readme2.txt

FOCAS2的HSSB开发包.做FANUC数控采集的必备.

      The HSSB Driver has been updated correctly.
      You will need to exit and restart Windows so that the new setting
      can take effect.
      Do you want to restart your computer now?

 Please update the HSSB driver according to the procedure of [9],[10],[11],[12]
 and [13] when failing in the update of the HSSB driver.


==========================================================================
[9] Update method (Windows 95/98)
==========================================================================

    To update the driver from 16 bit version, install this driver according
    to the section [2] of this document.

    To update the driver from previous 32 bit version, follow these steps.

 1. Terminate Ncboot32.exe.
    Right-click the icon on the system tray and click "End" on the pop up
    menu.

 2. Click [Start] button.
        [Start] menu is displayed.

 3. Point [Setting], then click [Control Panel].
        [Control Panel] window is displayed.

 4. Double-click [System] of [Control Panel].
        [System Properties] window is displayed.

 5. Click [Device Manager] tab.

 6. Click [HSSB Type 2] of [FANUC Open CNC].

 7. Click [Remove] button of [System Properties] window.
        [Confirm Device Removal] window is displayed.

 8. Click [OK] button.
        HSSB Type2 is deleted.

 9. If there are two or more HSSB Type2 devices, repeats from step 6.

10. If you add the PCI HSSB interface board, shut down the Windows and
    turn off the computer.
    Then insert the PCI HSSB interface board into the PCI slot.

11. Restart Windows and install this driver according to the section [2].


 (Note) The FS300i/310i/320i is not supported by the HSSB driver for
        Windows 95/98.


==========================================================================
[10] Update method (Windows NT)
==========================================================================

 1. Terminate Ncboot32.exe.
    Right-click the icon on the system tray and click "End" on the pop up
    menu.

 2. Copy files.
    Copy \HSSB\COMMON\NCBOOT32.EXE and \HSSB\NT40\HSSB2.CPL to the Windows
    NT's system32 folder.
    Copy \HSSB\NT40\MMCNCD.SYS to the system32\drivers folder.

 3. Restart Windows NT.


 (Note) The FS300i/310i/320i is not supported by the HSSB driver for
        Windows NT.


==========================================================================
[11] Update method (Windows 2000)
==========================================================================

 1. Terminate Ncboot32.exe.
    Right-click the icon on the system tray and click "End" on the pop up
    menu.

 2. Copy files.
    Copy \HSSB\COMMON\NCBOOT32.EXE and \HSSB\WIN2K\HSSB2.CPL to the Windows
    2000's system32 folder.
    Copy \HSSB\WIN2K\MMCNCD.SYS to the system32\drivers folder.

 3. Restart Windows 2000.


==========================================================================
[12] Update method (Windows XP)
==========================================================================

 1. Terminate Ncboot32.exe.
    Right-click the icon on the system tray and click "End" on the pop up
    menu.

 2. Copy files.
    Copy \HSSB\COMMON\NCBOOT32.EXE, \HSSB\WIN2K\HSSB2.CPL and 
    \HSSB|WINXP\HSSB2.CPL.MANIFEST to the Windows XP's system32 folder.
    Copy \HSSB\WIN2K\MMCNCD.SYS to the system32\drivers folder.

 3. Restart Windows XP.


==========================================================================
[13] Update method (Windows Vista)
==========================================================================

 1. Terminate Ncboot32.exe.
    Right-click the icon on the system tray and click "End" on the pop up
    menu.

 2. Copy files.
    Copy \HSSB\VISTA\NCBOOT32.EXE and \HSSB\VISTA\HSSBSET.EXE to the Windows
    Vista's system32 folder.
    Copy \HSSB\WIN2K\MMCNCD.SYS to the system32\drivers folder.

 3. Restart Windows Vista.


==========================================================================
[14] Delete HSSB Driver (Windows 95/98)
==========================================================================

 1. Open [System] -> [Device Manager] in the Control Panel.

 2. Delete all driver in [FANUC Open CNC] section.

 3. Execute REGEDIT.EXE.

 4. Remove "ncboot32.exe" in "HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\
    CurrentVersion\Run" key by using REGEDIT.EXE.

 5. Restart PC.

 6. Delete mmcncd.vxd, hssbui.dll ncboot32.exe in Windows System folder.

==========================================================================
[15] Delete HSSB Driver (Windows NT)
==========================================================================

 1. Open [Device] in the Control Panel.

 2. Select "mmcncd" and click [Stop] button.

 3. Click [Startup] button and select [Disabled] in [Startup Type] group.

 4. Close the Control Panel.

 5. Terminate Ncboot32.exe.
    Right-click the icon[FANUC Open CNC] on the system tray and click "End" on
    the pop up menu.

 6. Set this CD onto the CD-ROM drive, then open the folder "d:\hssb\nt40"
    by explorer.
    ("d:" is the drive letter for the CD-ROM.  If other drive letter is
     assigned to your drive, change it properly.)

 7. Right-click the UNHSSB.INF file and click [install] on the pop up menu.
        The driver and the registry will be removed.

 8. Turn off PC, then remove the HSSB interface boards.


==========================================================================
[16] Delete HSSB Driver (Windows 2000)
==========================================================================

 1. Start Windows 2000. Never open Control Panel.

 2. Terminate Ncboot32.exe.
    Right-click the icon[FANUC Open CNC] on the system tray and click "End" on
    the pop up menu.

 3. Set this CD onto the CD-ROM drive, then open the folder "d:\hssb\win2k"
     by explorer.
    ("d:" is the drive letter for the CD-ROM.  If other drive letter is
     assigned to your drive, change it properly.)

 4. Right-click the UNHSSB.INF file and click [install] on the pop up menu.
        The driver and the registry will be removed.

 5. Open [System] in the Control Panel.

 6. Right-click [Hardware] tab, and continuously right-click
    [Device Manager...] button.

 7. Open the properties of all driver in [FANUC Open CNC] of device list. 
    And click [General] tab, then set "Do not use this device(disable)" in 
    [Device usage:].  Moreover, delete all these drivers.

 8. Turn off PC, then remove the HSSB interface boards.


 (Note) If the control panel was opened even once, the HSSB icon is not deleted. 


==========================================================================
[17] Delete HSSB Driver (Windows XP)
==========================================================================

 1. Start Windows XP. Never open Control Panel.
 
 2. Terminate Ncboot32.exe.
    Right-click the icon[FANUC Open CNC] on the system tray and click "End" on
    the pop up menu.

 3. Set this CD onto the CD-ROM drive, then open the folder "d:\hssb\winxp"
    by explorer.
    ("d:" is the drive letter for the CD-ROM.  If other drive letter is
     assigned to your drive, change it properly.)

 4. Right-click the UNHSSB.INF file and click [install] on the pop up menu.
        The driver and the registry will be removed.

 5. Click [Start] button.
        [Start] menu is displayed.

 6. Point [My Computer], then right-click. And click [Properties] from pulldown
    menu.
        [System Properties] screen is displayed.

 5. Open [System] in the Control Panel.

 7. Right-click [Hardware] tab, and continuously right-click
    [Device Manager...] button.

 8. Open the properties of all driver in [FANUC Open CNC] of device list. 
    And click [General] tab, then set "Do not use this device(disable)" in 
    [Device usage:].  Moreover, delete all these drivers.

 9. Turn off PC, then remove the HSSB interface boards.


 (Note) If the control panel was opened even once, the HSSB icon is not deleted. 


==========================================================================
[18] Delete HSSB Driver (Windows Vista)
==========================================================================

 1. Start Windows Vista. 

 2. Set this CD onto the CD-ROM drive, then open the folder "d:\hssb\vista"
    by explorer.
    ("d:" is the drive letter for the CD-ROM.  If other drive letter is
     assigned to your drive, change it properly.)

 3. Execute DelDrv.exe

 4. Because the [User Account Control] window is displayed, click [Allow].

 5. Select [HSSB Driver] from [Select the kind of driver.], then click [Delete]
    button.

 6. Because there is a question of [HSSB Driver is deleted. Are you sure?],
    click [Yes] button.
        The driver and the registry will be removed.

 7. Click [Start] button.
        [Start] menu is displayed.

 8. Point [Computer], then right-click. And click [Properties] from pulldown
    menu.
        [System] screen is displayed.

 9. Click [Device Manager] on [Tasks] list.

10. Because the [User Account Control] window is displayed, click [Continue]
    button.
        [Device Manager] window is diaplayed.

11. Open the properties of all driver in [FANUC Open CNC] of device list. 
    And click [driver] tab, then click [Disable] button. Moreover, uninstall
    all these drivers.

12. Turn off PC, then remove the HSSB interface boards.


==========================================================================
[19] Change in the registry information (Windows 95/98)
==========================================================================

 The information of the node name for Windows95/98 registry has been
 changed as follows.

  - since Edition 1.6 or later

   HKEY_LOCAL_MACHINE
    |
     System
     |
      CurrentControlSet
      |
       Services
       |
        Class
        |
         CNC
         |
          0000                     <- The software key for the first HSSB
         |                            interface board.
         |   NodeName0 "FS160-1"   <- The node name for channel 1.
         |   NodeName1 "FS160-2"   <- The node name for channel 2.
         |   *********
          0001                     <- The software key for the second HSSB
         |                            interface board.
         |   NodeName0 "FS150-1"   <- The node name for channel 1.
         |   NodeName1 "FS150-2"   <- The node name for channel 2.
         |   *********


 - until Edition 1.5 or former

   HKEY_LOCAL_MACHINE
    |
     Enum
     |
      Root
      |
       CNC
       |
        0000                     <- The hardware key for node 0.
       |   DeviceDesc "FS160-1"  <- The node name for node 0.
       |   *********
        0001                     <- The hardware key for node 1.
       |   DeviceDesc "FS160-2"  <- The node name for node 1.
       |   *********