readme2.txt

FOCAS2的HSSB开发包.做FANUC数控采集的必备.

                             README2.TXT  File
                README file for FANUC Open CNC  HSSB driver

            (C) Copyright FANUC LTD, 1996-2007, All Rights Reserved.


This document provides the information about the HSSB driver.
Please read this document before using the software in this disk.

--------------------------------------------------------------------------
[1] File summary
[2] Installation (Windows 95/98)
[3] Installation (Windows NT)
[4] Installation (Windows 2000)
[5] Installation (Windows XP)
[6] Installation (Windows Vista)
[7] Installation (Upgrade to Windows 2000 from Windows 95/98/NT)
[8] Update method (Common)
[9] Update method (Windows 95/98)
[10] Update method (Windows NT)
[11] Update method (Windows 2000)
[12] Update method (Windows XP)
[13] Update method (Windows Vista)
[14] Delete HSSB Driver (Windows 95/98)
[15] Delete HSSB Driver (Windows NT)
[16] Delete HSSB Driver (Windows 2000)
[17] Delete HSSB Driver (Windows XP)
[18] Delete HSSB Driver (Windows Vista)
[19] Change in the registry information (Windows 95/98)
--------------------------------------------------------------------------


==========================================================================
[1] File summary
==========================================================================

    <HSSB> folder contains the HSSB driver.

<HSSB>\NCBOOT32.DOC  :  English document.
<HSSB>\NCBOOT32J.DOC :  Japanese document.
    Operation manual for NCBOOT32.EXE.
    Open these documents by Microsoft Word 97 or later.
    When you used the Wordpad, the document files might be not open.


<HSSB>\UPDATE.EXE : Utility program to update the HSSB driver.


<HSSB\WIN95> : Windows 95/98 driver.

<HSSB\WIN95>\HSSB.INF :
    Device information file for HSSB driver.  This is used by "Add New
    Hardware Wizard".

<HSSB\WIN95>\MMCNCD.VXD :
    Virtual device driver to run libraries provided by FANUC on Windows.

<HSSB\WIN95>\HSSBUI.DLL :
    Setting program for HSSB driver.


<HSSB\NT40> : Windows NT 4.0 driver.

<HSSB\NT40>\HSSB.INF :
    Device information file for HSSB driver.  This is used at the installation.

<HSSB\NT40>\MMCNCD.SYS :
    Device driver to run libraries provided by FANUC on Windows NT.

<HSSB\NT40>\HSSB2.CPL :
    The Control Panel applet to set the HSSB driver configuration.

<HSSB\NT40>\UNHSSB.INF :
    Device information file for HSSB driver.  This is used at the 
    uninstallation.


<HSSB\WIN2K> : Windows 2000 driver.

<HSSB\WIN2K>\HSSB.INF :
    Device information file for HSSB driver.  This is used at the installation.

<HSSB\WIN2K>\MMCNCD.SYS :
    Device driver to run libraries provided by FANUC on Windows 2000.

<HSSB\WIN2K>\HSSB2.CPL :
    The Control Panel applet to set the HSSB driver configuration.


<HSSB\WINXP> : Windows XP driver.

<HSSB\WINXP>\HSSB.INF :
    Device information file for HSSB driver.  This is used at the installation.

<HSSB\WINXP>\HSSB2.CPL.MANIFEST :
    This file is used to construct Visual Style of Windows XP onto the Control
    Panel Applet for HSSB driver.


<HSSB\COMMON> : Common files for Windows 95/98/NT/2000 and XP.

<HSSB\COMMON>\NCBOOT32.EXE :
    HSSB driver support utility, which is resident on System tray and provides
    the following functions.
        - BOOT function (Maintain the CNC system file, Backup the SRAM, etc.)
        - IPL menu of CNC
        - Display of CNC power-on screen
        - Display of CNC alarm screen
        - Reconnection on the communication failure
        - Start up the registered application program using data window library


<HSSB\VISTA> : Windows Vista driver.

<HSSB\VISTA>\HSSB.INF :
    Device information file for HSSB driver.  This is used at the installation.

<HSSB\VISTA>\MMCNCD.SYS :
    Device driver to run libraries provided by FANUC on Windows Vista.
<HSSB\VISTA>\HSSBSET.EXE :
    The Control Panel applet to set the HSSB driver configuration.

<HSSB\VISTA>\NCBOOT32.EXE
    It is the same file as <HSSB\COMMON>\NCBOOT32.EXE.

<HSSB\VISTA>\DelDrv.EXE
    This is used at the uninstallation.


==========================================================================
[2] Installation (Windows 95/98)
==========================================================================

    In case of HSSB multi-connection, determine correspondence between nodes
    and connected CNCs.
    When two or more HSSB interface boards are used, each node is sequentially
    allotted from 0 to each board as follows.

     - When the ISA HSSB interface board and the PCI HSSB board are also
       installed, first, the nodes are allotted to the ISA HSSB interface
       board, then, the nodes are allotted to the PCI HSSB interface board.

     - When two or more PCI HSSB interface boards are installed, the nodes are
       allotted first from the PCI HSSB interface board inserted in lower PCI
       slot number.

    Next, do the following according to the kind of the HSSB interface board.
     - For the ISA HSSB interface board
       Decide the I/O port address to be allocated on the HSSB board and
       set the rotary switch on the HSSB board. (In case of PC integrated type
       i-series, Intelligent Terminal type 2 which do not have the ISA
       extension unit, I/O port address is fixed at 280H-28BH.)

     - For the PCI HSSB interface board
       Nothing need to be done. (The I/O port address is automatically set
       by the HSSB driver. FANUC PANEL i and CNC Display Unit with Personal
       Computer Function are also included in this case.)


    To install the HSSB driver to your system, use "Update Device Driver
    Wizard" or "Add New Hardware Wizard".

    There are following two methods of installation procedures for the driver.

        A.  Method by the automatic detection by Windows
        B.  Method by the manual operation


-------------------------------------------------------------------------------
 A. Method by the automatic detection by Windows

 1. When Windows is started, the PCI HSSB interface board is detected as
    "PCI Communication Device".
        [Update Device Driver Wizard] window is displayed.

     (When the PCI HSSB interface board is not detected automatically by
      Windows, install the driver according to following procedure,
     "B. Method by the manual operation".)

 2. Click [Next] button.
        "Windows was unable to locate a driver for this device" message is
        displayed.

 3. Click [Other Locations...] button. Set this CD onto the CD-ROM drive.

 4. Enter "d:\hssb\win95" on [Location] box, then click [OK] button.
    ("d:" is the drive letter for the CD-ROM.  If other drive letter is
    assigned to your drive, change it properly.)
        "Windows found the following updated driver for this device"
        message is displayed.

 5. Click [Finish] button.
        "Please insert the disk labeled "FANUC Open CNC Drivers and
        Libraries Disk #1" and the click [OK]." message is displayed.

 6. Click [OK] button.
        [Copying Files...] window is displayed.

 7. Enter "d:\hssb\win95" on [Copy files from] box, then click [OK] button.
        Files are copied.

        The installation is automatically done if there are two or more PCI
        HSSB interface boards.

        Afterwards, Windows is restarted.

 8. Click [Start] button.
        [Start] menu is displayed.

 9. Point [Setting], then click [Control Panel].
        [Control Panel] window is displayed.

10. Double-click [System] of [Control Panel].
        [System Properties] window is displayed.

11. Click [Device Manager] tab.

12. Double-click [FANUC HSSB Type 2 (PCI ? Channel)] (? is 1 or 2) of
    [FANUC Open CNC].
        [FANUC HSSB Type 2 (PCI ? Channel)] window is displayed.

13. Click [Settings] tab.

14. Enter proper name which indicates the machine connected to the HSSB board
   (for example, "FS160 - No.1", "Milling Machine") to [Node name] within 19
   characters.

15. Select connecting CNC type from [CNC type] and click it.

16. Click [OK] button.
        [System Setting Change] window is displayed, and "Do you want to
        shut down your computer now?" message is displayed.

17. When setting to the PCI HSSB interface board is required, click [No] and
    go back to step 12.
    Sets the all PCI HSSB interface boards.

    When you install the driver for the ISA HSSB interface board succeedingly,
    click [No] button in [System Setting Change] window.
    Install the driver for the ISA HSSB interface board according to
    "B. Method by the manual operation".

    When the installation on all the HSSB interface boards finishes, click
    [Yes] button in [System Setting Change] window.


-------------------------------------------------------------------------------
 B. Method by the manual operation

 1. Click [Start] button.
        [Start] menu is displayed.

 2. Point [Setting], then click [Control Panel].
        [Control Panel] window is displayed.

 3. Double-click [Add New Hardware].
        [Add New Hardware Wizard] window is displayed.

 4. Click [Next] button.
        "Do you want Windows to search for your new hardware?" message is
        displayed.

 5. Click [No], then click [Next] button.

 6. When the item of [FANUC Open CNC] is not displayed on [Hardware types]
    list box, click [Other devices], then click [Next] button.

    When the item of [FANUC Open CNC] is displayed on [Hardware types] list
    box, click [FANUC Open CNC], then click [Next] button.
        [Models] list box is displayed.

        When the following [Models] lists are displayed, go step 9.
          FANUC HSSB Type 2 (ISA 1 Channel)
          FANUC HSSB Type 2 (ISA 2 Channel)
          FANUC HSSB Type 2 (PCI 1 Channel)
          FANUC HSSB Type 2 (PCI 2 Channel)

        When the following [Models] list is displayed, go step 7.
          HSSB Type 2

 7. Click [Have Disk] button. Set this CD onto the CD-ROM drive.

 8. Enter "d:\hssb\win95" on [Copy manufacturer's files from] box, then
    click [OK] button. ("d:" is the drive letter for the CD-ROM.  If other
    drive letter is assigned to your drive, change it properly.)
        The following [Models] list box is displayed.
          FANUC HSSB Type 2 (ISA 1 Channel)
          FANUC HSSB Type 2 (ISA 2 Channel)
          FANUC HSSB Type 2 (PCI 1 Channel)
          FANUC HSSB Type 2 (PCI 2 Channel)

 9. Click the item corresponding to the HSSB interface board which should be
    used.
    In case of PC integrated type i-series, Intelligent Terminal type 2, select
    "FANUC HSSB Type 2 (ISA 1 Channel)".
    In case of FANUC PANEL i and CNC Display Unit with Personal Computer
    Function, select "FANUC HSSB Type 2 (PCI 1 Channel)".

10. Click [Next] button.
        "Windows can install your hardware, using the following settings"
        message is displayed.

11. Click [Next] button
        After copying files from the floppy disk, "Windows has finished
        installing the software necessary to support your new hardware."
        message is displayed.

12. Click [Finish] button.
        [System Setting Change] window is displayed, and "Do you want to
        shut down your computer now?" message is displayed.

13. Click [No] button. Remove this CD from the CD-ROM drive.

14. Double-click [System] of [Control Panel].
        [System Properties] window is displayed.

15. Click [Device Manager] tab.

16. Double-click [FANUC HSSB Type 2 (??? ? Channel)] ('??? ?' is 'ISA 1',
    'ISA 2', 'PCI 1' or 'PCI 2') of [FANUC Open CNC].
        [FANUC HSSB Type 2 (??? ? Channel) Properties] window is displayed.

17. Click [Settings] tab.

18. Enter proper name which indicates the machine connected to the HSSB board
   (for example, "FS160 - No.1", "Milling Machine") to [Node name] within 19
   characters.

19. Select connecting CNC type from [CNC type] and click it.

20. In case of the setting to the PCI HSSB interface board, go step 25.

21. Click [Resources] tab.
        [Resources] list is displayed.