eth_miim.v

该文件包含以太网IP核的相关代码

//////////////////////////////////////////////////////////////////////
////                                                              ////
////  eth_miim.v                                                  ////
////                                                              ////
////  This file is part of the Ethernet IP core project           ////
////  http://www.opencores.org/cores/ethmac/                      ////
////                                                              ////
////  Author(s):                                                  ////
////      - Igor Mohor ([e-mail])                      ////
////                                                              ////
////  All additional information is avaliable in the Readme.txt   ////
////  file.                                                       ////
////                                                              ////
//////////////////////////////////////////////////////////////////////
////                                                              ////
//// Copyright (C) 2001 Authors                                   ////
////                                                              ////
//// This source file may be used and distributed without         ////
//// restriction provided that this copyright statement is not    ////
//// removed from the file and that any derivative work contains  ////
//// the original copyright notice and the associated disclaimer. ////
////                                                              ////
//// This source file is free software; you can redistribute it   ////
//// and/or modify it under the terms of the GNU Lesser General   ////
//// Public License as published by the Free Software Foundation; ////
//// either version 2.1 of the License, or (at your option) any   ////
//// later version.                                               ////
////                                                              ////
//// This source is distributed in the hope that it will be       ////
//// useful, but WITHOUT ANY WARRANTY; without even the implied   ////
//// warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR      ////
//// PURPOSE.  See the GNU Lesser General Public License for more ////
//// details.                                                     ////
////                                                              ////
//// You should have received a copy of the GNU Lesser General    ////
//// Public License along with this source; if not, download it   ////
//// from http://www.opencores.org/lgpl.shtml                     ////
////                                                              ////
//////////////////////////////////////////////////////////////////////
//
// CVS Revision History
//
// $Log: eth_miim.v,v $
// Revision 1.2  2001/10/19 08:43:51  mohor
// eth_timescale.v changed to timescale.v This is done because of the
// simulation of the few cores in a one joined project.
//
// Revision 1.1  2001/08/06 14:44:29  mohor
// A define FPGA added to select between Artisan RAM (for ASIC) and Block Ram (For Virtex).
// Include files fixed to contain no path.
// File names and module names changed ta have a eth_ prologue in the name.
// File eth_timescale.v is used to define timescale
// All pin names on the top module are changed to contain _I, _O or _OE at the end.
// Bidirectional signal MDIO is changed to three signals (Mdc_O, Mdi_I, Mdo_O
// and Mdo_OE. The bidirectional signal must be created on the top level. This
// is done due to the ASIC tools.
//
// Revision 1.2  2001/08/02 09:25:31  mohor
// Unconnected signals are now connected.
//
// Revision 1.1  2001/07/30 21:23:42  mohor
// Directory structure changed. Files checked and joind together.
//
// Revision 1.3  2001/06/01 22:28:56  mohor
// This files (MIIM) are fully working. They were thoroughly tested. The testbench is not updated.
//
//

`include "timescale.v"


module eth_miim
(
  Clk,
  Reset,
  Divider,
  NoPre,
  CtrlData,
  Rgad,
  Fiad,
  WCtrlData,
  RStat,
  ScanStat,
  Mdi,
  Mdo,
  MdoEn,
  Mdc,
  Busy,
  Prsd,
  LinkFail,
  Nvalid,
  WCtrlDataStart,
  RStatStart,
  UpdateMIIRX_DATAReg
);



input         Clk;                // Host Clock
input         Reset;              // General Reset
input   [7:0] Divider;            // Divider for the host clock
input  [15:0] CtrlData;           // Control Data (to be written to the PHY reg.)
input   [4:0] Rgad;               // Register Address (within the PHY)
input   [4:0] Fiad;               // PHY Address
input         NoPre;              // No Preamble (no 32-bit preamble)
input         WCtrlData;          // Write Control Data operation
input         RStat;              // Read Status operation
input         ScanStat;           // Scan Status operation
input         Mdi;                // MII Management Data In

output        Mdc;                // MII Management Data Clock
output        Mdo;                // MII Management Data Output
output        MdoEn;              // MII Management Data Output Enable
output        Busy;               // Busy Signal
output        LinkFail;           // Link Integrity Signal
output        Nvalid;             // Invalid Status (qualifier for the valid scan result)

output [15:0] Prsd;               // Read Status Data (data read from the PHY)

output        WCtrlDataStart;     // This signals resets the WCTRLDATA bit in the MIIM Command register
output        RStatStart;         // This signal resets the RSTAT BIT in the MIIM Command register
output        UpdateMIIRX_DATAReg;// Updates MII RX_DATA register with read data

parameter Tp = 1;


reg           Nvalid;
reg           EndBusy_d;          // Pre-end Busy signal
reg           EndBusy;            // End Busy signal (stops the operation in progress)

reg           WCtrlData_q1;       // Write Control Data operation delayed 1 Clk cycle
reg           WCtrlData_q2;       // Write Control Data operation delayed 2 Clk cycles
reg           WCtrlData_q3;       // Write Control Data operation delayed 3 Clk cycles
reg           WCtrlDataStart;     // Start Write Control Data Command (positive edge detected)
reg           WCtrlDataStart_q;
reg           WCtrlDataStart_q1;  // Start Write Control Data Command delayed 1 Mdc cycle
reg           WCtrlDataStart_q2;  // Start Write Control Data Command delayed 2 Mdc cycles

reg           RStat_q1;           // Read Status operation delayed 1 Clk cycle
reg           RStat_q2;           // Read Status operation delayed 2 Clk cycles
reg           RStat_q3;           // Read Status operation delayed 3 Clk cycles
reg           RStatStart;         // Start Read Status Command (positive edge detected)
reg           RStatStart_q1;      // Start Read Status Command delayed 1 Mdc cycle
reg           RStatStart_q2;      // Start Read Status Command delayed 2 Mdc cycles

reg           ScanStat_q1;        // Scan Status operation delayed 1 cycle
reg           ScanStat_q2;        // Scan Status operation delayed 2 cycles
reg           SyncStatMdcEn;      // Scan Status operation delayed at least cycles and synchronized to MdcEn

wire          WriteDataOp;        // Write Data Operation (positive edge detected)
wire          ReadStatusOp;       // Read Status Operation (positive edge detected)
wire          ScanStatusOp;       // Scan Status Operation (positive edge detected)
wire          StartOp;            // Start Operation (start of any of the preceding operations)
wire          EndOp;              // End of Operation

reg           InProgress;         // Operation in progress
reg           InProgress_q1;      // Operation in progress delayed 1 Mdc cycle
reg           InProgress_q2;      // Operation in progress delayed 2 Mdc cycles
reg           InProgress_q3;      // Operation in progress delayed 3 Mdc cycles

reg           WriteOp;            // Write Operation Latch (When asserted, write operation is in progress)
reg     [6:0] BitCounter;         // Bit Counter


wire          MdcFrame;           // Frame window for limiting the Mdc
wire    [3:0] ByteSelect;         // Byte Select defines which byte (preamble, data, operation, etc.) is loaded and shifted through the shift register.
wire          MdcEn;              // MII Management Data Clock Enable signal is asserted for one Clk period before Mdc rises.
wire          ShiftedBit;         // This bit is output of the shift register and is connected to the Mdo signal


wire          LatchByte1_d2;
wire          LatchByte0_d2;
reg           LatchByte1_d;
reg           LatchByte0_d;
reg     [1:0] LatchByte;          // Latch Byte selects which part of Read Status Data is updated from the shift register

reg           UpdateMIIRX_DATAReg;// Updates MII RX_DATA register with read data





// Generation of the EndBusy signal. It is used for ending the MII Management operation.
always @ (posedge Clk or posedge Reset)
begin
  if(Reset)
    begin
      EndBusy_d <= #Tp 1'b0;
      EndBusy <= #Tp 1'b0;
    end
  else
    begin
      EndBusy_d <= #Tp ~InProgress_q2 & InProgress_q3;
      EndBusy   <= #Tp EndBusy_d;
    end
end


// Update MII RX_DATA register
always @ (posedge Clk or posedge Reset)
begin
  if(Reset)
    UpdateMIIRX_DATAReg <= #Tp 0;
  else
  if(EndBusy & ~WCtrlDataStart_q)
    UpdateMIIRX_DATAReg <= #Tp 1;
  else
    UpdateMIIRX_DATAReg <= #Tp 0;    
end



// Generation of the delayed signals used for positive edge triggering.
always @ (posedge Clk or posedge Reset)
begin
  if(Reset)
    begin
      WCtrlData_q1 <= #Tp 1'b0;