cim_numericsensor.mof

Pegasus is an open-source implementationof the DMTF CIM and WBEM standards. It is designed to be por

          "property. Its value is recorded as plus/minus hundredths of "
          "a percent. Accuracy, along with Resolution, is used to "
          "calculate the actual value of the measured physical "
          "property. Accuracy may vary depending on whether the Device "
          "is linear over its dynamic range."), 
       Units ( "Hundredths of Percent" ), 
       MappingStrings { "MIF.DMTF|Temperature Probe|002.19",
          "MIF.DMTF|Electrical Current Probe|001.19",
          "MIF.DMTF|Voltage Probe|001.19" }]
   sint32 Accuracy;

      [Description (
          "Indicates that the Sensor is linear over its dynamic range.")]
   boolean IsLinear;

      [Description (
          "Indicates the margin built around the thresholds. This "
          "margin prevents unnecessary state changes when the Sensor "
          "reading may fluctuate very close to its thresholds. This "
          "could be due to the Sensor's tolerance/accuracy/resolution "
          "or due to environmental factors. Once a threshold is "
          "crossed, the state of the Sensor should change. However, "
          "the state should not fluctuate between the old and new "
          "states unless the Sensor's change in the reading exceeds "
          "the hysteresis value. The units for this measurement are "
          "determined by BaseUnit*UnitModifier/RateUnit.")]
   uint32 Hysteresis;

      [Description (
          "The Sensor's threshold values specify the ranges (min and "
          "max values) for determining whether the Sensor is operating "
          "under Normal, NonCritical, Critical or Fatal conditions. If "
          "Current Reading is between LowerThresholdNonCritical and "
          "Upper ThresholdNonCritical, then the Sensor is reporting a "
          "normal value. If CurrentReading is between "
          "LowerThresholdNonCritical and LowerThresholdCritical, then "
          "the CurrentState is NonCritical."), 
       MappingStrings { "MIF.DMTF|Temperature Probe|002.11",
          "MIF.DMTF|Electrical Current Probe|001.11",
          "MIF.DMTF|Voltage Probe|001.11" }]
   sint32 LowerThresholdNonCritical;

      [Description (
          "The Sensor's threshold values specify the ranges (min and "
          "max values) for determining whether the Sensor is operating "
          "under Normal, NonCritical, Critical or Fatal conditions. If "
          "the CurrentReading is between LowerThresholdNonCritical and "
          "UpperThresholdNonCritical, then the Sensor is reporting a "
          "normal value. If the CurrentReading is between "
          "UpperThreshold NonCritical and UpperThresholdCritical, then "
          "the CurrentState is NonCritical."), 
       MappingStrings { "MIF.DMTF|Temperature Probe|002.12",
          "MIF.DMTF|Electrical Current Probe|001.12",
          "MIF.DMTF|Voltage Probe|001.12" }]
   sint32 UpperThresholdNonCritical;

      [Description (
          "The Sensor's threshold values specify the ranges (min and "
          "max values) for determining whether the Sensor is operating "
          "under Normal, NonCritical, Critical or Fatal conditions. If "
          "the CurrentReading is between LowerThresholdCritical and "
          "Lower ThresholdFatal, then the CurrentState is Critical."), 
       MappingStrings { "MIF.DMTF|Temperature Probe|002.13",
          "MIF.DMTF|Electrical Current Probe|001.13",
          "MIF.DMTF|Voltage Probe|001.13" }]
   sint32 LowerThresholdCritical;

      [Description (
          "The Sensor's threshold values specify the ranges (min and "
          "max values) for determining whether the Sensor is operating "
          "under Normal, NonCritical, Critical or Fatal conditions. If "
          "the CurrentReading is between UpperThresholdCritical and "
          "Upper ThresholdFatal, then the CurrentState is Critical."), 
       MappingStrings { "MIF.DMTF|Temperature Probe|002.14",
          "MIF.DMTF|Electrical Current Probe|001.14",
          "MIF.DMTF|Voltage Probe|001.14" }]
   sint32 UpperThresholdCritical;

      [Description (
          "The Sensor's threshold values specify the ranges (min and "
          "max values) for determining whether the Sensor is operating "
          "under Normal, NonCritical, Critical or Fatal conditions. If "
          "the CurrentReading is below LowerThresholdFatal, then the "
          "Current State is Fatal."), 
       MappingStrings { "MIF.DMTF|Temperature Probe|002.15",
          "MIF.DMTF|Electrical Current Probe|001.15",
          "MIF.DMTF|Voltage Probe|001.15" }]
   sint32 LowerThresholdFatal;

      [Description (
          "The Sensor's threshold values specify the ranges (min and "
          "max values) for determining whether the Sensor is operating "
          "under Normal, NonCritical, Critical or Fatal conditions. If "
          "the CurrentReading is above UpperThresholdFatal, then the "
          "Current State is Fatal."), 
       MappingStrings { "MIF.DMTF|Temperature Probe|002.16",
          "MIF.DMTF|Electrical Current Probe|001.16",
          "MIF.DMTF|Voltage Probe|001.16" }]
   sint32 UpperThresholdFatal;

      [Description (
          "An array representing the thresholds supported by this "
          "Sensor."), 
       ValueMap { "0", "1", "2", "3", "4", "5" }, 
       Values { "LowerThresholdNonCritical",
          "UpperThresholdNonCritical", "LowerThresholdCritical",
          "UpperThresholdCritical", "LowerThresholdFatal",
          "UpperThresholdFatal" }]
   uint16 SupportedThresholds[];

      [Description (
          "An array representing the thresholds that are currently "
          "enabled for this Sensor."), 
       ValueMap { "0", "1", "2", "3", "4", "5" }, 
       Values { "LowerThresholdNonCritical",
          "UpperThresholdNonCritical", "LowerThresholdCritical",
          "UpperThresholdCritical", "LowerThresholdFatal",
          "UpperThresholdFatal" }]
   uint16 EnabledThresholds[];

      [Description (
          "An array representing the writable thresholds supported by "
          "Sensor."), 
       ValueMap { "0", "1", "2", "3", "4", "5" }, 
       Values { "LowerThresholdNonCritical",
          "UpperThresholdNonCritical", "LowerThresholdCritical",
          "UpperThresholdCritical", "LowerThresholdFatal",
          "UpperThresholdFatal" }]
   uint16 SettableThresholds[];

      [Description (
          "This method resets the values of the thresholds to hardware "
          "defaults. This method returns 0 if successful, 1 if "
          "unsupported and any other value if an error occurred. In a "
          "subclass, the set of possible return codes could be "
          "specified, using a ValueMap qualifier on the method. The "
          "strings to which the ValueMap contents are 'translated' may "
          "also be specified in the subclass as a Values array "
          "qualifier.")]
   uint32 RestoreDefaultThresholds(); 

      [Deprecated { "No Value" }, Description (
          "The use of this method is being deprecated, since Current "
          "senor reading can be retrieved through the GetInstance "
          "operation. \n"
          "For a non-linear Sensor, the resolution, accuracy, "
          "tolerance and hysteresis vary as the current reading moves. "
          "This method can be used to get these factors for a given "
          "reading. It returns 0 if successful, 1 if unsupported, and "
          "any other value if an error occurred. In a subclass, the "
          "set of possible return codes could be specified, using a "
          "ValueMap qualifier on the method. The strings to which the "
          "ValueMap contents are 'translated' may also be specified in "
          "the subclass as a Values array qualifier.")]
   uint32 GetNonLinearFactors( 
         [IN, Description (
             "The sensor reading to get information for.")]
      sint32 SensorReading, 
         [IN ( false ), OUT, Description (
             "The accuracy of the reading.")]
      sint32 Accuracy, 
         [IN ( false ), OUT, Description (
             "The resolution of the reading.")]
      uint32 Resolution, 
         [IN ( false ), OUT, Description (
             "The tolerance of the reading.")]
      sint32 Tolerance, 
         [IN ( false ), OUT, Description (
             "The Hysteresis of the reading.")]
      uint32 Hysteresis); 
};