example_280xi2c_eeprom.c

来自「DSP2808例程。TMS320F2808DSP的各个模块的应用例程」· C语言 代码 · 共 687 行 · 第 1/2 页

// TI File $Revision: /main/3 $
// Checkin $Date: December 3, 2004   13:40:48 $
//###########################################################################
//
// FILE:    Example_280xI2c_eeprom.c
//
// TITLE:   DSP280x I2C EEPROM Example
//
// ASSUMPTIONS:
//
//    This program requires the DSP280x header files.  
//
//    This program requires an external I2C EEPROM connected to
//    the I2C bus at address 0x50. 
//
//    As supplied, this project is configured for "boot to SARAM" 
//    operation.  The 280x Boot Mode table is shown below.  
//    For information on configuring the boot mode of an eZdsp, 
//    please refer to the documentation included with the eZdsp,  
//
//       Boot      GPIO18     GPIO29    GPIO34
//       Mode      SPICLKA    SCITXDA
//                  SCITXB
//       -------------------------------------
//       Flash       1          1        1
//       SCI-A       1          1        0
//       SPI-A       1          0        1
//       I2C-A       1          0        0
//       ECAN-A      0          1        1        
//       SARAM       0          1        0  <- "boot to SARAM"
//       OTP         0          0        1
//       I/0         0          0        0 
//
// DESCRIPTION:
//
//    This program will write 1-14 words to EEPROM and read them back.
//    The data written and the EEPROM address written to are contained
//    in the message structure, I2cMsgOut1. The data read back will be
//    contained in the message structure I2cMsgIn1.
//
//    This program will work with the on-board I2C EEPROM supplied on 
//    the F280x eZdsp.
//
//
//###########################################################################
// Original Author: D.F.
//
// $TI Release: DSP280x V1.30 $
// $Release Date: February 10, 2006 $
//###########################################################################


#include "DSP280x_Device.h"     // DSP280x Headerfile Include File
#include "DSP280x_Examples.h"   // DSP280x Examples Include File
/* 2线接口的位操作,与单片机有关 */
#define		CH452_SCL_SET		GpioDataRegs.GPBSET.bit.GPIO33 = 1//{CH452_SCL=1;}
#define		CH452_SCL_CLR		GpioDataRegs.GPBCLEAR.bit.GPIO33 = 1//{CH452_SCL=0;}
#define		CH452_SDA_SET		GpioDataRegs.GPBSET.bit.GPIO32 = 1//{CH452_SDA=1;}
#define		CH452_SDA_CLR		GpioDataRegs.GPBCLEAR.bit.GPIO32 = 1//{CH452_SDA=0;}
#define		CH452_SDA_IN		GpioDataRegs.GPBDAT.bit.GPIO32//(CH452_SDA)
#define		CH452_SDA_D_OUT		GpioCtrlRegs.GPBDIR.bit.GPIO32 = 1;	// 设置SDA为输出方向,对于双向I/O需切换为输出
#define		CH452_SDA_D_IN		GpioCtrlRegs.GPBDIR.bit.GPIO32 = 0;	//{CH452_SDA=1;}	// 设置SDA为输入方向,对于双向I/O需切换为输入

/* CH451和CH452的常用命令码 */
#define CH452_NOP		0x0000					// 空操作
#define CH452_RESET     0x0201					// 复位
#define CH452_LEVEL		0x0100					// 加载光柱值
#define CH452_CLR_BIT	0x0180					// 段位清0
#define CH452_SET_BIT	0x01C0					// 段位置1
#define CH452_SLEEP		0x0202					// 进入睡眠状态
#define CH452_LEFTMOV   0x0300		            //设置移动方式-作移
#define CH452_LEFTCYC   0x0301		            //设置移动方式-左循
#define CH452_RIGHTMOV  0x0302		            //设置移动方式-右移
#define CH452_RIGHTCYC  0x0303		            //设置移动方式-右循	
#define CH452_SELF_BCD	0x0380					//自定义BCD码
#define CH452_SYSOFF    0x0400					//关显示、键盘
#define CH452_SYSON1    0x0401					//开显示
#define CH452_SYSON2    0x0403					//开显示、键盘
#define CH452_SYSON2W   0x0423					//开显示、键盘, 真正2线接口
#define CH452_DSP       0x0500					//设置默认显示方式
#define CH452_BCD       0x0580					//设置BCD译码方式
#define CH452_TWINKLE   0x0600		            //设置闪烁控制
#define CH452_GET_KEY	0x0700					// 获取按键
#define CH452_DIG0      0x0800					//数码管位0显示
#define CH452_DIG1      0x0900		            //数码管位1显示 
#define CH452_DIG2      0x0a00		            //数码管位2显示
#define CH452_DIG3      0x0b00		            //数码管位3显示
#define CH452_DIG4      0x0c00		            //数码管位4显示
#define CH452_DIG5      0x0d00					//数码管位5显示	
#define CH452_DIG6      0x0e00					//数码管位6显示	
#define CH452_DIG7      0x0f00		            //数码管位7显示


// Note: I2C Macros used in this example can be found in the 
// DSP280x_I2C_defines.h file

// Prototype statements for functions found within this file.
void   I2CA_Init(void);
Uint16 I2CA_WriteData(struct I2CMSG *msg);
Uint16 I2CA_ReadData(struct I2CMSG *msg);
interrupt void i2c_int1a_isr(void);
void pass(void);
void fail(void);

void CH452_Write(unsigned char);
unsigned char CH452_Read(void);
void CH452_I2c_Start();
void CH452_I2c_Stop();
void CH452_I2c_WrByte(unsigned char);
unsigned char  CH452_I2c_RdByte();

#define I2C_SLAVE_ADDR        0x50
#define I2C_NUMBYTES          4
#define I2C_EEPROM_HIGH_ADDR  0x00
#define I2C_EEPROM_LOW_ADDR   0x30

// Global variables
// Two bytes will be used for the outgoing address,
// thus only setup 14 bytes maximum
struct I2CMSG I2cMsgOut1={I2C_MSGSTAT_SEND_WITHSTOP, 
                          I2C_SLAVE_ADDR, 
                          I2C_NUMBYTES,
                          I2C_EEPROM_HIGH_ADDR,
                          I2C_EEPROM_LOW_ADDR,
                          0x12,                   // Msg Byte 1
                          0x34,                   // Msg Byte 2
                          0x56,                   // Msg Byte 3
                          0x78,                   // Msg Byte 4
                          0x9A,                   // Msg Byte 5      
                          0xBC,                   // Msg Byte 6
                          0xDE,                   // Msg Byte 7
                          0xF0,                   // Msg Byte 8
                          0x11,                   // Msg Byte 9
                          0x10,                   // Msg Byte 10
                          0x11,                   // Msg Byte 11 
                          0x12,                   // Msg Byte 12
                          0x13,                   // Msg Byte 13
                          0x12};                  // Msg Byte 14
                                            
                          
struct I2CMSG I2cMsgIn1={ I2C_MSGSTAT_SEND_NOSTOP, 
                          I2C_SLAVE_ADDR, 
                          I2C_NUMBYTES,
                          I2C_EEPROM_HIGH_ADDR,
                          I2C_EEPROM_LOW_ADDR};
                          
struct I2CMSG *CurrentMsgPtr;				// Used in interrupts
Uint16 PassCount;
Uint16 FailCount;

void DELAY_1US()
{Uint16 i;
for(i=0;i<1000;i++)
{
}
}

void main(void)
{
   Uint16 Error;
   Uint16 i;
   
   CurrentMsgPtr = &I2cMsgOut1;

// Step 1. Initialize System Control:
// PLL, WatchDog, enable Peripheral Clocks
// This example function is found in the DSP280x_SysCtrl.c file.
   InitSysCtrl();


// Step 2. Initalize GPIO: 
// This example function is found in the DSP280x_Gpio.c file and
// illustrates how to set the GPIO to it's default state.
// InitGpio();    
// Setup only the GP I/O only for I2C functionality
   InitI2CGpio();

// Step 3. Clear all interrupts and initialize PIE vector table:
// Disable CPU interrupts 
   DINT;   

// Initialize PIE control registers to their default state.
// The default state is all PIE interrupts disabled and flags
// are cleared.  
// This function is found in the DSP280x_PieCtrl.c file.
   InitPieCtrl();

// Disable CPU interrupts and clear all CPU interrupt flags:
   IER = 0x0000;
   IFR = 0x0000;

// Initialize the PIE vector table with pointers to the shell Interrupt 
// Service Routines (ISR).  
// This will populate the entire table, even if the interrupt
// is not used in this example.  This is useful for debug purposes.
// The shell ISR routines are found in DSP280x_DefaultIsr.c.
// This function is found in DSP280x_PieVect.c.
   InitPieVectTable();

// Interrupts that are used in this example are re-mapped to
// ISR functions found within this file.  
   EALLOW;	// This is needed to write to EALLOW protected registers
   PieVectTable.I2CINT1A = &i2c_int1a_isr;
   EDIS;   // This is needed to disable write to EALLOW protected registers 

// Step 4. Initialize all the Device Peripherals:
// This function is found in DSP280x_InitPeripherals.c
// InitPeripherals(); // Not required for this example
   I2CA_Init();

// Step 5. User specific code
   
   // Clear Counters
   PassCount = 0;
   FailCount = 0;
   
   // Clear incoming message buffer
   for (i = 0; i < I2C_MAX_BUFFER_SIZE; i++)
   {
       I2cMsgIn1.MsgBuffer[i] = 0x0000;
   }

// Enable interrupts required for this example

// Enable I2C interrupt 1 in the PIE: Group 8 interrupt 1
   PieCtrlRegs.PIEIER8.bit.INTx1 = 1;

// Enable CPU INT8 which is connected to PIE group 8
   IER |= M_INT8;
   EINT;

	CH452_Write(CH452_SYSON1);	//两线制方式，如果SDA用做按键中断输出，那么命令应该为(0x04,0x23)
	DELAY_1US();
	CH452_Write(CH452_BCD);   // BCD译码,8个数码管
	DELAY_1US();
	CH452_Write(CH452_DIG0 | 8);  // 显示字符8
	DELAY_1US();
	CH452_Write(CH452_DIG1 | 8);
	DELAY_1US();
	CH452_Write(CH452_DIG2 | 8);
	DELAY_1US();
	CH452_Write(CH452_DIG3 | 8);
	DELAY_1US();
	CH452_Write(CH452_DIG4 | 8);
	DELAY_1US();
	CH452_Write(CH452_DIG5 | 8);
	DELAY_1US();
	CH452_Write(CH452_DIG6 | 8);
	DELAY_1US();
	CH452_Write(CH452_DIG7 | 8);
	DELAY_1US();


//CH452_SDA_SET;
//CH452_SDA_CLR;

//CH452_SCL_SET;
//CH452_SCL_CLR;
   // Application loop
   for(;;)
   {
   CH452_Write(CH452_DIG0 | 8);
   DELAY_1US();
   DELAY_1US();
/*
      //////////////////////////////////
      // Write data to EEPROM section //
      //////////////////////////////////

      // Check the outgoing message to see if it should be sent.
      // In this example it is initialized to send with a stop bit.
      if(I2cMsgOut1.MsgStatus == I2C_MSGSTAT_SEND_WITHSTOP)
      {
         Error = I2CA_WriteData(&I2cMsgOut1);
         // If communication is correctly initiated, set msg status to busy
         // and update CurrentMsgPtr for the interrupt service routine.
         // Otherwise, do nothing and try again next loop. Once message is
         // initiated, the I2C interrupts will handle the rest. Search for
         // ICINTR1A_ISR in the i2c_eeprom_isr.c file.
         if (Error == I2C_SUCCESS)
         {
            CurrentMsgPtr = &I2cMsgOut1;
            I2cMsgOut1.MsgStatus = I2C_MSGSTAT_WRITE_BUSY;
         }
      }  // end of write section

      ///////////////////////////////////
      // Read data from EEPROM section //
      ///////////////////////////////////

      // Check outgoing message status. Bypass read section if status is
      // not inactive.
      if (I2cMsgOut1.MsgStatus == I2C_MSGSTAT_INACTIVE)
      {
         // Check incoming message status.
         if(I2cMsgIn1.MsgStatus == I2C_MSGSTAT_SEND_NOSTOP)
         {
            // EEPROM address setup portion
            while(I2CA_ReadData(&I2cMsgIn1) != I2C_SUCCESS)
            {
               // Maybe setup an attempt counter to break an infinite while
               // loop. The EEPROM will send back a NACK while it is performing
               // a write operation. Even though the write communique is
               // complete at this point, the EEPROM could still be busy
               // programming the data. Therefore, multiple attempts are
               // necessary.
            }
            // Update current message pointer and message status
            CurrentMsgPtr = &I2cMsgIn1;
            I2cMsgIn1.MsgStatus = I2C_MSGSTAT_SEND_NOSTOP_BUSY;
         }
            
         // Once message has progressed past setting up the internal address
         // of the EEPROM, send a restart to read the data bytes from the
         // EEPROM. Complete the communique with a stop bit. MsgStatus is
         // updated in the interrupt service routine.
         else if(I2cMsgIn1.MsgStatus == I2C_MSGSTAT_RESTART)
         {
            // Read data portion
            while(I2CA_ReadData(&I2cMsgIn1) != I2C_SUCCESS)
            {
               // Maybe setup an attempt counter to break an infinite while
               // loop.
            }
            // Update current message pointer and message status
            CurrentMsgPtr = &I2cMsgIn1;
            I2cMsgIn1.MsgStatus = I2C_MSGSTAT_READ_BUSY;
         }
      }  // end of read section
*/      
   }   // end of for(;;)
}   // end of main


void I2CA_Init(void)
{
   // Initialize I2C
   I2caRegs.I2CSAR = 0x0050;		// Slave address - EEPROM control code
   I2caRegs.I2CPSC.all = 9;			// Prescaler - need 7-12 Mhz on module clk
   I2caRegs.I2CCLKL = 10;			// NOTE: must be non zero
   I2caRegs.I2CCLKH = 5;			// NOTE: must be non zero
   I2caRegs.I2CIER.all = 0x24;		// Enable SCD & ARDY interrupts

   I2caRegs.I2CMDR.all = 0x0020;	// Take I2C out of reset