledgeIt(AT91C_BASE_AIC);
	AT91F_AIC_AcknowledgeIt(AT91C_BASE_AIC);
	AT91F_AIC_AcknowledgeIt(AT91C_BASE_AIC);
	AT91F_AIC_AcknowledgeIt(AT91C_BASE_AIC);
	AT91F_AIC_AcknowledgeIt(AT91C_BASE_AIC);

    //step5 usart0 init
    //AT91F_US0_Init();
    	
    AT91F_DBGU_CfgPIO();

	// Configure DBGU
	AT91F_US_Configure (
		(AT91PS_USART) AT91C_BASE_DBGU,          			// DBGU base address
		60000000,                  							// 60 MHz
		AT91C_US_CHMODE_NORMAL | AT91C_US_PAR_NONE ,        // mode Register to be programmed
		115200 ,                   							// baudrate to be programmed
		0);                        							// timeguard to be programmed

	// Enable Transmitter
	AT91F_US_EnableTx((AT91PS_USART) AT91C_BASE_DBGU);

	AT91F_DBGU_Printk("\n\rAT91F_LowLevelInit() Complete in Flash!\n\r");

}