📄 bblink.htm
字号:
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN"><!-- The BLINK Program --><HTML><HEAD><TITLE>The BLINK Program</TITLE><META HTTP-EQUIV="content-type" CONTENT="text/html; charset=iso-8859-1"></HEAD><BODY BACKGROUND="spiral.gif" BGCOLOR="#FFFFFF" TEXT="#000000" LINK="#0000FF" VLINK="#990099" ALINK="#FF0000"><TABLE WIDTH="98%"><TR><TD WIDTH=60 VALIGN=BOTTOM NOWRAP><IMG SRC="transp.gif" ALT="" WIDTH=60 HEIGHT=20></TD><TD><!-- Ab hier Seitentext: --><BIG><BR><P><STRONG><U>III.5 The BLINK Program</U></STRONG></P><P>When <NOBR>BOOT-51</NOBR> is customized and blown into an EPROM, and thetarget board is connected to the host PC, it would be nice to verify,whether the whole configuration is working together correctly.This can be done with a short test program that performs a well-definedaction when started. For this purpose the tiny assembly program<EM>blink.a51</EM> has been provided.It simply toggles the logic level of a port pin (roughly) once a second(great if connected to a LED) to verify, whether all the components inthe chain</P><P><CENTER><STRONG>assembly <NOBR> --» </NOBR> <NOBR>serial interface</NOBR><NOBR> --» </NOBR> <NOBR>target system</NOBR><NOBR> «--» </NOBR> <NOBR>bootstrap program</NOBR></STRONG></CENTER></P><P>are working together correctly.<BR>It can be adapted to your requirements with little efforts:</P><P><OL TYPE=1><LI>If your target system carries a LED that can be switched with a bit-addressable port pin, please change the BIT symbol <STRONG>LEDPIN</STRONG> accordingly. Then the program will make the LED blink.<BR> <BR> If your LED can only be switched with a non-bit-addressable port pin (say bit 2 of a port <STRONG>P6</STRONG>), simply replace the <NOBR>statement </NOBR> <NOBR><CODE>CPL LEDPIN </CODE></NOBR> <NOBR>by </NOBR> <NOBR><CODE>XRL P6,#00000100B </CODE></NOBR> or something like that.<BR> </LI><LI>Change the program start address <STRONG>START</STRONG> to the location, where user programs are usually loaded on your target system.<BR> The program code itself is position-independent!</LI></OL></P><P>If there is no LED on your target system, connect the port pin toa volt-meter. This may also do. Aside of <STRONG>P0</STRONG> and <STRONG>P2</STRONG> youmay use every port with LEDs or spare outputs. Now the command</P><P><BLOCKQUOTE><STRONG><PRE>boot blink</PRE></STRONG></BLOCKQUOTE></P><P>should reset the <NOBR>MCS-51</NOBR> board, assemble the test program,upload it to the target system, and finally start it.<BR><IMG SRC="redbled.gif" ALIGN=LEFT HSPACE=8 VSPACE=4 ALT="red LED" WIDTH=28 HEIGHT=28>If the LED is blinking, everything is now perfectly installed and readyfor daily work. If not, you should read the next chapter!</P></BIG><!-- Seitentext Ende --><P><BR><BR><CENTER><TABLE WIDTH="70%"><TR><TH><A HREF="boot51.htm"><IMG SRC="home.gif" ALT="[contents]" BORDER=0 WIDTH=32 HEIGHT=32></A></TH> <TH><A HREF="boperat.htm"><IMG SRC="up.gif" ALT="[up]" BORDER=0 WIDTH=32 HEIGHT=32></A></TH> <TH><A HREF="bscript.htm"><IMG SRC="back.gif" ALT="[back]" BORDER=0 WIDTH=32 HEIGHT=32></A></TH> <TH><A HREF="btrouble.htm"><IMG SRC="next.gif" ALT="[next]" BORDER=0 WIDTH=32 HEIGHT=32></A></TH></TR></TABLE></CENTER></P></TD></TR></TABLE></BODY></HTML>⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -