双枪氩弧焊.txt

来自「可以读些S7-300PLC中的变量数据」· 文本 代码 · 共 169 行

"I0.0月牙剪废料电机断路"
"I0.1水泵电机断路"
"I0.2操作侧间隙电机断路"
"I0.3传动侧间隙电机断路"
"I0.4纵对齐电机断路"
"I0.5入口扫描电机断路"
"I0.6出口扫描电机断路"
"I0.7前枪变频器断路"
"I1.0油路堵塞"
"I1.1油位检测"
"I1.2阀电源开启"
"I1.3前枪变频器报警"
"I1.424V阀电源空开断开"
"I1.524V控制电源空开断"
"I1.6后枪变频器断路"
"I1.7后枪变频器报警"
"I2.0刨光泵启停"
"I2.1运行泵启停"
"I2.2高压泵启停"
"I2.3上升按钮"
"I2.4下降按钮"
"I2.5操作侧按钮"
"I2.6传动侧按钮"
"I2.7焊接允许"
"I3.0纵对齐操作侧"
"I3.1纵对齐传动侧"
"I3.2带头点动进"
"I3.3带头点动退"
"I3.4带尾点动进"
"I3.5带尾点动退"
"I3.6手动焊接启动"
"I3.7焊机复位"
"I4.0月牙剪操作允许"
"I4.1月牙剪复位"
"I4.2冲剪启动"
"I4.3冲剪联动"
"I4.4月牙剪出废料"
"I4.5月牙剪操作侧选择"
"I4.6月牙剪传动侧选择"
"I4.7剪头分开"
"I5.0剪头合拢"
"I5.1冲剪上升"
"I5.2冲剪下降"
"I5.3刨光压板夹紧"
"I5.4刨光压板松开"
"I5.5刨刀前进"
"I5.6刨刀后退"
"I5.7刨光启动"
"I6.0刨光操作允许"
"I6.1刨光机架纵向左移"
"I6.2刨光机架纵向右移"
"I6.3刨光机复位"
"I6.4冲孔上升"
"I6.5吹渣"
"I6.6冲孔下降"
"I6.7焊机出废料"
"I7.0"
"I7.1"
"I7.2"
"I7.3"
"I7.4"
"I7.5"
"I7.6"
"I7.7"
"I8.0"
"I8.1入口挑套原位"
"I8.2入口挑套上位"
"I8.3"
"I8.4出口挑套原位"
"I8.5出挑套上位"
"I8.6入口夹钳上位"
"I8.7入口夹钳下位"
"I9.0入口给进原位"
"I9.1入给进到位"
"I9.2出口夹钳上位"
"I9.3出口夹钳下位"
"I9.4纵对齐操作侧原位"
"I9.5纵对齐传动侧原位"
"I9.6"
"I9.7"
"I10.0前枪传动侧停止位"
"I10.1前枪操作侧停止位"
"I10.2上剪刀上位"
"I10.3上剪刀下位"
"I10.4吊板上位"
"I10.5吊板下位"
"I10.6锁销原位"
"I10.7锁销到位"
"I11.0剪刀工作位"
"I11.1电极工作位"
"I11.2下电极原位"
"I11.3下电极上位"
"I11.4前焊枪原位"
"I11.5前焊枪下位"
"I11.6前焊枪斜块上极限"
"I11.7前焊枪斜块下极限"
"I12.0刨光压板上位"
"I12.1刨光压板下位"
"I12.2刨刀原位"
"I12.3刨刀前极限位"
"I12.4刨刀机架横向左原位"
"I12.5刨刀机架横向右原位"
"I12.6冲头上位"
"I12.7冲头下位"
"I13.0操作侧剪头机架原位"
"I13.1操作侧剪头上位"
"I13.2操作侧剪头下位"
"I13.3传动侧剪头机架原位"
"I13.4传动侧剪头上位"
"I13.5传动侧剪头下位"
"I13.6"
"I13.7"
"I14.0操作侧头板光电检"
"I14.1操作侧头板光电检"
"I14.2传动侧头板光电检"
"I14.3传动侧头板光电检"
"I14.4入口光电扫描"
"I14.5出口光电扫描"
"I14.6后枪传动侧停止位"
"I14.7后枪操作侧停止位"
"I15.0后焊枪原位"
"I15.1后焊枪下位"
"I15.2后焊枪斜块上极限"
"I15.3后焊枪斜块下极限"
"I15.4"
"I15.5"
"I15.6"
"I15.7"
"I16.0入口扫描操作极限"
"I16.1入口扫描传动极限"
"I16.2出口扫描操作极限"
"I16.3出口扫描传动极限"
"I16.4纵对齐操作侧极限"
"I16.5纵对齐传动侧极限"
"I16.6操作侧间隙-操作侧"
"I16.7操作侧间隙-传动侧"
"I17.0传动侧间隙-操作侧"
"I17.1传动侧间隙-传动侧"
"I17.2焊接小车操作极限"
"I17.3焊接小车传动极限"
"I17.4操作侧剪头限位"
"I17.5传动侧剪头限位"
"I17.6前后枪防撞保护"
"I17.7"
"I18.0 #1入口对中原位"
"I18.1 #1入口对中OP到位"
"I18.2 #1入口对中DR到位"
"I18.3 #2入口对中原位"
"I18.4 #2入口对中OP到位"
"I18.5 #2入口对中DR到位"
"I18.6 #3入口对中原位"
"I18.7 #3入口对中OP到位"
"I19.0 #3入口对中DR到位"
"I19.1 #4入口对中原位"
"I19.2 #4入口对中OP到位"
"I19.3 #4入口对中DR到位"
"I19.4"
"I19.5"
"I19.6"
"I19.7"
"I20.0"
"I20.1"
"I20.2"
"I20.3"
"I20.4"
"I20.5"
"I20.6"
"I20.7"