kconfig

LINUX 2.6.17.4的源码

	  You should never need this option, say N.

config PC300
	tristate "Cyclades-PC300 support (RS-232/V.35, X.21, T1/E1 boards)"
	depends on HDLC && PCI
	---help---
	  Driver for the Cyclades-PC300 synchronous communication boards.

	  These boards provide synchronous serial interfaces to your
	  Linux box (interfaces currently available are RS-232/V.35, X.21 and
	  T1/E1). If you wish to support Multilink PPP, please select the
	  option later and read the file README.mlppp provided by PC300
	  package.

	  To compile this as a module, choose M here: the module
	  will be called pc300.

	  If unsure, say N.

config PC300_MLPPP
	bool "Cyclades-PC300 MLPPP support"
	depends on PC300 && PPP_MULTILINK && PPP_SYNC_TTY && HDLC_PPP
	help
	  Multilink PPP over the PC300 synchronous communication boards.

comment "Cyclades-PC300 MLPPP support is disabled."
	depends on WAN && HDLC && PC300 && (PPP=n || !PPP_MULTILINK || PPP_SYNC_TTY=n || !HDLC_PPP)

comment "Refer to the file README.mlppp, provided by PC300 package."
	depends on WAN && HDLC && PC300 && (PPP=n || !PPP_MULTILINK || PPP_SYNC_TTY=n || !HDLC_PPP)

config N2
	tristate "SDL RISCom/N2 support"
	depends on HDLC && ISA
	help
	  Driver for RISCom/N2 single or dual channel ISA cards by
	  SDL Communications Inc.

	  If you have such a card, say Y here and see
	  <http://www.kernel.org/pub/linux/utils/net/hdlc/>.

	  Note that N2csu and N2dds cards are not supported by this driver.

	  To compile this driver as a module, choose M here: the module
	  will be called n2.

	  If unsure, say N.

config C101
	tristate "Moxa C101 support"
	depends on HDLC && ISA
	help
	  Driver for C101 SuperSync ISA cards by Moxa Technologies Co., Ltd.

	  If you have such a card, say Y here and see
	  <http://www.kernel.org/pub/linux/utils/net/hdlc/>.

	  To compile this driver as a module, choose M here: the
	  module will be called c101.

	  If unsure, say N.

config FARSYNC
	tristate "FarSync T-Series support"
	depends on HDLC && PCI
	---help---
	  Support for the FarSync T-Series X.21 (and V.35/V.24) cards by
	  FarSite Communications Ltd.

	  Synchronous communication is supported on all ports at speeds up to
	  8Mb/s (128K on V.24) using synchronous PPP, Cisco HDLC, raw HDLC,
	  Frame Relay or X.25/LAPB.

	  If you want the module to be automatically loaded when the interface
	  is referenced then you should add "alias hdlcX farsync" to
	  /etc/modprobe.conf for each interface, where X is 0, 1, 2, ..., or
	  simply use "alias hdlc* farsync" to indicate all of them.

	  To compile this driver as a module, choose M here: the
	  module will be called farsync.

config DLCI
	tristate "Frame Relay DLCI support"
	depends on WAN
	---help---
	  Support for the Frame Relay protocol.

	  Frame Relay is a fast low-cost way to connect to a remote Internet
	  access provider or to form a private wide area network. The one
	  physical line from your box to the local "switch" (i.e. the entry
	  point to the Frame Relay network, usually at the phone company) can
	  carry several logical point-to-point connections to other computers
	  connected to the Frame Relay network. For a general explanation of
	  the protocol, check out <http://www.mplsforum.org/>.

	  To use frame relay, you need supporting hardware (called FRAD) and
	  certain programs from the net-tools package as explained in
	  <file:Documentation/networking/framerelay.txt>.

	  To compile this driver as a module, choose M here: the
	  module will be called dlci.

config DLCI_COUNT
	int "Max open DLCI"
	depends on DLCI
	default "24"
	help
	  Maximal number of logical point-to-point frame relay connections
	  (the identifiers of which are called DCLIs) that the driver can
	  handle.

	  The default is probably fine.

config DLCI_MAX
	int "Max DLCI per device"
	depends on DLCI
	default "8"
	help
	  How many logical point-to-point frame relay connections (the
	  identifiers of which are called DCLIs) should be handled by each
	  of your hardware frame relay access devices.

	  Go with the default.

config SDLA
	tristate "SDLA (Sangoma S502/S508) support"
	depends on DLCI && ISA
	help
	  Driver for the Sangoma S502A, S502E, and S508 Frame Relay Access
	  Devices.

	  These are multi-protocol cards, but only Frame Relay is supported
	  by the driver at this time. Please read
	  <file:Documentation/networking/framerelay.txt>.

	  To compile this driver as a module, choose M here: the
	  module will be called sdla.

# Wan router core.
config WAN_ROUTER_DRIVERS
	bool "WAN router drivers"
	depends on WAN && WAN_ROUTER
	---help---
	  Connect LAN to WAN via Linux box.

	  Select driver your card and remember to say Y to "Wan Router."
	  You will need the wan-tools package which is available from
	  <ftp://ftp.sangoma.com/>. For more information read:
	  <file:Documentation/networking/wan-router.txt>.

	  Note that the answer to this question won't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the questions about WAN router drivers.

	  If unsure, say N.

config CYCLADES_SYNC
	tristate "Cyclom 2X(tm) cards (EXPERIMENTAL)"
	depends on WAN_ROUTER_DRIVERS && (PCI || ISA)
	---help---
	  Cyclom 2X from Cyclades Corporation <http://www.cyclades.com/> is an
	  intelligent multiprotocol WAN adapter with data transfer rates up to
	  512 Kbps. These cards support the X.25 and SNA related protocols.

	  While no documentation is available at this time please grab the
	  wanconfig tarball in
	  <http://www.conectiva.com.br/~acme/cycsyn-devel/> (with minor changes
	  to make it compile with the current wanrouter include files; efforts
	  are being made to use the original package available at
	  <ftp://ftp.sangoma.com/>).

	  Feel free to contact me or the cycsyn-devel mailing list at
	  <[e-mail]> and <[e-mail]> for
	  additional details, I hope to have documentation available as soon as
	  possible. (Cyclades Brazil is writing the Documentation).

	  The next questions will ask you about the protocols you want the
	  driver to support (for now only X.25 is supported).

	  If you have one or more of these cards, say Y to this option.

	  To compile this driver as a module, choose M here: the
	  module will be called cyclomx.

config CYCLOMX_X25
	bool "Cyclom 2X X.25 support (EXPERIMENTAL)"
	depends on CYCLADES_SYNC
	help
	  Connect a Cyclom 2X card to an X.25 network.

	  Enabling X.25 support will enlarge your kernel by about 11 kB.

# X.25 network drivers
config LAPBETHER
	tristate "LAPB over Ethernet driver (EXPERIMENTAL)"
	depends on WAN && LAPB && X25
	---help---
	  Driver for a pseudo device (typically called /dev/lapb0) which allows
	  you to open an LAPB point-to-point connection to some other computer
	  on your Ethernet network.

	  In order to do this, you need to say Y or M to the driver for your
	  Ethernet card as well as to "LAPB Data Link Driver".

	  To compile this driver as a module, choose M here: the
	  module will be called lapbether.

	  If unsure, say N.

config X25_ASY
	tristate "X.25 async driver (EXPERIMENTAL)"
	depends on WAN && LAPB && X25
	---help---
	  Send and receive X.25 frames over regular asynchronous serial
	  lines such as telephone lines equipped with ordinary modems.

	  Experts should note that this driver doesn't currently comply with
	  the asynchronous HDLS framing protocols in CCITT recommendation X.25.

	  To compile this driver as a module, choose M here: the
	  module will be called x25_asy.

	  If unsure, say N.

config SBNI
	tristate "Granch SBNI12 Leased Line adapter support"
	depends on WAN && X86
	---help---
	  Driver for ISA SBNI12-xx cards which are low cost alternatives to
	  leased line modems.

	  You can find more information and last versions of drivers and
	  utilities at <http://www.granch.ru/>. If you have any question you
	  can send email to <[e-mail]>.

	  To compile this driver as a module, choose M here: the
	  module will be called sbni.

	  If unsure, say N.

config SBNI_MULTILINE
	bool "Multiple line feature support"
	depends on SBNI
	help
	  Schedule traffic for some parallel lines, via SBNI12 adapters.

	  If you have two computers connected with two parallel lines it's
	  possible to increase transfer rate nearly twice. You should have
	  a program named 'sbniconfig' to configure adapters.

	  If unsure, say N.

endmenu