qla_init.c

来自「linux2.6.16版本」· C语言 代码 · 共 2,472 行 · 第 1/5 页

		} else if (IS_QLA2322(ha) || IS_QLA6322(ha))
			ha->fw_options[11] |= BIT_5 |
			    ((rx_sens & (BIT_1 | BIT_0)) << 2) |
			    (tx_sens & (BIT_1 | BIT_0));
	}

	/* FCP2 options. */
	/*  Return command IOCBs without waiting for an ABTS to complete. */
	ha->fw_options[3] |= BIT_13;

	/* LED scheme. */
	if (ha->flags.enable_led_scheme)
		ha->fw_options[2] |= BIT_12;

	/* Update firmware options. */
	qla2x00_set_fw_options(ha, ha->fw_options);
}

void
qla24xx_update_fw_options(scsi_qla_host_t *ha)
{
	int rval;

	/* Update Serial Link options. */
	if ((le16_to_cpu(ha->fw_seriallink_options24[0]) & BIT_0) == 0)
		return;

	rval = qla2x00_set_serdes_params(ha,
	    le16_to_cpu(ha->fw_seriallink_options24[1]),
	    le16_to_cpu(ha->fw_seriallink_options24[2]),
	    le16_to_cpu(ha->fw_seriallink_options24[3]));
	if (rval != QLA_SUCCESS) {
		qla_printk(KERN_WARNING, ha,
		    "Unable to update Serial Link options (%x).\n", rval);
	}
}

void
qla2x00_config_rings(struct scsi_qla_host *ha)
{
	struct device_reg_2xxx __iomem *reg = &ha->iobase->isp;

	/* Setup ring parameters in initialization control block. */
	ha->init_cb->request_q_outpointer = __constant_cpu_to_le16(0);
	ha->init_cb->response_q_inpointer = __constant_cpu_to_le16(0);
	ha->init_cb->request_q_length = cpu_to_le16(ha->request_q_length);
	ha->init_cb->response_q_length = cpu_to_le16(ha->response_q_length);
	ha->init_cb->request_q_address[0] = cpu_to_le32(LSD(ha->request_dma));
	ha->init_cb->request_q_address[1] = cpu_to_le32(MSD(ha->request_dma));
	ha->init_cb->response_q_address[0] = cpu_to_le32(LSD(ha->response_dma));
	ha->init_cb->response_q_address[1] = cpu_to_le32(MSD(ha->response_dma));

	WRT_REG_WORD(ISP_REQ_Q_IN(ha, reg), 0);
	WRT_REG_WORD(ISP_REQ_Q_OUT(ha, reg), 0);
	WRT_REG_WORD(ISP_RSP_Q_IN(ha, reg), 0);
	WRT_REG_WORD(ISP_RSP_Q_OUT(ha, reg), 0);
	RD_REG_WORD(ISP_RSP_Q_OUT(ha, reg));		/* PCI Posting. */
}

void
qla24xx_config_rings(struct scsi_qla_host *ha)
{
	struct device_reg_24xx __iomem *reg = &ha->iobase->isp24;
	struct init_cb_24xx *icb;

	/* Setup ring parameters in initialization control block. */
	icb = (struct init_cb_24xx *)ha->init_cb;
	icb->request_q_outpointer = __constant_cpu_to_le16(0);
	icb->response_q_inpointer = __constant_cpu_to_le16(0);
	icb->request_q_length = cpu_to_le16(ha->request_q_length);
	icb->response_q_length = cpu_to_le16(ha->response_q_length);
	icb->request_q_address[0] = cpu_to_le32(LSD(ha->request_dma));
	icb->request_q_address[1] = cpu_to_le32(MSD(ha->request_dma));
	icb->response_q_address[0] = cpu_to_le32(LSD(ha->response_dma));
	icb->response_q_address[1] = cpu_to_le32(MSD(ha->response_dma));

	WRT_REG_DWORD(&reg->req_q_in, 0);
	WRT_REG_DWORD(&reg->req_q_out, 0);
	WRT_REG_DWORD(&reg->rsp_q_in, 0);
	WRT_REG_DWORD(&reg->rsp_q_out, 0);
	RD_REG_DWORD(&reg->rsp_q_out);
}

/**
 * qla2x00_init_rings() - Initializes firmware.
 * @ha: HA context
 *
 * Beginning of request ring has initialization control block already built
 * by nvram config routine.
 *
 * Returns 0 on success.
 */
static int
qla2x00_init_rings(scsi_qla_host_t *ha)
{
	int	rval;
	unsigned long flags = 0;
	int cnt;

	spin_lock_irqsave(&ha->hardware_lock, flags);

	/* Clear outstanding commands array. */
	for (cnt = 0; cnt < MAX_OUTSTANDING_COMMANDS; cnt++)
		ha->outstanding_cmds[cnt] = NULL;

	ha->current_outstanding_cmd = 0;

	/* Clear RSCN queue. */
	ha->rscn_in_ptr = 0;
	ha->rscn_out_ptr = 0;

	/* Initialize firmware. */
	ha->request_ring_ptr  = ha->request_ring;
	ha->req_ring_index    = 0;
	ha->req_q_cnt         = ha->request_q_length;
	ha->response_ring_ptr = ha->response_ring;
	ha->rsp_ring_index    = 0;

	/* Initialize response queue entries */
	qla2x00_init_response_q_entries(ha);

	ha->isp_ops.config_rings(ha);

	spin_unlock_irqrestore(&ha->hardware_lock, flags);

	/* Update any ISP specific firmware options before initialization. */
	ha->isp_ops.update_fw_options(ha);

	DEBUG(printk("scsi(%ld): Issue init firmware.\n", ha->host_no));
	rval = qla2x00_init_firmware(ha, ha->init_cb_size);
	if (rval) {
		DEBUG2_3(printk("scsi(%ld): Init firmware **** FAILED ****.\n",
		    ha->host_no));
	} else {
		DEBUG3(printk("scsi(%ld): Init firmware -- success.\n",
		    ha->host_no));
	}

	return (rval);
}

/**
 * qla2x00_fw_ready() - Waits for firmware ready.
 * @ha: HA context
 *
 * Returns 0 on success.
 */
static int
qla2x00_fw_ready(scsi_qla_host_t *ha)
{
	int		rval;
	unsigned long	wtime, mtime;
	uint16_t	min_wait;	/* Minimum wait time if loop is down */
	uint16_t	wait_time;	/* Wait time if loop is coming ready */
	uint16_t	fw_state;

	rval = QLA_SUCCESS;

	/* 20 seconds for loop down. */
	min_wait = 20;

	/*
	 * Firmware should take at most one RATOV to login, plus 5 seconds for
	 * our own processing.
	 */
	if ((wait_time = (ha->retry_count*ha->login_timeout) + 5) < min_wait) {
		wait_time = min_wait;
	}

	/* Min wait time if loop down */
	mtime = jiffies + (min_wait * HZ);

	/* wait time before firmware ready */
	wtime = jiffies + (wait_time * HZ);

	/* Wait for ISP to finish LIP */
	if (!ha->flags.init_done)
 		qla_printk(KERN_INFO, ha, "Waiting for LIP to complete...\n");

	DEBUG3(printk("scsi(%ld): Waiting for LIP to complete...\n",
	    ha->host_no));

	do {
		rval = qla2x00_get_firmware_state(ha, &fw_state);
		if (rval == QLA_SUCCESS) {
			if (fw_state < FSTATE_LOSS_OF_SYNC) {
				ha->device_flags &= ~DFLG_NO_CABLE;
			}
			if (fw_state == FSTATE_READY) {
				DEBUG(printk("scsi(%ld): F/W Ready - OK \n",
				    ha->host_no));

				qla2x00_get_retry_cnt(ha, &ha->retry_count,
				    &ha->login_timeout, &ha->r_a_tov);

				rval = QLA_SUCCESS;
				break;
			}

			rval = QLA_FUNCTION_FAILED;

			if (atomic_read(&ha->loop_down_timer) &&
			    (fw_state >= FSTATE_LOSS_OF_SYNC ||
				fw_state == FSTATE_WAIT_AL_PA)) {
				/* Loop down. Timeout on min_wait for states
				 * other than Wait for Login.
				 */
				if (time_after_eq(jiffies, mtime)) {
					qla_printk(KERN_INFO, ha,
					    "Cable is unplugged...\n");

					ha->device_flags |= DFLG_NO_CABLE;
					break;
				}
			}
		} else {
			/* Mailbox cmd failed. Timeout on min_wait. */
			if (time_after_eq(jiffies, mtime))
				break;
		}

		if (time_after_eq(jiffies, wtime))
			break;

		/* Delay for a while */
		msleep(500);

		DEBUG3(printk("scsi(%ld): fw_state=%x curr time=%lx.\n",
		    ha->host_no, fw_state, jiffies));
	} while (1);

	DEBUG(printk("scsi(%ld): fw_state=%x curr time=%lx.\n",
	    ha->host_no, fw_state, jiffies));

	if (rval) {
		DEBUG2_3(printk("scsi(%ld): Firmware ready **** FAILED ****.\n",
		    ha->host_no));
	}

	return (rval);
}

/*
*  qla2x00_configure_hba
*      Setup adapter context.
*
* Input:
*      ha = adapter state pointer.
*
* Returns:
*      0 = success
*
* Context:
*      Kernel context.
*/
static int
qla2x00_configure_hba(scsi_qla_host_t *ha)
{
	int       rval;
	uint16_t      loop_id;
	uint16_t      topo;
	uint8_t       al_pa;
	uint8_t       area;
	uint8_t       domain;
	char		connect_type[22];

	/* Get host addresses. */
	rval = qla2x00_get_adapter_id(ha,
	    &loop_id, &al_pa, &area, &domain, &topo);
	if (rval != QLA_SUCCESS) {
		if (LOOP_TRANSITION(ha) || atomic_read(&ha->loop_down_timer) ||
		    (rval == QLA_COMMAND_ERROR && loop_id == 0x7)) {
			DEBUG2(printk("%s(%ld) Loop is in a transition state\n",
			    __func__, ha->host_no));
		} else {
			qla_printk(KERN_WARNING, ha,
			    "ERROR -- Unable to get host loop ID.\n");
			set_bit(ISP_ABORT_NEEDED, &ha->dpc_flags);
		}
		return (rval);
	}

	if (topo == 4) {
		qla_printk(KERN_INFO, ha,
			"Cannot get topology - retrying.\n");
		return (QLA_FUNCTION_FAILED);
	}

	ha->loop_id = loop_id;

	/* initialize */
	ha->min_external_loopid = SNS_FIRST_LOOP_ID;
	ha->operating_mode = LOOP;

	switch (topo) {
	case 0:
		DEBUG3(printk("scsi(%ld): HBA in NL topology.\n",
		    ha->host_no));
		ha->current_topology = ISP_CFG_NL;
		strcpy(connect_type, "(Loop)");
		break;

	case 1:
		DEBUG3(printk("scsi(%ld): HBA in FL topology.\n",
		    ha->host_no));
		ha->current_topology = ISP_CFG_FL;
		strcpy(connect_type, "(FL_Port)");
		break;

	case 2:
		DEBUG3(printk("scsi(%ld): HBA in N P2P topology.\n",
		    ha->host_no));
		ha->operating_mode = P2P;
		ha->current_topology = ISP_CFG_N;
		strcpy(connect_type, "(N_Port-to-N_Port)");
		break;

	case 3:
		DEBUG3(printk("scsi(%ld): HBA in F P2P topology.\n",
		    ha->host_no));
		ha->operating_mode = P2P;
		ha->current_topology = ISP_CFG_F;
		strcpy(connect_type, "(F_Port)");
		break;

	default:
		DEBUG3(printk("scsi(%ld): HBA in unknown topology %x. "
		    "Using NL.\n",
		    ha->host_no, topo));
		ha->current_topology = ISP_CFG_NL;
		strcpy(connect_type, "(Loop)");
		break;
	}

	/* Save Host port and loop ID. */
	/* byte order - Big Endian */
	ha->d_id.b.domain = domain;
	ha->d_id.b.area = area;
	ha->d_id.b.al_pa = al_pa;

	if (!ha->flags.init_done)
 		qla_printk(KERN_INFO, ha,
		    "Topology - %s, Host Loop address 0x%x\n",
 		    connect_type, ha->loop_id);

	if (rval) {
		DEBUG2_3(printk("scsi(%ld): FAILED.\n", ha->host_no));
	} else {
		DEBUG3(printk("scsi(%ld): exiting normally.\n", ha->host_no));
	}

	return(rval);
}

/*
* NVRAM configuration for ISP 2xxx
*
* Input:
*      ha                = adapter block pointer.
*
* Output:
*      initialization control block in response_ring
*      host adapters parameters in host adapter block
*
* Returns:
*      0 = success.
*/
int
qla2x00_nvram_config(scsi_qla_host_t *ha)
{
	int             rval;
	uint8_t         chksum = 0;
	uint16_t        cnt;
	uint8_t         *dptr1, *dptr2;
	init_cb_t       *icb = ha->init_cb;
	nvram_t         *nv = (nvram_t *)ha->request_ring;
	uint8_t         *ptr = (uint8_t *)ha->request_ring;
	struct device_reg_2xxx __iomem *reg = &ha->iobase->isp;

	rval = QLA_SUCCESS;

	/* Determine NVRAM starting address. */
	ha->nvram_size = sizeof(nvram_t);
	ha->nvram_base = 0;
	if (!IS_QLA2100(ha) && !IS_QLA2200(ha) && !IS_QLA2300(ha))
		if ((RD_REG_WORD(&reg->ctrl_status) >> 14) == 1)
			ha->nvram_base = 0x80;

	/* Get NVRAM data and calculate checksum. */
	ha->isp_ops.read_nvram(ha, ptr, ha->nvram_base, ha->nvram_size);
	for (cnt = 0, chksum = 0; cnt < ha->nvram_size; cnt++)
		chksum += *ptr++;

	DEBUG5(printk("scsi(%ld): Contents of NVRAM\n", ha->host_no));
	DEBUG5(qla2x00_dump_buffer((uint8_t *)ha->request_ring,
	    ha->nvram_size));

	/* Bad NVRAM data, set defaults parameters. */
	if (chksum || nv->id[0] != 'I' || nv->id[1] != 'S' ||
	    nv->id[2] != 'P' || nv->id[3] != ' ' || nv->nvram_version < 1) {
		/* Reset NVRAM data. */
		qla_printk(KERN_WARNING, ha, "Inconsistent NVRAM detected: "
		    "checksum=0x%x id=%c version=0x%x.\n", chksum, nv->id[0],
		    nv->nvram_version);
		qla_printk(KERN_WARNING, ha, "Falling back to functioning (yet "
		    "invalid -- WWPN) defaults.\n");

		/*
		 * Set default initialization control block.
		 */
		memset(nv, 0, ha->nvram_size);
		nv->parameter_block_version = ICB_VERSION;

		if (IS_QLA23XX(ha)) {
			nv->firmware_options[0] = BIT_2 | BIT_1;
			nv->firmware_options[1] = BIT_7 | BIT_5;
			nv->add_firmware_options[0] = BIT_5;
			nv->add_firmware_options[1] = BIT_5 | BIT_4;
			nv->frame_payload_size = __constant_cpu_to_le16(2048);
			nv->special_options[1] = BIT_7;
		} else if (IS_QLA2200(ha)) {
			nv->firmware_options[0] = BIT_2 | BIT_1;
			nv->firmware_options[1] = BIT_7 | BIT_5;
			nv->add_firmware_options[0] = BIT_5;
			nv->add_firmware_options[1] = BIT_5 | BIT_4;
			nv->frame_payload_size = __constant_cpu_to_le16(1024);
		} else if (IS_QLA2100(ha)) {
			nv->firmware_options[0] = BIT_3 | BIT_1;
			nv->firmware_options[1] = BIT_5;
			nv->frame_payload_size = __constant_cpu_to_le16(1024);
		}

		nv->max_iocb_allocation = __constant_cpu_to_le16(256);
		nv->execution_throttle = __constant_cpu_to_le16(16);
		nv->retry_count = 8;
		nv->retry_delay = 1;

		nv->port_name[0] = 33;
		nv->port_name[3] = 224;
		nv->port_name[4] = 139;

		nv->login_timeout = 4;

		/*
		 * Set default host adapter parameters
		 */
		nv->host_p[1] = BIT_2;
		nv->reset_delay = 5;
		nv->port_down_retry_count = 8;
		nv->max_luns_per_target = __constant_cpu_to_le16(8);
		nv->link_down_timeout = 60;

		rval = 1;
	}

#if defined(CONFIG_IA64_GENERIC) || defined(CONFIG_IA64_SGI_SN2)
	/*
	 * The SN2 does not provide BIOS emulation which means you can't change
	 * potentially bogus BIOS settings. Force the use of default settings
	 * for link rate and frame size.  Hope that the rest of the settings
	 * are valid.
	 */
	if (ia64_platform_is("sn2")) {
		nv->frame_payload_size = __constant_cpu_to_le16(2048);
		if (IS_QLA23XX(ha))
			nv->special_options[1] = BIT_7;
	}
#endif

	/* Reset Initialization control block */
	memset(icb, 0, ha->init_cb_size);

	/*
	 * Setup driver NVRAM options.
	 */
	nv->firmware_options[0] |= (BIT_6 | BIT_1);
	nv->firmware_options[0] &= ~(BIT_5 | BIT_4);
	nv->firmware_options[1] |= (BIT_5 | BIT_0);
	nv->firmware_options[1] &= ~BIT_4;

	if (IS_QLA23XX(ha)) {
		nv->firmware_options[0] |= BIT_2;
		nv->firmware_options[0] &= ~BIT_3;
		nv->add_firmware_options[1] |= BIT_5 | BIT_4;

		if (IS_QLA2300(ha)) {
			if (ha->fb_rev == FPM_2310) {
				strcpy(ha->model_number, "QLA2310");
			} else {
				strcpy(ha->model_number, "QLA2300");
			}
		} else {
			if (rval == 0 &&
			    memcmp(nv->model_number, BINZERO,
				    sizeof(nv->model_number)) != 0) {