het_int_02.c

tmp470开发板的源程序

//*****************************************************************************
//  TMS470 Demo -  HET Interrupt Sample Program
//
//  Program name : HET_INT_02.c associated with HET program HET_INT_02_H.het
//
//  Description; This program uses the HET to trigger the ADC at 10 ms
//  intervals when used with a 12 MHz clock. The result of the ADC is
//  averaged 20 times and the result is displayed using the LEDs on the A256 EVM.
//
//  *An external 12Mhz XTAL on OSCIN OSCOUT with proper load caps required*
//
//              TMS-FET470A256
//             -----------------
//         /|\|            OSCIN|-
//          | |                 | 12MHz
//          --|PLLDIS     OSCOUT|-
//            |                 |
//        >---|ADIN0         HET|---> 10 LEDs
//            |                 |
//
//  John Mangino / Lane Westlund
//  Texas Instruments, Inc
//  May 2005
//  Built with IAR Embedded Workbench Version: 4.20A
//  A256 EVM
//******************************************************************************

#include <intrinsic.h>
#include "iotms470r1a256.h"
#include "tms470r1a256_bit_definitions.h"
#include "std_het.h"
#include "HET_INT_02_H.h"

void MemCopy32(unsigned long *dst, unsigned long *src, int bytes);

__no_init volatile HETPROGRAM0_UN e_HETPROGRAM0_UN @ 0x00800000;

unsigned int result[20];
unsigned int average;

void main(void)
{
 // Set up peripheral registers.

  PCR = CLKDIV_1;                         // ICLK = SYSCLK
  PCR |= PENABLE;                         // enable peripherals

  REQMASK = 0;                            // clear interrupt mask
  REQMASK |= (1<<CIM_MIBADCE1);           // enable channel 27 (AD1)

  ADCR1 |= PS_8;                          // ADCLK prescaler = 8
  ADSAMPEV |= SEN;                        // ADCSAMP1 controls SW
  ADSAMP1 = 62;                           // SW = 62+2

  ADCR1 |= ADC_EN;                        // Enable ADC
  ADISR1 = 0x0001;                        // group 1 = channel 0

  ADEVTSRC = G1_SRC_INT1 + G1_EDG_SEL + G1_ENA; // enable group 1 and set trigger for low
                                                // to high transition
  ADBCR1 |= BUF_EN;                       // enable buffered mode
  ADBCR1 |= BNDA_8;                       // set RAM boundary between event and group 1
                                          // units of two words from the beginning of buffer
                                          // event group has 8*2 = 16 words for the FIFO
  ADBCR1 |= BNDB_16 + BNDB_2;             // set RAM boundary between group 1 and 2
                                          // units of two words from the beginning of buffer
                                          // group 1 has (18-8)*2 = 20 words for the FIFO
  ADBCR2 |= BNDEND_64;                    // set RAM buffer end boundary
                                          // 64-word FIFO buffer
                                          // group 2 has 64-(2*18) = 28 words for the FIFO

  ADTHRG1 = G1THR_16 + G1THR_4;           // group 1 threshold counter = 20, 20 results will be
                                          // placed on the buffer before setting G1 BUF INT FLAG

  ADBUFST &= ~G1_INT_FLAG;                // clear flag
  ADBCR3 |= G1_OVR_INT_EN;                // enable group 1 FIFO buffer over-run interrupt
  ADBCR3 |= G1_BUF_INT_EN;                // enable group 1 FIFO buffer interrupt

  HETGCR = CLK_MASTER + IGNORE_SUSPEND;   //  HET Master Mode, Ignore SW BP

  // copy HET instructions to HET ram

  MemCopy32((void *) &e_HETPROGRAM0_UN, (void *) HET_INIT0_PST, sizeof(HET_INIT0_PST));

  HETPFR  = 0x00000309;                   // Set PFR register	/8 /10
  HETDIR  = 0xFFFFFFFF;                   // Set all HET as GIO outputs
  HETDOUT = 0xFFFFFFFF;                   // Flash all leds off and on and off
  HETGCR |= ON;                           // Start HET

  __enable_interrupt();                   // enable interrupts

  // Loop forever.
  while(1){}
}

//------------------------------------------------------------------------------
// This module programms the HET RAM with the HET code
//------------------------------------------------------------------------------
 void MemCopy32(unsigned long *dst, unsigned long *src, int bytes)
{
  for (int i = 0; i < (bytes + 3) / 4; i++)
    *dst++ = *src++;
}

//------------------------------------------------------------------------------
// Display data on the LEDs
//------------------------------------------------------------------------------

void LedSet(unsigned int mask)
{
unsigned int out = 0;
  mask ^= 0xFFFFFFFF;

  out |= (mask << 16)& 0x80000000;
  out |= (mask << 10)& 0x01000000;
  out |= (mask << 8) & 0x003c0000;
  out |= (mask << 4) & 0x00003c00;
  out |= (mask << 3) & 0x000001c0;
  out |= (mask << 2) & 0x00000010;
  out |= (mask << 1) & 0x00000004;
  out |=  mask       & 0x00000001;
  HETDOUT = out;
  }

//------------------------------------------------------------------------------
// TMS470R1A256 Standard Interrupt Handler
//------------------------------------------------------------------------------
#pragma vector = IRQV
__irq __arm void irq_handler(void)
{
   switch((0xff & IRQIVEC)-1)
  {
   case CIM_MIBADCE1  :                      // channel 27 (AD1) interrupt?
   if (ADBUFST & 0x0020)                     // buffer over-run?
     {
       ADISR1 = 0x0001;                      // clear buffer
       ADTHRG1 = G1THR_16 + G1THR_4;         // reset group 1 threshold
     }
     else
     {
       unsigned int i;
       ADBUFST &= ~G1_INT_FLAG;               // clear flag
       average = 0;
       for (i=0; i<20; i++)
       {
         result[i] = ADBUF1;                  // read FIFO value
         average = average + result[i];       // sum values
       }
       average = (unsigned int) average / 20;  // get average
       LedSet(average);
      }
      break;
  }
}