e1000_ethtool.c

e1000 8.0.1 version.最新的e1000 linux下的驱动

	/* Disable all the interrupts */
	E1000_WRITE_REG(&adapter->hw, E1000_IMC, 0xFFFFFFFF);
	msleep(10);

	/* Unhook test interrupt handler */
	free_irq(irq, netdev);

	return *data;
}

static void e1000_free_desc_rings(struct e1000_adapter *adapter)
{
	struct e1000_tx_ring *tx_ring = &adapter->test_tx_ring;
	struct e1000_rx_ring *rx_ring = &adapter->test_rx_ring;
	struct pci_dev *pdev = adapter->pdev;
	int i;

	if (tx_ring->desc && tx_ring->buffer_info) {
		for (i = 0; i < tx_ring->count; i++) {
			if (tx_ring->buffer_info[i].dma)
				pci_unmap_single(pdev, tx_ring->buffer_info[i].dma,
						 tx_ring->buffer_info[i].length,
						 PCI_DMA_TODEVICE);
			if (tx_ring->buffer_info[i].skb)
				dev_kfree_skb(tx_ring->buffer_info[i].skb);
		}
	}

	if (rx_ring->desc && rx_ring->buffer_info) {
		for (i = 0; i < rx_ring->count; i++) {
			if (rx_ring->buffer_info[i].dma)
				pci_unmap_single(pdev, rx_ring->buffer_info[i].dma,
						 E1000_RXBUFFER_2048,
						 PCI_DMA_FROMDEVICE);
			if (rx_ring->buffer_info[i].skb)
				dev_kfree_skb(rx_ring->buffer_info[i].skb);
		}
	}

	if (tx_ring->desc) {
		pci_free_consistent(pdev, tx_ring->size, tx_ring->desc, tx_ring->dma);
		tx_ring->desc = NULL;
	}
	if (rx_ring->desc) {
		pci_free_consistent(pdev, rx_ring->size, rx_ring->desc, rx_ring->dma);
		rx_ring->desc = NULL;
	}

	kfree(tx_ring->buffer_info);
	tx_ring->buffer_info = NULL;
	kfree(rx_ring->buffer_info);
	rx_ring->buffer_info = NULL;

	return;
}

static int e1000_setup_desc_rings(struct e1000_adapter *adapter)
{
	struct e1000_tx_ring *tx_ring = &adapter->test_tx_ring;
	struct e1000_rx_ring *rx_ring = &adapter->test_rx_ring;
	struct pci_dev *pdev = adapter->pdev;
	u32 rctl;
	int i, ret_val;

	/* Setup Tx descriptor ring and Tx buffers */

	if (!tx_ring->count)
		tx_ring->count = E1000_DEFAULT_TXD;

	if (!(tx_ring->buffer_info = kcalloc(tx_ring->count,
	                                     sizeof(struct e1000_buffer),
	                                     GFP_KERNEL))) {
		ret_val = 1;
		goto err_nomem;
	}

	tx_ring->size = tx_ring->count * sizeof(struct e1000_tx_desc);
	tx_ring->size = ALIGN(tx_ring->size, 4096);
	if (!(tx_ring->desc = pci_alloc_consistent(pdev, tx_ring->size,
	                                           &tx_ring->dma))) {
		ret_val = 2;
		goto err_nomem;
	}
	tx_ring->next_to_use = tx_ring->next_to_clean = 0;

	E1000_WRITE_REG(&adapter->hw, E1000_TDBAL(0),
			((u64) tx_ring->dma & 0x00000000FFFFFFFF));
	E1000_WRITE_REG(&adapter->hw, E1000_TDBAH(0), ((u64) tx_ring->dma >> 32));
	E1000_WRITE_REG(&adapter->hw, E1000_TDLEN(0),
			tx_ring->count * sizeof(struct e1000_tx_desc));
	E1000_WRITE_REG(&adapter->hw, E1000_TDH(0), 0);
	E1000_WRITE_REG(&adapter->hw, E1000_TDT(0), 0);
	E1000_WRITE_REG(&adapter->hw, E1000_TCTL,
			E1000_TCTL_MULR |
			E1000_TCTL_PSP | E1000_TCTL_EN |
			E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT |
			E1000_COLLISION_DISTANCE << E1000_COLD_SHIFT);

	for (i = 0; i < tx_ring->count; i++) {
		struct e1000_tx_desc *tx_desc = E1000_TX_DESC(*tx_ring, i);
		struct sk_buff *skb;
		unsigned int size = 1024;

		if (!(skb = alloc_skb(size, GFP_KERNEL))) {
			ret_val = 3;
			goto err_nomem;
		}
		skb_put(skb, size);
		tx_ring->buffer_info[i].skb = skb;
		tx_ring->buffer_info[i].length = skb->len;
		tx_ring->buffer_info[i].dma =
			pci_map_single(pdev, skb->data, skb->len,
				       PCI_DMA_TODEVICE);
		tx_desc->buffer_addr = cpu_to_le64(tx_ring->buffer_info[i].dma);
		tx_desc->lower.data = cpu_to_le32(skb->len);
		tx_desc->lower.data |= cpu_to_le32(E1000_TXD_CMD_EOP |
						   E1000_TXD_CMD_IFCS);
		if (adapter->hw.mac.type < e1000_82543)
			tx_desc->lower.data |= E1000_TXD_CMD_RPS;
		else
			tx_desc->lower.data |= E1000_TXD_CMD_RS;

		tx_desc->upper.data = 0;
	}

	/* Setup Rx descriptor ring and Rx buffers */

	if (!rx_ring->count)
		rx_ring->count = E1000_DEFAULT_RXD;

	if (!(rx_ring->buffer_info = kcalloc(rx_ring->count,
	                                     sizeof(struct e1000_rx_buffer),
	                                     GFP_KERNEL))) {
		ret_val = 4;
		goto err_nomem;
	}

	rx_ring->size = rx_ring->count * sizeof(struct e1000_rx_desc);
	if (!(rx_ring->desc = pci_alloc_consistent(pdev, rx_ring->size,
	                                           &rx_ring->dma))) {
		ret_val = 5;
		goto err_nomem;
	}
	rx_ring->next_to_use = rx_ring->next_to_clean = 0;

	rctl = E1000_READ_REG(&adapter->hw, E1000_RCTL);
	E1000_WRITE_REG(&adapter->hw, E1000_RCTL, rctl & ~E1000_RCTL_EN);
	E1000_WRITE_REG(&adapter->hw, E1000_RDBAL(0),
			((u64) rx_ring->dma & 0xFFFFFFFF));
	E1000_WRITE_REG(&adapter->hw, E1000_RDBAH(0), ((u64) rx_ring->dma >> 32));
	E1000_WRITE_REG(&adapter->hw, E1000_RDLEN(0), rx_ring->size);
	E1000_WRITE_REG(&adapter->hw, E1000_RDH(0), 0);
	E1000_WRITE_REG(&adapter->hw, E1000_RDT(0), 0);
	rctl = E1000_RCTL_EN | E1000_RCTL_BAM | E1000_RCTL_SZ_2048 |
		E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF |
		(adapter->hw.mac.mc_filter_type << E1000_RCTL_MO_SHIFT);
	E1000_WRITE_REG(&adapter->hw, E1000_RCTL, rctl);

	for (i = 0; i < rx_ring->count; i++) {
		struct e1000_rx_desc *rx_desc = E1000_RX_DESC(*rx_ring, i);
		struct sk_buff *skb;

		if (!(skb = alloc_skb(E1000_RXBUFFER_2048 + NET_IP_ALIGN,
				GFP_KERNEL))) {
			ret_val = 6;
			goto err_nomem;
		}
		skb_reserve(skb, NET_IP_ALIGN);
		rx_ring->buffer_info[i].skb = skb;
		rx_ring->buffer_info[i].dma =
			pci_map_single(pdev, skb->data, E1000_RXBUFFER_2048,
				       PCI_DMA_FROMDEVICE);
		rx_desc->buffer_addr = cpu_to_le64(rx_ring->buffer_info[i].dma);
		memset(skb->data, 0x00, skb->len);
	}

	return 0;

err_nomem:
	e1000_free_desc_rings(adapter);
	return ret_val;
}

static void e1000_phy_disable_receiver(struct e1000_adapter *adapter)
{
	/* Write out to PHY registers 29 and 30 to disable the Receiver. */
	e1000_write_phy_reg(&adapter->hw, 29, 0x001F);
	e1000_write_phy_reg(&adapter->hw, 30, 0x8FFC);
	e1000_write_phy_reg(&adapter->hw, 29, 0x001A);
	e1000_write_phy_reg(&adapter->hw, 30, 0x8FF0);
}

static void e1000_phy_reset_clk_and_crs(struct e1000_adapter *adapter)
{
	u16 phy_reg;

	/* Because we reset the PHY above, we need to re-force TX_CLK in the
	 * Extended PHY Specific Control Register to 25MHz clock.  This
	 * value defaults back to a 2.5MHz clock when the PHY is reset.
	 */
	e1000_read_phy_reg(&adapter->hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_reg);
	phy_reg |= M88E1000_EPSCR_TX_CLK_25;
	e1000_write_phy_reg(&adapter->hw,
		M88E1000_EXT_PHY_SPEC_CTRL, phy_reg);

	/* In addition, because of the s/w reset above, we need to enable
	 * CRS on TX.  This must be set for both full and half duplex
	 * operation.
	 */
	e1000_read_phy_reg(&adapter->hw, M88E1000_PHY_SPEC_CTRL, &phy_reg);
	phy_reg |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
	e1000_write_phy_reg(&adapter->hw,
		M88E1000_PHY_SPEC_CTRL, phy_reg);
}

static int e1000_nonintegrated_phy_loopback(struct e1000_adapter *adapter)
{
	u32 ctrl_reg;
	u16 phy_reg;

	/* Setup the Device Control Register for PHY loopback test. */

	ctrl_reg = E1000_READ_REG(&adapter->hw, E1000_CTRL);
	ctrl_reg |= (E1000_CTRL_ILOS |		/* Invert Loss-Of-Signal */
		     E1000_CTRL_FRCSPD |	/* Set the Force Speed Bit */
		     E1000_CTRL_FRCDPX |	/* Set the Force Duplex Bit */
		     E1000_CTRL_SPD_1000 |	/* Force Speed to 1000 */
		     E1000_CTRL_FD);		/* Force Duplex to FULL */

	E1000_WRITE_REG(&adapter->hw, E1000_CTRL, ctrl_reg);

	/* Read the PHY Specific Control Register (0x10) */
	e1000_read_phy_reg(&adapter->hw, M88E1000_PHY_SPEC_CTRL, &phy_reg);

	/* Clear Auto-Crossover bits in PHY Specific Control Register
	 * (bits 6:5).
	 */
	phy_reg &= ~M88E1000_PSCR_AUTO_X_MODE;
	e1000_write_phy_reg(&adapter->hw, M88E1000_PHY_SPEC_CTRL, phy_reg);

	/* Perform software reset on the PHY */
	e1000_phy_commit(&adapter->hw);

	/* Have to setup TX_CLK and TX_CRS after software reset */
	e1000_phy_reset_clk_and_crs(adapter);

	e1000_write_phy_reg(&adapter->hw, PHY_CONTROL, 0x8100);

	/* Wait for reset to complete. */
	udelay(500);

	/* Have to setup TX_CLK and TX_CRS after software reset */
	e1000_phy_reset_clk_and_crs(adapter);

	/* Write out to PHY registers 29 and 30 to disable the Receiver. */
	e1000_phy_disable_receiver(adapter);

	/* Set the loopback bit in the PHY control register. */
	e1000_read_phy_reg(&adapter->hw, PHY_CONTROL, &phy_reg);
	phy_reg |= MII_CR_LOOPBACK;
	e1000_write_phy_reg(&adapter->hw, PHY_CONTROL, phy_reg);

	/* Setup TX_CLK and TX_CRS one more time. */
	e1000_phy_reset_clk_and_crs(adapter);

	/* Check Phy Configuration */
	e1000_read_phy_reg(&adapter->hw, PHY_CONTROL, &phy_reg);
	if (phy_reg != 0x4100)
		 return 9;

	e1000_read_phy_reg(&adapter->hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_reg);
	if (phy_reg != 0x0070)
		return 10;

	e1000_read_phy_reg(&adapter->hw, 29, &phy_reg);
	if (phy_reg != 0x001A)
		return 11;

	return 0;
}

static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
{
	u32 ctrl_reg = 0;
	u32 stat_reg = 0;

	adapter->hw.mac.autoneg = FALSE;

	if (adapter->hw.phy.type == e1000_phy_m88) {
		/* Auto-MDI/MDIX Off */
		e1000_write_phy_reg(&adapter->hw,
				    M88E1000_PHY_SPEC_CTRL, 0x0808);
		/* reset to update Auto-MDI/MDIX */
		e1000_write_phy_reg(&adapter->hw, PHY_CONTROL, 0x9140);
		/* autoneg off */
		e1000_write_phy_reg(&adapter->hw, PHY_CONTROL, 0x8140);
	} else if (adapter->hw.phy.type == e1000_phy_gg82563)
		e1000_write_phy_reg(&adapter->hw,
		                    GG82563_PHY_KMRN_MODE_CTRL,
		                    0x1CC);

	ctrl_reg = E1000_READ_REG(&adapter->hw, E1000_CTRL);

	if (adapter->hw.phy.type == e1000_phy_ife) {
		/* force 100, set loopback */
		e1000_write_phy_reg(&adapter->hw, PHY_CONTROL, 0x6100);

		/* Now set up the MAC to the same speed/duplex as the PHY. */
		ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */
		ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */
			     E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */
			     E1000_CTRL_SPD_100 |/* Force Speed to 100 */
			     E1000_CTRL_FD);	 /* Force Duplex to FULL */
	} else {
		/* force 1000, set loopback */
		e1000_write_phy_reg(&adapter->hw, PHY_CONTROL, 0x4140);

		/* Now set up the MAC to the same speed/duplex as the PHY. */
		ctrl_reg = E1000_READ_REG(&adapter->hw, E1000_CTRL);
		ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */
		ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */
			     E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */
			     E1000_CTRL_SPD_1000 |/* Force Speed to 1000 */
			     E1000_CTRL_FD);	 /* Force Duplex to FULL */
	}

	if (adapter->hw.phy.media_type == e1000_media_type_copper &&
	   adapter->hw.phy.type == e1000_phy_m88) {
		ctrl_reg |= E1000_CTRL_ILOS; /* Invert Loss of Signal */
	} else {
		/* Set the ILOS bit on the fiber Nic if half duplex link is
		 * detected. */
		stat_reg = E1000_READ_REG(&adapter->hw, E1000_STATUS);
		if ((stat_reg & E1000_STATUS_FD) == 0)
			ctrl_reg |= (E1000_CTRL_ILOS | E1000_CTRL_SLU);
	}

	E1000_WRITE_REG(&adapter->hw, E1000_CTRL, ctrl_reg);

	/* Disable the receiver on the PHY so when a cable is plugged in, the
	 * PHY does not begin to autoneg when a cable is reconnected to the NIC.
	 */
	if (adapter->hw.phy.type == e1000_phy_m88)
		e1000_phy_disable_receiver(adapter);

	udelay(500);

	return 0;
}

static int e1000_set_phy_loopback(struct e1000_adapter *adapter)
{
	u16 phy_reg = 0;
	u16 count = 0;

	switch (adapter->hw.mac.type) {
	case e1000_82543:
		if (adapter->hw.phy.media_type == e1000_media_type_copper) {
			/* Attempt to setup Loopback mode on Non-integrated PHY.
			 * Some PHY registers get corrupted at random, so
			 * attempt this 10 times.
			 */
			while (e1000_nonintegrated_phy_loopback(adapter) &&
			      count++ < 10);
			if (count < 11)
				return 0;
		}
		break;

	case e1000_82544:
	case e1000_82540:
	case e1000_82545:
	case e1000_82545_rev_3:
	case e1000_82546:
	case e1000_82546_rev_3:
	case e1000_82541:
	case e1000_82541_rev_2:
	case e1000_82547:
	case e1000_82547_rev_2:
		return e1000_integrated_phy_loopback(adapter);
		break;

	default:
		/* Default PHY loopback work is to read the MII
		 * control register and assert bit 14 (loopback mode).
		 */
		e1000_read_phy_reg(&adapter->hw, PHY_CONTROL, &phy_reg);
		phy_reg |= MII_CR_LOOPBACK;
		e1000_write_phy_reg(&adapter->hw, PHY_CONTROL, phy_reg);
		return 0;
		break;
	}

	return 8;
}

static int e1000_setup_loopback_test(struct e1000_adapter *adapter)
{
	struct e1000_hw *hw = &adapter->hw;
	u32 rctl;

	if (hw->phy.media_type == e1000_media_type_fiber ||
	    hw->phy.media_type == e1000_media_type_internal_serdes) {
		switch (hw->mac.type) {
		case e1000_82545:
		case e1000_82546:
		case e1000_82545_rev_3:
		case e1000_82546_rev_3:
			return e1000_set_phy_loopback(adapter);
			break;
		default:
			rctl = E1000_READ_REG(hw, E1000_RCTL);
			rctl |= E1000_RCTL_LBM_TCVR;
			E1000_WRITE_REG(hw, E1000_RCTL, rctl);
			return 0;
		}
	} else if (hw->phy.media_type == e1000_media_type_copper)
		return e1000_set_phy_loopback(adapter);

	return 7;
}

static void e1000_loopback_cleanup(struct e1000_adapter *adapter)
{
	struct e1000_hw *hw = &adapter->hw;
	u32 rctl;
	u16 phy_reg;

	rctl = E1000_READ_REG(hw, E1000_RCTL);
	rctl &= ~(E1000_RCTL_LBM_TCVR | E1000_RCTL_LBM_MAC);
	E1000_WRITE_REG(hw, E1000_RCTL, rctl);

	hw->mac.autoneg = TRUE;
	if (hw->phy.type == e1000_phy_gg82563)
		e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, 0x180);
	e1000_read_phy_reg(hw, PHY_CONTROL, &phy_reg);
	if (phy_reg & MII_CR_LOOPBACK) {
		phy_reg &= ~MII_CR_LOOPBACK;
		e1000_write_phy_reg(hw, PHY_CONTROL, phy_reg);
		e1000_phy_commit(hw);
	}
}

static void e1000_create_lbtest_frame(struct sk_buff *skb,
                                      unsigned int frame_size)
{
	memset(skb->data, 0xFF, frame_size);
	frame_size &= ~1;
	memset(&skb->data[frame_size / 2], 0xAA, frame_size / 2 - 1);
	memset(&skb->data[frame_size / 2 + 10], 0xBE, 1);
	memset(&skb->data[frame_size / 2 + 12], 0xAF, 1);
}

static int e1000_check_lbtest_frame(struct sk_buff *skb, unsigned int frame_size)
{
	frame_size &= ~1;
	if (*(skb->data + 3) == 0xFF) {
		if ((*(skb->data + frame_size / 2 + 10) == 0xBE) &&
		   (*(skb->data + frame_size / 2 + 12) == 0xAF)) {
			return 0;
		}
	}
	return 13;
}

static int e1000_run_loopback_test(struct e1000_adapter *adapter)
{
	struct e1000_tx_ring *tx_ring = &adapter->test_tx_ring;
	struct e1000_rx_ring *rx_ring = &adapter->test_rx_ring;
	struct pci_dev *pdev = adapter->pdev;
	int i, j, k, l, lc, good_cnt, ret_val=0;
	unsigned long time;

	E1000_WRITE_REG(&adapter->hw, E1000_RDT(0), rx_ring->count - 1);

	/* Calculate the loop count based on the largest descriptor ring
	 * The idea is to wrap the largest ring a number of times using 64
	 * send/receive pairs during each loop
	 */

	if (rx_ring->count <= tx_ring->count)
		lc = ((tx_ring->count / 64) * 2) + 1;
	else
		lc = ((rx_ring->count / 64) * 2) + 1;

	k = l = 0;
	for (j = 0; j <= lc; j++) { /* loop count loop */
		for (i = 0; i < 64; i++) { /* send the packets */
			e1000_create_lbtest_frame(tx_ring->buffer_info[k].skb,
					1024);
			pci_dma_sync_single_for_device(pdev,