cim_uninterruptiblepowersupply.mof

Pegasus is an open-source implementationof the DMTF CIM and WBEM standards. It is designed to be por

// Copyright (c) 2005 DMTF.  All rights reserved.
// <change cr="CIMCoreCR00735.001" type ="change">Update of
// descriptions based on Tech Edit review.</
// <change cr="ArchCR00066.004" type="add">Add UmlPackagePath
// qualifier values to CIM Schema.</change>
// ==================================================================
//  CIM_UninterruptiblePowerSupply
// ==================================================================
   [UMLPackagePath ( "CIM::Device::CoolingAndPower" ),
       Version ( "2.10.0" ), Description (
       "Capabilities and management of an UninterruptiblePowerSupply. "
       "The properties of the UPS Device indicate when incoming power "
       "is trimmed or boosted, and the aggregated information of the "
       "batteries, generators, and so on that comprise the Device. "
       "These individual components (for example, multiple batteries) "
       "can also be independently modeled and associated with the UPS.")]
class CIM_UninterruptiblePowerSupply : CIM_PowerSupply {

      [Override ( "Range1InputVoltageLow" ), Description (
          "If the voltage (in millivolts) drops below the value "
          "specified by Range1InputVoltageLow, the UPS will compensate "
          "by boosting the voltage using its power sources. A value of "
          "0 indicates that the voltage at which boosting occurs is "
          "'unknown'."), 
       Units ( "MilliVolts" )]
   uint32 Range1InputVoltageLow;

      [Override ( "Range1InputVoltageHigh" ), Description (
          "If the voltage (in millivolts) rises above the value "
          "specified by Range1InputVoltageHigh, the UPS will "
          "compensate by trimming the voltage. A value of 0 indicates "
          "that the voltage at which trimming occurs is 'unknown'."), 
       Units ( "MilliVolts" )]
   uint32 Range1InputVoltageHigh;

      [Override ( "Range2InputVoltageLow" ), Description (
          "If the voltage (in millivolts) drops below the value "
          "specified by Range2InputVoltageLow, the UPS will compensate "
          "by boosting the voltage using its power sources. A value of "
          "0 indicates that the voltage at which boosting occurs is "
          "'unknown'."), 
       Units ( "MilliVolts" )]
   uint32 Range2InputVoltageLow;

      [Override ( "Range2InputVoltageHigh" ), Description (
          "If the voltage (in millivolts) rises above the value "
          "specified by Range2InputVoltageHigh, the UPS will "
          "compensate by trimming the voltage. A value of 0 indicates "
          "that the voltage at which trimming occurs is 'unknown'."), 
       Units ( "MilliVolts" )]
   uint32 Range2InputVoltageHigh;

      [Description (
          "The indication of the capacity that remains in the UPS "
          "batteries, generator, and so on. A value of \"Normal\" (2) "
          "indicates that the remaining estimated minutes of run-time "
          "are greater than the 'low power' state defined for the UPS "
          "(typically two minutes). A value of \"Low\" (3) indicates "
          "that the remaining estimated minutes of run-time are less "
          "than or equal to the defined 'low power' state of the "
          "device. A value of \"Depleted\" (4) indicates that the UPS "
          "will be unable to sustain the present load when and if the "
          "utility power is lost (including the possibility that the "
          "utility power is currently absent)."), 
       ValueMap { "1", "2", "3", "4" }, 
       Values { "Unknown", "Normal", "Low", "Depleted" }, 
       MappingStrings { "MIF.DMTF|UPS Battery|001.1" }]
   uint16 RemainingCapacityStatus;

      [Description (
          "TimeOnBackup indicates the elapsed time in seconds since "
          "the UPS last switched to battery power, generator, or so on "
          "or the time since the UPS was last restarted, whichever is "
          "less. 0 is returned if the UPS is 'on line'."), 
       Units ( "Seconds" ), 
       MappingStrings { "MIF.DMTF|UPS Battery|001.2" }]
   uint32 TimeOnBackup;

      [Description (
          "EstimatedRunTime is an estimate in minutes of the time that "
          "depletion of the battery, generator, or other device, will "
          "occur under the present load conditions if the utility "
          "power is off or is lost and remains off."), 
       Units ( "Minutes" ), 
       MappingStrings { "MIF.DMTF|UPS Battery|001.3" }]
   uint32 EstimatedRunTime;

      [Description (
          "An estimate of the percentage of full charge remaining for "
          "a UPS (that uses battery technology)."), 
       Units ( "Percent" ), Gauge, 
       MappingStrings { "MIF.DMTF|UPS Battery|001.4" }]
   uint16 EstimatedChargeRemaining;
};