philips.txt

LINUX 2.6.17.4的源码

This file contains some additional information for the Philips and OEM webcams.
E-mail: [e-mail]                        Last updated: 2004-01-19
Site: http://www.smcc.demon.nl/webcam/

As of this moment, the following cameras are supported:
 * Philips PCA645
 * Philips PCA646
 * Philips PCVC675
 * Philips PCVC680
 * Philips PCVC690
 * Philips PCVC720/40
 * Philips PCVC730
 * Philips PCVC740
 * Philips PCVC750
 * Askey VC010
 * Creative Labs Webcam 5
 * Creative Labs Webcam Pro Ex
 * Logitech QuickCam 3000 Pro
 * Logitech QuickCam 4000 Pro
 * Logitech QuickCam Notebook Pro
 * Logitech QuickCam Zoom
 * Logitech QuickCam Orbit
 * Logitech QuickCam Sphere
 * Samsung MPC-C10
 * Samsung MPC-C30
 * Sotec Afina Eye
 * AME CU-001
 * Visionite VCS-UM100
 * Visionite VCS-UC300

The main webpage for the Philips driver is at the address above. It contains
a lot of extra information, a FAQ, and the binary plugin 'PWCX'. This plugin
contains decompression routines that allow you to use higher image sizes and
framerates; in addition the webcam uses less bandwidth on the USB bus (handy
if you want to run more than 1 camera simultaneously). These routines fall
under a NDA, and may therefor not be distributed as source; however, its use
is completely optional.

You can build this code either into your kernel, or as a module. I recommend
the latter, since it makes troubleshooting a lot easier. The built-in
microphone is supported through the USB Audio class.

When you load the module you can set some default settings for the
camera; some programs depend on a particular image-size or -format and
don't know how to set it properly in the driver. The options are:

size
   Can be one of 'sqcif', 'qsif', 'qcif', 'sif', 'cif' or
   'vga', for an image size of resp. 128x96, 160x120, 176x144,
   320x240, 352x288 and 640x480 (of course, only for those cameras that
   support these resolutions).

fps
   Specifies the desired framerate. Is an integer in the range of 4-30.

fbufs
   This paramter specifies the number of internal buffers to use for storing
   frames from the cam. This will help if the process that reads images from
   the cam is a bit slow or momentarely busy. However, on slow machines it
   only introduces lag, so choose carefully. The default is 3, which is
   reasonable. You can set it between 2 and 5.

mbufs
   This is an integer between 1 and 10. It will tell the module the number of
   buffers to reserve for mmap(), VIDIOCCGMBUF, VIDIOCMCAPTURE and friends.
   The default is 2, which is adequate for most applications (double
   buffering).

   Should you experience a lot of 'Dumping frame...' messages during
   grabbing with a tool that uses mmap(), you might want to increase if.
   However, it doesn't really buffer images, it just gives you a bit more
   slack when your program is behind. But you need a multi-threaded or
   forked program to really take advantage of these buffers.

   The absolute maximum is 10, but don't set it too high!  Every buffer takes
   up 460 KB of RAM, so unless you have a lot of memory setting this to
   something more than 4 is an absolute waste.  This memory is only
   allocated during open(), so nothing is wasted when the camera is not in
   use.

power_save
   When power_save is enabled (set to 1), the module will try to shut down
   the cam on close() and re-activate on open(). This will save power and
   turn off the LED. Not all cameras support this though (the 645 and 646
   don't have power saving at all), and some models don't work either (they
   will shut down, but never wake up). Consider this experimental. By
   default this option is disabled.

compression (only useful with the plugin)
   With this option you can control the compression factor that the camera
   uses to squeeze the image through the USB bus. You can set the
   parameter between 0 and 3:
     0 = prefer uncompressed images; if the requested mode is not available
	 in an uncompressed format, the driver will silently switch to low
	 compression.
     1 = low compression.
     2 = medium compression.
     3 = high compression.

   High compression takes less bandwidth of course, but it could also
   introduce some unwanted artefacts. The default is 2, medium compression.
   See the FAQ on the website for an overview of which modes require
   compression.

   The compression parameter does not apply to the 645 and 646 cameras
   and OEM models derived from those (only a few). Most cams honour this
   parameter.

leds
   This settings takes 2 integers, that define the on/off time for the LED
   (in milliseconds). One of the interesting things that you can do with
   this is let the LED blink while the camera is in use. This:

     leds=500,500

   will blink the LED once every second. But with:

     leds=0,0

   the LED never goes on, making it suitable for silent surveillance.

   By default the camera's LED is on solid while in use, and turned off
   when the camera is not used anymore.

   This parameter works only with the ToUCam range of cameras (720, 730, 740,
   750) and OEMs. For other cameras this command is silently ignored, and
   the LED cannot be controlled.

   Finally: this parameters does not take effect UNTIL the first time you
   open the camera device. Until then, the LED remains on.

dev_hint
   A long standing problem with USB devices is their dynamic nature: you
   never know what device a camera gets assigned; it depends on module load
   order, the hub configuration, the order in which devices are plugged in,
   and the phase of the moon (i.e. it can be random). With this option you
   can give the driver a hint as to what video device node (/dev/videoX) it
   should use with a specific camera. This is also handy if you have two
   cameras of the same model.

   A camera is specified by its type (the number from the camera model,
   like PCA645, PCVC750VC, etc) and optionally the serial number (visible
   in /proc/bus/usb/devices). A hint consists of a string with the following
   format:

      [type[.serialnumber]:]node

   The square brackets mean that both the type and the serialnumber are
   optional, but a serialnumber cannot be specified without a type (which
   would be rather pointless). The serialnumber is separated from the type
   by a '.'; the node number by a ':'.

   This somewhat cryptic syntax is best explained by a few examples:

     dev_hint=3,5              The first detected cam gets assigned
			       /dev/video3, the second /dev/video5. Any
			       other cameras will get the first free
			       available slot (see below).

     dev_hint=645:1,680:2      The PCA645 camera will get /dev/video1,
			       and a PCVC680 /dev/video2.

     dev_hint=645.0123:3,645.4567:0	The PCA645 camera with serialnumber
					0123 goes to /dev/video3, the same
					camera model with the 4567 serial
					gets /dev/video0.

     dev_hint=750:1,4,5,6       The PCVC750 camera will get /dev/video1, the
				next 3 Philips cams will use /dev/video4
				through /dev/video6.

   Some points worth knowing:
   - Serialnumbers are case sensitive and must be written full, including
     leading zeroes (it's treated as a string).
   - If a device node is already occupied, registration will fail and
     the webcam is not available.
   - You can have up to 64 video devices; be sure to make enough device
     nodes in /dev if you want to spread the numbers (this does not apply
     to devfs). After /dev/video9 comes /dev/video10 (not /dev/videoA).
   - If a camera does not match any dev_hint, it will simply get assigned
     the first available device node, just as it used to be.

trace
   In order to better detect problems, it is now possible to turn on a
   'trace' of some of the calls the module makes; it logs all items in your
   kernel log at debug level.

   The trace variable is a bitmask; each bit represents a certain feature.
   If you want to trace something, look up the bit value(s) in the table
   below, add the values together and supply that to the trace variable.

   Value  Value   Description					   Default
   (dec)  (hex)
       1    0x1   Module initialization; this will log messages       On
		  while loading and unloading the module

       2    0x2   probe() and disconnect() traces                     On

       4    0x4   Trace open() and close() calls                      Off

       8    0x8   read(), mmap() and associated ioctl() calls         Off

      16   0x10   Memory allocation of buffers, etc.                  Off

      32   0x20   Showing underflow, overflow and Dumping frame       On
		  messages

      64   0x40   Show viewport and image sizes                       Off

     128   0x80   PWCX debugging                                      Off

   For example, to trace the open() & read() fuctions, sum 8 + 4 = 12,
   so you would supply trace=12 during insmod or modprobe. If
   you want to turn the initialization and probing tracing off, set trace=0.
   The default value for trace is 35 (0x23).



Example:

     # modprobe pwc size=cif fps=15 power_save=1

The fbufs, mbufs and trace parameters are global and apply to all connected
cameras. Each camera has its own set of buffers.

size and fps only specify defaults when you open() the device; this is to
accommodate some tools that don't set the size. You can change these
settings after open() with the Video4Linux ioctl() calls. The default of
defaults is QCIF size at 10 fps.

The compression parameter is semiglobal; it sets the initial compression
preference for all camera's, but this parameter can be set per camera with
the VIDIOCPWCSCQUAL ioctl() call.

All parameters are optional.