mpi_log_sas.h
来自「linux2.6.16版本」· C头文件 代码 · 共 163 行
H
163 行
/*************************************************************************** * * * Copyright 2003 LSI Logic Corporation. All rights reserved. * * * * This file is confidential and a trade secret of LSI Logic. The * * receipt of or possession of this file does not convey any rights to * * reproduce or disclose its contents or to manufacture, use, or sell * * anything it may describe, in whole, or in part, without the specific * * written consent of LSI Logic Corporation. * * * *************************************************************************** * * Name: iopiIocLogInfo.h * Title: SAS Firmware IOP Interface IOC Log Info Definitions * Programmer: Guy Kendall * Creation Date: September 24, 2003 * * Version History * --------------- * * Last Updated * ------------- * Version %version: 22 % * Date Updated %date_modified: % * Programmer %created_by: nperucca % * * Date Who Description * -------- --- ------------------------------------------------------- * 09/24/03 GWK Initial version * * * Description * ------------ * This include file contains SAS firmware interface IOC Log Info codes * *------------------------------------------------------------------------- */#ifndef IOPI_IOCLOGINFO_H_INCLUDED#define IOPI_IOCLOGINFO_H_INCLUDED/****************************************************************************//* IOC LOGINFO defines, 0x00000000 - 0x0FFFFFFF *//* Format: *//* Bits 31-28: MPI_IOCLOGINFO_TYPE_SAS (3) *//* Bits 27-24: IOC_LOGINFO_ORIGINATOR: 0=IOP, 1=PL, 2=IR *//* Bits 23-16: LOGINFO_CODE *//* Bits 15-0: LOGINFO_CODE Specific *//****************************************************************************//****************************************************************************//* IOC_LOGINFO_ORIGINATOR defines *//****************************************************************************/#define IOC_LOGINFO_ORIGINATOR_IOP (0x00000000)#define IOC_LOGINFO_ORIGINATOR_PL (0x01000000)#define IOC_LOGINFO_ORIGINATOR_IR (0x02000000)/****************************************************************************//* LOGINFO_CODE defines *//****************************************************************************/#define IOC_LOGINFO_CODE_MASK (0x00FF0000)#define IOC_LOGINFO_CODE_SHIFT (16)/****************************************************************************//* IOP LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = IOP *//****************************************************************************/#define IOP_LOGINFO_CODE_INVALID_SAS_ADDRESS (0x00010000)#define IOP_LOGINFO_CODE_UNUSED2 (0x00020000)#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE (0x00030000)#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_RT (0x00030100) /* Route Table Entry not found */#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PN (0x00030200) /* Invalid Page Number */#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_FORM (0x00030300) /* Invalid FORM */#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PT (0x00030400) /* Invalid Page Type */#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DNM (0x00030500) /* Device Not Mapped */#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PERSIST (0x00030600) /* Persistent Page not found */#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DEFAULT (0x00030700) /* Default Page not found */#define IOP_LOGINFO_CODE_TASK_TERMINATED (0x00050000)/****************************************************************************//* PL LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = PL *//****************************************************************************/#define PL_LOGINFO_CODE_OPEN_FAILURE (0x00010000)#define PL_LOGINFO_CODE_INVALID_SGL (0x00020000)#define PL_LOGINFO_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH (0x00030000)#define PL_LOGINFO_CODE_FRAME_XFER_ERROR (0x00040000)#define PL_LOGINFO_CODE_TX_FM_CONNECTED_LOW (0x00050000)#define PL_LOGINFO_CODE_SATA_NON_NCQ_RW_ERR_BIT_SET (0x00060000)#define PL_LOGINFO_CODE_SATA_READ_LOG_RECEIVE_DATA_ERR (0x00070000)#define PL_LOGINFO_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR (0x00080000)#define PL_LOGINFO_CODE_SATA_ERR_IN_RCV_SET_DEV_BIT_FIS (0x00090000)#define PL_LOGINFO_CODE_RX_FM_INVALID_MESSAGE (0x000A0000)#define PL_LOGINFO_CODE_RX_CTX_MESSAGE_VALID_ERROR (0x000B0000)#define PL_LOGINFO_CODE_RX_FM_CURRENT_FRAME_ERROR (0x000C0000)#define PL_LOGINFO_CODE_SATA_LINK_DOWN (0x000D0000)#define PL_LOGINFO_CODE_DISCOVERY_SATA_INIT_W_IOS (0x000E0000)#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE (0x000F0000)#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_PT (0x000F0100) /* Invalid Page Type */#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NUM_PHYS (0x000F0200) /* Invalid Number of Phys */#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NOT_IMP (0x000F0300) /* Case Not Handled */#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NO_DEV (0x000F0400) /* No Device Found */#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_FORM (0x000F0500) /* Invalid FORM */#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_PHY (0x000F0600) /* Invalid Phy */#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NO_OWNER (0x000F0700) /* No Owner Found */#define PL_LOGINFO_CODE_DSCVRY_SATA_INIT_TIMEOUT (0x00100000)#define PL_LOGINFO_CODE_RESET (0x00110000)#define PL_LOGINFO_CODE_ABORT (0x00120000)#define PL_LOGINFO_CODE_IO_NOT_YET_EXECUTED (0x00130000)#define PL_LOGINFO_CODE_IO_EXECUTED (0x00140000)#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE (0x00000100)#define PL_LOGINFO_SUB_CODE_INVALID_SGL (0x00000200)#define PL_LOGINFO_SUB_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH (0x00000300)#define PL_LOGINFO_SUB_CODE_FRAME_XFER_ERROR (0x00000400)#define PL_LOGINFO_SUB_CODE_TX_FM_CONNECTED_LOW (0x00000500)#define PL_LOGINFO_SUB_CODE_SATA_NON_NCQ_RW_ERR_BIT_SET (0x00000600)#define PL_LOGINFO_SUB_CODE_SATA_READ_LOG_RECEIVE_DATA_ERR (0x00000700)#define PL_LOGINFO_SUB_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR (0x00000800)#define PL_LOGINFO_SUB_CODE_SATA_ERR_IN_RCV_SET_DEV_BIT_FIS (0x00000900)#define PL_LOGINFO_SUB_CODE_RX_FM_INVALID_MESSAGE (0x00000A00)#define PL_LOGINFO_SUB_CODE_RX_CTX_MESSAGE_VALID_ERROR (0x00000B00)#define PL_LOGINFO_SUB_CODE_RX_FM_CURRENT_FRAME_ERROR (0x00000C00)#define PL_LOGINFO_SUB_CODE_SATA_LINK_DOWN (0x00000D00)#define PL_LOGINFO_SUB_CODE_DISCOVERY_SATA_INIT_W_IOS (0x00000E00)#define PL_LOGINFO_SUB_CODE_DSCVRY_SATA_INIT_TIMEOUT (0x00001000)#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_FRAME_FAILURE (0x00200000) /* Can't get SMP Frame */#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_READ_ERROR (0x00200001) /* Error occured on SMP Read */#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_WRITE_ERROR (0x00200002) /* Error occured on SMP Write */#define PL_LOGINFO_CODE_ENCL_MGMT_NOT_SUPPORTED_ON_ENCL (0x00200004) /* Encl Mgmt services not available for this WWID */#define PL_LOGINFO_CODE_ENCL_MGMT_ADDR_MODE_NOT_SUPPORTED (0x00200005) /* Address Mode not suppored */#define PL_LOGINFO_CODE_ENCL_MGMT_BAD_SLOT_NUM (0x00200006) /* Invalid Slot Number in SEP Msg */#define PL_LOGINFO_CODE_ENCL_MGMT_SGPIO_NOT_PRESENT (0x00200007) /* SGPIO not present/enabled */#define PL_LOGINFO_DA_SEP_NOT_PRESENT (0x00200100) /* SEP not present when msg received */#define PL_LOGINFO_DA_SEP_SINGLE_THREAD_ERROR (0x00200101) /* Can only accept 1 msg at a time */#define PL_LOGINFO_DA_SEP_ISTWI_INTR_IN_IDLE_STATE (0x00200102) /* ISTWI interrupt recvd. while IDLE */#define PL_LOGINFO_DA_SEP_RECEIVED_NACK_FROM_SLAVE (0x00200103) /* SEP NACK'd, it is busy */#define PL_LOGINFO_DA_SEP_BAD_STATUS_HDR_CHKSUM (0x00200104) /* SEP stopped or sent bad chksum in Hdr */#define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_1 (0x00200105) /* SEP returned unknown scsi status */#define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_2 (0x00200106) /* SEP returned unknown scsi status */#define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP (0x00200107) /* SEP returned bad chksum after STOP */#define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP_GETDATA (0x00200108) /* SEP returned bad chksum after STOP while gettin data*//****************************************************************************//* IR LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = IR *//****************************************************************************/#define IR_LOGINFO_CODE_UNUSED1 (0x00010000)#define IR_LOGINFO_CODE_UNUSED2 (0x00020000)/****************************************************************************//* Defines for convienence *//****************************************************************************/#define IOC_LOGINFO_PREFIX_IOP ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_IOP)#define IOC_LOGINFO_PREFIX_PL ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_PL)#define IOC_LOGINFO_PREFIX_IR ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_IR)#endif /* end of file */⌨️ 快捷键说明
复制代码Ctrl + C
搜索代码Ctrl + F
全屏模式F11
增大字号Ctrl + =
减小字号Ctrl + -
显示快捷键?